Stability control of 4WS vehicles using robust IMC techniques

A robust nonparametric approach to vehicle stability control by means of a four-wheel steer by wire system is introduced. Both yaw rate and sideslip angle feedbacks are used in order to effectively take into account safety as well as handling performances. Reference courses for yaw rate and sideslip angle are computed on the basis of the vehicle speed and the handwheel angle imposed by the driver. An output multiplicative model set is used to describe the uncertainty arising from a wide range of vehicle operating situations. The effects of saturation of the control variables (i.e. front and rear steering angles) are taken into account by adopting enhanced internal model control methodologies in the design of the feedback controller. Actuator dynamics are considered in the controller design. Improvements on understeer characteristics, stability in demanding conditions such as turning on low friction surfaces, damping properties in impulsive manoeuvres, and improved handling in closed loop (i.e. with driver feedback) manoeuvres are shown through extensive simulation results performed on an accurate 14 degrees of freedom nonlinear model, which proved to give good modelling results as compared with collected experimental data.     

Design of a rollover index-based vehicle stability control scheme

This paper presents a rollover index (RI)-based vehicle stability control (VSC) scheme. A rollover index, which indicates an impending rollover, is developed by a roll dynamics phase plane analysis. A model-based roll estimator is designed to estimate the roll angle and roll rate of the vehicle body with lateral acceleration, yaw rate, steering angle and vehicle velocity measurements. The rollover index is computed using an estimated roll angle, estimated roll rate, measured lateral acceleration and time-to-wheel lift. A differential braking control law is designed using a direct yaw control method. The VSC threshold is determined from the rollover index. The effectiveness of the RI, the performance of the estimator and the control scheme are investigated via simulations using a validated vehicle simulator. It is shown that the proposed RI can be a good measure of the danger of rollover and the proposed RI-based VSC scheme can reduce the risk of a rollover.     

Vehicle stability control system for enhancing steerabilty,lateral stability,and roll stability

The Vehicle stability control system is an active safety system designed to prevent accidents from occurring and to stabilize dynamic maneuvers of a vehicle by generating an artificial yaw moment using differential brakes. In this paper, in order to enhance vehicle steerability, lateral stability, and roll stability, each reference yaw rate is designed and combined into a target yaw rate depending on the driving situation. A yaw rate controller is designed to track the target yaw rate based on sliding mode control theory. To generate the total yaw moment required from the proposed yaw rate controller, each brake pressure is properly distributed with effective control wheel decision. Estimators are developed to identify the roll angle and body sideslip angle of a vehicle based on the simplified roll dynamics model and parameter adaptation approach. The performance of the proposed vehicle stability control system and estimation algorithms is verified with simulation results and experimental results.     

A vehicle stability control strategy with adaptive neural network sliding mode theory based on system uncertainty approximation

Modelling uncertainty, parameter variation and unknown external disturbance are the major concerns in the development of an advanced controller for vehicle stability at the limits of handling. Sliding mode control (SMC) method has proved to be robust against parameter variation and unknown external disturbance with satisfactory tracking performance. But modelling uncertainty, such as errors caused in model simplification, is inevitable in model-based controller design, resulting in lowered control quality. The adaptive radial basis function network (ARBFN) can effectively improve the control performance against large system uncertainty by learning to approximate arbitrary nonlinear functions and ensure the global asymptotic stability of the closed-loop system. In this paper, a novel vehicle dynamics stability control strategy is proposed using the adaptive radial basis function network sliding mode control (ARBFN-SMC) to learn system uncertainty and eliminate its adverse effects. This strategy adopts a hierarchical control structure which consists of reference model layer, yaw moment control layer, braking torque allocation layer and executive layer. Co-simulation using MATLAB/Simulink and AMESim is conducted on a verified 15-DOF nonlinear vehicle system model with the integrated-electro-hydraulic brake system (I-EHB) actuator in a Sine With Dwell manoeuvre. The simulation results show that ARBFN-SMC scheme exhibits superior stability and tracking performance in different running conditions compared with SMC scheme.     

