电动汽车转矩定向分配差速器建模与动态仿真

本文中提出一种新型具备转矩定向分配功能差速器的集中式电驱动桥系统。该集中驱动系统可以在不改变总驱动转矩的条件下,类似分布式驱动方式实现驱动转矩在左右轮间的任意分配,从而产生改变车辆横摆动力学的直接横摆力偶矩。首先,分析了转矩定向分配差速器结构特点及其工作原理;其次,利用键合图理论建立了其动力学模型,并仿真分析了其动态响应特性;然后,设计了转矩响应控制系统以改善该差速器的动态性能;最后,嵌入整车模型进行了联合仿真。结果表明,装备该差速器的车辆可任意分配左右轮驱动转矩,并有效改善车辆操控特性。     

分布式驱动电动汽车转向工况转矩分配控制研究

针对分布式驱动车辆转向工况在低速下期望提高转向机动性能,高速下期望保证行驶稳定性的需求,充分考虑转向行驶内外侧车轮的转向关系以及车辆动力学,制定了适应车速变化的四轮转矩分配策略,建立了四轮轮毂电机驱动模型以及二自由度参考模型。为了改善分布式驱动转向机动性能,建立自抗扰控制器调整内外侧车轮转矩,形成合理的转速差,减小转向半径,以提高转向机动性;对于高速转向行驶稳定性的需求,通过二次规划方法优化分配各车轮驱动力矩,分析轮胎纵横向附着裕度建立目标函数,并加入附加横摆力矩和路面附着力的限制,进行车轮驱动转矩的在线优化分配,提高车辆转向行驶的稳定性;另外为避免2种控制模式转换时驱动转矩突变,根据车速和稳定性参数制定模糊规则决策2种模式的协调系数,保证2种控制模式的平滑过渡。基于CarSim和MATLAB/Simulink进行联合仿真,并搭建硬件在环平台进行试验,对所提出的方法进行验证。结果表明：在低速转向工况下,提出的分配策略能够调节内外侧车轮产生差速效果,与转矩平均分配的策略相比,转向半径有所减小,提高车辆机动性;高速转向工况下,分配策略能够保证车辆稳定转向,与未考虑稳定性控制的分配策略相比,能更好地跟踪目标轨迹,且横摆角速度控制在参考横摆角速度附近,证明了所提控制策略的有效性。     

基于动态门限值的分布式驱动电动汽车驱动力矩控制研究

为改善分布式驱动电动汽车高速行驶稳定性，避免频繁驱动控制操作对汽车行驶安全性的影响，提出了一种适应不同驾驶工况的参数动态门限值算法，设计了汽车附加横摆力矩滑模控制策略和驱动力矩二次规划优化分配控制策略，并进行了角阶跃输入工况和双正弦输入工况的仿真分析。结果表明，所设计的控制策略能有效控制汽车的质心侧偏角与横摆角速度，在保证汽车行驶稳定性的前提下，使质心侧偏角与理想值偏差减小了3.6%以上，轮胎附着利用率减少19.5%以上，有效地降低了轮胎附着利用率，提高了汽车的行驶安全性。     

Nonlinear optimal integrated vehicle control using individual braking torque and steering angle with on-line control allocation by using state-dependent Riccati equation technique

This paper proposes the solution of state-dependent Riccati equation as a nonlinear optimal regulator to stabilise the motion dynamics of the vehicle model subjected to sudden disturbance inputs in the lateral direction. The proposed nonlinear regulator coordinates individually actuated wheel braking torque and steering wheel angle simultaneously in an optimal manner. Performance criteria are satisfied by solving the Riccati equation based on the given cost function subjected to the nonlinear vehicle dynamics. On-line control allocation in terms of optimal brake torque distribution enhanced by optimal wheel steering angle input is achieved. Furthermore, the proposed optimal nonlinear regulator is an active fault-tolerant control system against partial by-wire actuator failures while guaranteeing stability with good performance due to its capability to allocate the individual control inputs in an optimal way. The main aim is to stabilise the motion dynamics of the vehicle model during short-term emergency situations along the desired straight trajectory manageable by average drivers and to provide vehicle stability and handling predictability through the interaction of individual wheel braking and steering actuators. Simulation results are used to illustrate the effectiveness of the proposed methodology.     