基于MPC的分布式驱动越野车辆原地转向控制研究

针对轮毂电机分布式驱动越野车辆在狭小空间快速机动的需求,设计了一种分层结构的原地转向控制策略。基于动力学原理分析了各轮载荷、附着条件对原地转向横摆速度的影响机理,并搭建原地转向运动学模型,上层采用模型预测控制算法设计原地转向理想轨迹以及期望的横摆角速度,开发基于PI滑模控制的横摆运动跟踪算法,通过补偿转向横摆力矩以提高方向角控制的鲁棒性和稳定性,下层以最优轮胎利用率为目标,设计二次规划算法优化分配各轮附加横摆力矩。dSPACE硬件在环测试结果表明,所提出的控制算法可在保证稳定性的前提下实现原地转向,大幅提高了车辆的转向机动性,在方向盘动态输入仿真中,车辆最大转弯半径为0.157 m,转向中心的最大偏移量为3.610 m;同时,驾驶员能对转向过程进行闭环控制,实现了原地转向过程中横摆速度的实时调节。     

Integrated evasive manoeuvre assist for collision mitigation with oncoming vehicles

Development and deployment of steering based collision avoidance systems are made difficult due to the complexity of dealing with oncoming vehicles during the evasive manoeuvre. A method to mitigate the collision risk with oncoming vehicles during such manoeuvres is presented in this work. A point mass analysis of such a scenario is first done to determine the importance of speed for mitigating the collision risk with the oncoming vehicle. A characteristic parameter was identified, which correlates well with the need to increase or decrease speed, in order to reduce the collision risk. This finding was then verified in experiments using a Volvo XC90 test vehicle. A closed-loop longitudinal acceleration controller for collision mitigation with oncoming vehicles is then presented. The longitudinal control is combined with yaw stability control using control allocation to form an integrated controller. Simulations in CarMaker using a validated XC90 vehicle model and the proposed controller showed consistent reductions in the collision risk with the oncoming vehicle.     

Reconfigurable fault-tolerant controller synthesis for a steer-by-wire vehicle using independently driven wheels

In this paper, a synthesis method for a reconfigurable fault-tolerant control system for use in a steer-by-wire vehicle is proposed. The vehicle considered in this paper is also assumed to have independently driven wheels. The control objective in this work is to enable the vehicle yaw rate to track the reference signal even when the steering actuator breaks down. Since the vehicle yaw rate can be controlled with either the front wheel turn angle or the yaw moment generated by the independently driven wheels, this system has actuator redundancy. We attempt to design a control system that manages this actuator redundancy so that the performance degradation due to the actuator failure is minimised. We utilise a control allocator based on on-line optimisation for managing the actuator redundancy. The fault-tolerant control system with a control allocator has several excellent properties. For example, the method can handle various failure situations. Also, since the control allocation problem is reduced to a convex quadratic programming problem, the on-line computational effort is relatively little. However, so far, it has been unclear whether the stability of the control system with the control allocator is guaranteed when the actuator failure occurs. Therefore, we propose a design method of a fault-tolerant controller based on on-line optimisation that guarantees the stability of the overall system. The effectiveness of the method is established through numerical examples.     

基于微分几何的四轮独立驱动车辆运动解耦控制研究

针对车辆在纵向运动和横摆运动时的强耦合关系给车辆动力学控制带来的困难，以四轮独立电驱动车辆作为研究对象，基于微分几何理论设计了车辆系统运动解耦控制方法，将非线性强耦合的四轮驱动车辆动力学系统解耦为纵向和横向两个相对独立运动控制子系统，并设计了鲁棒控制器，以提高抵抗车辆行驶时不确定外力如侧风的干扰能力。基于 Trucksim 软件建立四轮驱动车辆模型，并针对车辆解耦控制策略和抗干扰策略进行了仿真测试。结果表明，相比于无解耦控制的车辆，采用微分几何解耦控制的四轮独立驱动车辆纵向速度偏差降低了 82.1%，横摆角速度偏差降低了80.7%，且微风干扰下的抗干扰能力明显改善，车辆稳定性显著提升。为验证该运动解耦控制策略在实时系统中的控制效果，还进行了硬件在环试验，结果表明，硬件在环试验的结果与仿真结果一致。     