Cooperative regenerative braking control for front-wheel-drive hybrid electric vehicle based on adaptive regenerative brake torque optimization using under-steer index

In this study, cooperative regenerative braking control of front-wheel-drive hybrid electric vehicle is proposed to recover optimal braking energy while guaranteeing the vehicle lateral stability. In front-wheel-drive hybrid electric vehicle, excessive regenerative braking for recuperation of the maximum braking energy can cause under-steer problem. This is due to the fact that the resultant lateral force on front tire saturates and starts to decrease. Therefore, cost function with constraints is newly defined to determine optimum distribution of brake torques including the regenerative brake torque for improving the braking energy recovery as well as the vehicle lateral stability. This cost function includes trade-off relation of two objectives. The physical meaning of first objective of cost function is to maximize the regenerative brake torque for improving the fuel economy and that of second objective is to increase the mechanical-friction brake torques at rear wheels rather than regenerative brake torque at front wheels for preventing front tire saturation. And weighting factor in cost function is also proposed as a function of under-steer index representing current state of the vehicle lateral motion in order to generalize the constrained optimization problem including both normal and severe cornering situation. For example, as the vehicle approaches its handling limits, adaptation of weighting factor is possible to prioritize front tire saturation over increasing the recuperation of braking energy for driver safety and vehicle lateral stability. Finally, computer simulation of closed loop driver-vehicle system based on Carsim? performed to verify the effectiveness of adaptation method in proposed controller and the vehicle performance of the proposed controller in comparison with the conventional controller for only considering the vehicle lateral stability. Simulation results indicate that the proposed controller improved the performance of braking energy recovery as well as guaranteed the vehicle lateral stability similar to the conventional controller.     

分布式驱动电动汽车转矩节能优化分配

为了提高分布式驱动电动汽车的经济性和续航里程,对4个轮毂电机驱动转矩优化分配问题进行研究。通过轮毂电机台架试验得到轮毂电机的驱动效率特性,分析转矩优化分配实现节约整车能耗的可行性;建立侧重提高电机效率的目标函数,使电机转矩处于电机效率Map图中的高效区;建立侧重提高电机响应速度的目标函数,减小转矩分配瞬间电流波动过大带来的能耗;基于模糊理论设计以电机效率为变量的权重函数,实时调节权重来协调2种目标函数,提出一种转矩节能优化分配方法,得到最优的轴间转矩分配系数。在后轴驱动、平均分配、优化分配3种分配方式下进行整车能耗的ECE城市循环工况对比仿真分析。结果表明：提出的节能优化分配方法通过实时优化驱动电机的转矩,避免了电机工作在转矩过大和过小的低效区,提高了整个驱动系统的能量利用率,相比于后轴驱动和平均分配整车能耗效率提高了5.91%和10.54%;实车试验验证了转矩节能优化分配算法的节能效果,优化分配相比另外2种分配方式整车能耗效率分别提高了3.66%和8.58%。     

A novel integrated chassis controller for full drive-by-wire vehicles

In this paper, a systematic design with multiple hierarchical layers is adopted in the integrated chassis controller for full drive-by-wire vehicles. A reference model and the optimal preview acceleration driver model are utilised in the driver control layer to describe and realise the driver's anticipation of the vehicle's handling characteristics, respectively. Both the sliding mode control and terminal sliding mode control techniques are employed in the vehicle motion control (MC) layer to determine the MC efforts such that better tracking performance can be attained. In the tyre force allocation layer, a polygonal simplification method is proposed to deal with the constraints of the tyre adhesive limits efficiently and effectively, whereby the load transfer due to both roll and pitch is also taken into account which directly affects the constraints. By calculating the motor torque and steering angle of each wheel in the executive layer, the total workload of four wheels is minimised during normal driving, whereas the MC efforts are maximised in extreme handling conditions. The proposed controller is validated through simulation to improve vehicle stability and handling performance in both open- and closed-loop manoeuvres.     

Multi-axle vehicle dynamics stability control algorithm with all independent drive wheel

The stability driving characteristic and the tire wear of 8-axle vehicle with 16-independent driving wheels are discussed in this paper. The lateral stability of 8-axle vehicle can be improved by the direct yaw moment which is generated by the 16 independent driving wheels. The hierarchical controller is designed to determine the required yaw torque and driving force of each wheel. The upper level controller uses feed-forward and feed-backward control theory to obtain the required yaw torque. The fuzzification weight ratio of two control objective is built in the upper level controller to regulate the vehicle yaw and lateral motions. The rule-based yaw moment distribution strategy and the driving force adjustment based on the safety of vehicle are proposed in the lower level controller. The influence of rear steering angle is considered in the distribution of driving force of the wheel. Simulation results of a vehicle double lane change show the stability of 8-axle vehicle under the proposed control algorithm. The wear rate of tire is calculated by the interaction force between the tire and ground. The wear of tire is different from each other for the vehicle with the stability controller or not.     