Fault-tolerant yaw moment control with steer — and brake-by-wire devices

This paper presents an fault-tolerant yaw moment control for a vehicle with steer-by-wire (SBW) and brake-by-wire (BBW) devices. SBWs and BBWs can give active front steering (AFS) and electronic stability control (ESC) functions, respectively. Due to motor-driven devices, actuator and sensor faults are inherent in SBW and BBW, and can cause a critical damage to a vehicle. Simple direct yaw moment control is adopted to design a vehicle stability controller. To cope with actuator failure, weighted pseudo-inverse based control allocation (WPCA) with variable weights is proposed in yaw moment distribution procedure. Simulations on vehicle simulation software, CarSim®, show the proposed method is effective for fail safety.     

基于混合仿真技术的车辆横向稳定性控制系统

介绍了利用先进计算机技术和仿真软件，进行车辆横向稳定性控制器设计以及系统混合仿真的过程。首先建立了8自由度车辆动力学系统模型，然后利用前馈补偿和模糊控制策略，设计了车辆横向稳定性控制器。最后对车辆横向稳定性控制系统进行了实时混合仿真研究。仿真结果表明所设计的车辆横向稳定性控制器控制有效，实时性好，而且在道路条件和行驶条件改变时具有较强的适应性和鲁棒性。     

智能汽车轨迹跟踪与横摆稳定性协同控制

为了提高四轮独立驱动智能电动汽车在变曲率弯道下的轨迹跟踪精度和横摆稳定性,提出了一种模型预测控制与直接横摆力矩控制协同的综合控制方法。建立了横纵向耦合的车辆动力学模型,采用2阶龙格库塔离散法保证了离散模型的精度,并基于简化的2自由度动力学模型推导了车辆横摆稳定性约束,设计了非线性模型预测控制器;利用直接横摆力矩控制能够改变车辆横摆角速度和航向角的特点,考虑模型预测控制器的预测状态、控制量以及跟踪误差,设计了协同控制规则。仿真结果表明,协同控制方法解决了考虑横摆稳定性约束的模型预测控制器中存在的稳定性约束与控制精度相矛盾的问题,并补偿了模型预测控制器没有可行解时对横摆稳定性的约束,同时提高了智能汽车的轨迹跟踪精度和横摆稳定性。     

Investigation on evaluation of yaw stability for medium commercial vehicles

This paper proposes test scenarios for evaluation of yaw stability for medium commercial vehicles. Maneuvering, speed, longitudinal tire force, tire-road friction coefficient, road slope, and load condition are considerable factors that have effect on the medium commercial vehicle yaw stability. After conducting an analysis on these six factors, effective test scenarios were developed. A sine with dwell test is well known as a test scenario for evaluation of performance of electronic stability control (ESC) on passenger vehicles and heavy commercial vehicles. The SWD test was modified considering medium commercial vehicle dynamics, and the ramp steer maneuver with maximum acceleration test was proposed. Simulation validation has been conducted using field test data. From simulation study, it was shown that the ESC system for medium commercial vehicle is effectively evaluated by the proposed test scenarios.     

A novel vehicle dynamics stability control algorithm based on the hierarchical strategy with constrain of nonlinear tyre forces

Direct yaw moment control (DYC), which differentially brakes the wheels to produce a yaw moment for the vehicle stability in a steering process, is an important part of electric stability control system. In this field, most control methods utilise the active brake pressure with a feedback controller to adjust the braked wheel. However, the method might lead to a control delay or overshoot because of the lack of a quantitative project relationship between target values from the upper stability controller to the lower pressure controller. Meanwhile, the stability controller usually ignores the implementing ability of the tyre forces, which might be restrained by the combined-slip dynamics of the tyre. Therefore, a novel control algorithm of DYC based on the hierarchical control strategy is brought forward in this paper. As for the upper controller, a correctional linear quadratic regulator, which not only contains feedback control but also contains feed forward control, is introduced to deduce the object of the stability yaw moment in order to guarantee the yaw rate and side-slip angle stability. As for the medium and lower controller, the quantitative relationship between the vehicle stability object and the target tyre forces of controlled wheels is proposed to achieve smooth control performance based on a combined-slip tyre model. The simulations with the hardware-in-the-loop platform validate that the proposed algorithm can improve the stability of the vehicle effectively.     