Study on integrated control of active front steer angle and direct yaw moment

This study proposes a control system to improve vehicle handling and stability under severe driving conditions by actively controlling the front steering angle and the distribution of braking forces on four tires. With the application of a model-matching control technique, this proposed control system makes the performance of the actual vehicle model follow that of an ideal vehicle model with consideration of nonlinearity of tire characteristics. Finally, this paper investigates the effectiveness of control system during the following conditions: braked cornering, lane change and side wind disturbance.     

Lateral handling improvement with dynamic curvature control for an independent rear wheel drive EV

The integrated longitudinal and lateral dynamic motion control is important for four wheel independent drive (4WID) electric vehicles. Under critical driving conditions, direct yaw moment control (DYC) has been proved as effective for vehicle handling stability and maneuverability by implementing optimized torque distribution of each wheel, especially with independent wheel drive electric vehicles. The intended vehicle path upon driver steering input is heavily depending on the instantaneous vehicle speed, body side slip and yaw rate of a vehicle, which can directly affect the steering effort of driver. In this paper, we propose a dynamic curvature controller (DCC) by applying a the dynamic curvature of the path, derived from vehicle dynamic state variables; yaw rate, side slip angle, and speed of a vehicle. The proposed controller, combined with DYC and wheel longitudinal slip control, is to utilize the dynamic curvature as a target control parameter for a feedback, avoiding estimating the vehicle side-slip angle. The effectiveness of the proposed controller, in view of stability and improved handling, has been validated with numerical simulations and a series of experiments during cornering engaging a disturbance torque driven by two rear independent in-wheel motors of a 4WD micro electric vehicle.     

Optimal power distribution of front and rear motors for minimizing energy consumption of 4-wheel-drive electric vehicles

In this paper, the optimal power distribution of the front and rear motors for minimizing energy consumption of a 4WD EV is investigated. An optimal power distribution control is developed based on the mathematical energy consumption model of an EV. The objective function is defined while ignoring time. And, the time effect is applied by considering the objective function for every single driving point which consists of the vehicle driving force and velocity. From the optimization problem, the optimal torque distribution maps of the front and rear motors can be obtained for all vehicle driving force and velocity ranges. These maps can be expressed using a 3-dimensional map. If the vehicle driving force and velocity are determined, the optimal front and rear motor torques can be determined using these maps. These maps can distribute the front and rear motor torques for the entire velocity range. Thus, these maps can perform the optimal power (torque times speed) distribution of the front and rear motors for minimizing the energy consumption of the 4WD EV. The performance of the optimal power distribution is evaluated by comparing the energy consumption to that of simple power distribution control. For obtaining the energy consumption, a vehicle driving simulation is performed. For the simulation, the driving cycle is required, and the NEDC (New European Driving Cycle) is used. From the simulation results, it is found that the energy consumption of simple power distribution is 4.8 % larger than the optimal one. Thus, the optimal power distribution can minimize the 4WD EV energy consumption as the optimization objective function.     

一种提高轮边驱动客车经济性的驱动控制方法

轮边驱动电动客车采用4个永磁同步电机,通过减速器将驱动力传递至驱动轮。合适的转矩分配控制策略可以提升行车经济性。以轮边驱动电动客车为研究对象,采用加速踏板平滑处理和基于电机电动效率Map图的转矩优化分配方法,并通过AVL Cruise/Simulink联合仿真、dSPACE硬件在环和实车试验进行验证。结果表明,相比于平均转矩分配,采用加速踏板平滑处理和基于电机电动效率Map图的转矩最优分配方法可降低2.35%的能耗,且该控制算法在硬件在环和实车试验中有着较好的实时性,能够满足实车行驶的需求。     

智能分布式驱动汽车路径跟踪/制动能量回收协同控制策略研究

为了解决智能分布式驱动汽车路径跟踪与制动能量回收系统间的协同控制难题,充分考虑分布式驱动汽车四轮扭矩独立可控在智能驾驶系统中的优势,设计适应不同路面附着条件的智能分布式驱动汽车转向、制动分层协同控制策略。上层控制器依据不同的路面类型设计差异化的多目标代价函数,以综合优化各工况下的控制目标。高附路面下,制定满足最大能量回收值的全局参考车速,在线优化路径跟踪指令,实现最优能量回收的同时减小系统运算负荷;低附路面下,优先考虑车辆的路径跟踪性能和行驶稳定性,在多目标代价函数中取消对全局参考车速的跟随要求,增设终端速度约束与能量回收项性能指标并减小能量回收项性能指标的权重系数。上层控制器基于模型预测控制方法对多目标代价函数进行滚动优化与预测求解,得到期望的前轮转角及4个车轮的总制动扭矩需求。下层控制器根据制动扭矩需求对四轮的液压制动扭矩和电机制动扭矩进行分配,最终完成整个复合制动过程。基于MATLAB/Simulink和CarSim软件,搭建控制器在环仿真平台,并在高附和低附路面条件下对所提出的策略进行试验验证。研究结果表明：高附路面下,所提出的控制策略在准确跟踪期望路径的同时相较固定比例制动力分配方法可提升2.7%的能量回收值并减少约0.02 s的单次计算时间;低附路面下,与使用高附控制策略相比,能够保证车辆的路径跟踪准确性与行驶稳定性,同时可提升7.8%的能量回收值;控制器在环试验结果证明了该协同控制策略对车辆性能提升的有效性。     

Integrated control of brake pressure and rear-wheel steering to improve lateral stability with fuzzy logic

This study introduces an integrated dynamic control with steering (IDCS) system to improve vehicle handling and stability under severe driving conditions. It integrates an active rear-wheel steering control system and a direct yawmoment control system with fuzzy logic. Direct yaw-moment control is achieved by modifying the optimal slip of the front outer wheel. An 8-degree-of-freedom vehicle model was used to evaluate the proposed IDCS for various road conditions and driving inputs. The results show that the yaw rate tracked the reference yaw rate and that the body slip angle was reduced when the IDCS was employed, thereby increasing the controllability and stability of the vehicle on slippery roads. The IDCS system reduced the deviation from the center line for a vehicle running on a split m road.     

Dynamics characteristics analysis and control of FWID EV

Compared with internal combustion engine (ICE) vehicles, four-wheel-independently-drive electric vehicles (FWID EV) have significant advantages, such as more controlled degree of freedom (DOF), higher energy efficiency and faster torque response of an electric motor. The influence of these advantages and other characteristics on vehicle dynamics control need to be evaluated in detail. This paper firstly analyzed the dynamics characteristics of FWID EV, including the feasible region of vehicle global force, the improvement of powertrain energy efficiency and the time-delays of electric motor torque in the direct yaw moment feedback control system. In this way, the influence of electric motor output power limit, road friction coefficient and the wheel torque response on the stability control, as well as the impact of motor idle loss on the torque distribution method were illustrated clearly. Then a vehicle dynamics control method based on the vehicle stability state was proposed. In normal driving condition, the powertrain energy efficiency can be improved by torque distribution between front and rear wheels. In extreme driving condition, the electric motors combined with the electro-hydraulic braking system were employed as actuators for direct yaw moment control. Simulation results show that dynamics control which take full advantages of the more controlled freedom and the motor torque response characteristics improve the vehicle stability better than the control based on the hydraulic braking system of conventional vehicle. Furthermore, some road tests in a real vehicle were conducted to evaluate the performance of proposed control method.     

Torque control allocation based on constrained optimization with regenerative braking for electric vehicles

This paper proposes a constrained optimization-based torque control allocation method aimed to improve energy efficiency, and thus, driving range for electric vehicles. In the proposed method, the cost function is defined not only to achieve desired yaw moment for vehicle handling and stability, but also to minimize power losses for energy efficiency. The particular attention is paid to the power losses due to tire slips both longitudinally and laterally. The constraints are also set based on thorough investigation on various causes of power disppation such that the torque is allocated with restraint to use regenerative braking in its maximum capacity. The proposed control allocation method has been tested and verified to be effective on energy efficiency improvement through both simulation and experiment under various driving maneuvers.     

Lateral stability control of dynamic steering for dual motor drive high speed tracked vehicle

In this paper, the torque and power required by dual motors for electric tracked vehicle during dynamic steering maneuvers with different steering radiuses are analyzed. A steering coupling drive system composed of a new type of center steering motor, two Electromagnetic (EM) clutches, two planetary gear couplers, and two propulsion motors is proposed for the dual motors drive high speed electric tracked vehicle (2MHETV), which aims to improve its lateral stability. An average torque direct distribution control strategy based on steering coupling and an optimization-distribution-based close-loop control strategy are designed separately to control the driving torque or regenerative braking torque of two propulsion motors for vehicle stability enhancement. Then models of the 2MHETV and the proposed control strategy are established in Recudyn and Matlab/Simulink respectively to evaluate the lateral stability of dynamic steering for the 2MHETV with different steering radiuses on hard pavement.The simulation results show that the lateral stability of the 2MHETV can be significantly improved by the proposed optimization-distribution-based close-loop control strategy based on steering coupling system.     

A vehicle stability control strategy with adaptive neural network sliding mode theory based on system uncertainty approximation

Modelling uncertainty, parameter variation and unknown external disturbance are the major concerns in the development of an advanced controller for vehicle stability at the limits of handling. Sliding mode control (SMC) method has proved to be robust against parameter variation and unknown external disturbance with satisfactory tracking performance. But modelling uncertainty, such as errors caused in model simplification, is inevitable in model-based controller design, resulting in lowered control quality. The adaptive radial basis function network (ARBFN) can effectively improve the control performance against large system uncertainty by learning to approximate arbitrary nonlinear functions and ensure the global asymptotic stability of the closed-loop system. In this paper, a novel vehicle dynamics stability control strategy is proposed using the adaptive radial basis function network sliding mode control (ARBFN-SMC) to learn system uncertainty and eliminate its adverse effects. This strategy adopts a hierarchical control structure which consists of reference model layer, yaw moment control layer, braking torque allocation layer and executive layer. Co-simulation using MATLAB/Simulink and AMESim is conducted on a verified 15-DOF nonlinear vehicle system model with the integrated-electro-hydraulic brake system (I-EHB) actuator in a Sine With Dwell manoeuvre. The simulation results show that ARBFN-SMC scheme exhibits superior stability and tracking performance in different running conditions compared with SMC scheme.     

Integrated fuzzy/optimal vehicle dynamic control

There are basically two methods to control yaw moment which is the most efficient way to improve vehicle stability and handling. The first method is indirect yaw moment control, which works based on control of the lateral tire force through steering angle control. It is mainly known as active steering control (ASC). Nowadays, the most practical approach to steering control is active front steering (AFS). The other method is direct yaw moment control (DYC), in which an unequal distribution of longitudinal tire forces (mainly braking forces) produces a compensating external yaw moment. It is well known that the AFS performance is limited in the non-linear vehicle handling region. On the other hand, in spite of a good performance of DYC in both the linear and non-linear vehicle handling regions, continued DYC activation could lead to uncomfortable driving conditions and an increase in the stopping distance in the case of emergency braking. It is recommended that DYC be used only in high-g critical maneuvers. In this paper, an integrated fuzzy/optimal AFS/DYC controller has been designed. The control system includes five individual optimal LQR control strategies; each one, has been designed for a specific driving condition. The strategies can cover low, medium, and high lateral acceleration maneuvers on high-μ or low-μ roads. A fuzzy blending logic also has been utilized to mange each LQR control strategy contribution level in the final control action. The simulation results show the advantages of the proposed control system over the individual AFS or DYC controllers.     

Independent control of all-wheel-drive torque distribution

The sophistication of all-wheel-drive (AWD) technology is approaching the point where the drive torque to each wheel can be independently controlled. This potentially offers vehicle handling enhancements similar to those provided by dynamic stability control, but without the inevitable reduction in vehicle acceleration. Independent control of AWD torque distribution would therefore be especially beneficial under acceleration close to the limit of stability. A vehicle model of a typical sports sedan was developed in Simulink, with fully independent control of torque distribution. Box–Behnken experimental design was employed to determine which torque distribution parameters have the greatest impact on the vehicle course and acceleration. A proportional-integral control strategy was implemented, applying yaw rate feedback to vary the front–rear torque distribution and lateral acceleration feedback to adjust the left–right distribution. The resulting system shows a significant improvement over conventional driveline configurations under aggressive cornering acceleration on a high-μ surface. The performance approaches the theoretical limit for these conditions. In the medium term, such a system is only likely to be economically viable for premium vehicles. However, a future revolution of powertrain technology towards, for example, wheel-mounted motors, could realize these handling benefits far more widely.