独立轮电驱动车辆主动操纵稳定控制研究

提出了采用变增益参考模型的滑模跟踪控制策略,以横摆角速度和侧滑速度为控制对象,独立控制左右轮驱动力产生直接横摆力矩,提高了车辆在极限工况下的操纵稳定性,并改善了车辆固有的转向特性。改进的滑模控制算法减小了系统抖振并具有较强的鲁棒性。     

直接横摆力矩控制车辆稳定性研究概述

针对直接横摆力矩如何实现汽车的稳定性,与其他一些汽车稳定性控制系统进行了比较。概述了国内外采用的一些直接横摆力矩控制策略及力矩分配方法,并介绍了直接横摆力矩控制在实车上的应用,最后分析了直接横摆力矩的发展趋势。     

A Fuzzy Logic Direct Yaw-Moment Control System for All-Wheel-Drive Electric Vehicles

Summary In-wheel-motors are revolutionary new electric drive systems that can be housed in vehicle wheel assemblies. Such E-wheels permit packaging flexibility by eliminating the central drive motor and the associated transmission and driveline components, including the transmission, the differential, the universal joints and the drive shaft. Apart from many advantages of such a system, unequalled independent wheel control allows vehicle dynamic improvement to assist the driver in enhancing cornering and straight-line stability on slippery roads and in adverse ground conditions. In this paper a Fuzzy logic driver-assist stability system for all-wheel-drive electric vehicles based on a yaw reference DYC is introduced. The system assists the driver with path correction, thus enhancing cornering and straight-line stability and providing enhanced safety. A feed-forward neural network is employed to generate the required yaw rate reference. The neural net maps the vehicle speed and the steering angle to give the yaw rate reference. The vehicle true speed is estimated using a multi-sensor data fusion method. Data from wheel sensors and an embedded accelerometer are fed into an estimator, where a Fuzzy logic system decides which input is more reliable. The efficiency of the proposed system is approved by conducting a computer simulation. The proposed control system is an effective and easy to implement method to enhance the stability of all-wheel-drive electric vehicles.     

A Fuzzy Logic Direct Yaw-Moment Control System for All-Wheel-Drive Electric Vehicles

Summary In-wheel-motors are revolutionary new electric drive systems that can be housed in vehicle wheel assemblies. Such E-wheels permit packaging flexibility by eliminating the central drive motor and the associated transmission and driveline components, including the transmission, the differential, the universal joints and the drive shaft. Apart from many advantages of such a system, unequalled independent wheel control allows vehicle dynamic improvement to assist the driver in enhancing cornering and straight-line stability on slippery roads and in adverse ground conditions. In this paper a Fuzzy logic driver-assist stability system for all-wheel-drive electric vehicles based on a yaw reference DYC is introduced. The system assists the driver with path correction, thus enhancing cornering and straight-line stability and providing enhanced safety. A feed-forward neural network is employed to generate the required yaw rate reference. The neural net maps the vehicle speed and the steering angle to give the yaw rate reference. The vehicle true speed is estimated using a multi-sensor data fusion method. Data from wheel sensors and an embedded accelerometer are fed into an estimator, where a Fuzzy logic system decides which input is more reliable. The efficiency of the proposed system is approved by conducting a computer simulation. The proposed control system is an effective and easy to implement method to enhance the stability of all-wheel-drive electric vehicles.     

Pivot point-based control for active rear-wheel steering in passenger vehicles

This paper presents a new application of active rear-wheel steering control to improve the lateral vehicle behaviour. In the state of the art, yaw or lateral velocity is used as control variable that means one degree of freedom being not directly controlled. A worse subjective impressions due to movements in the rear end of the vehicle during strong counter-steering are a consequence. To avoid this effect in urban surroundings, an innovative structure to control the pivot point distance of the vehicle is proposed. In this case the coupled elementary states yaw and lateral velocity can be influenced based on a higher level criteria. Analysis show that pivot point fixing provides a comprehensible reference behaviour. Solving the issue of singularity during disappearing yaw movement is the basis to design a performant modified feedforward input–output linearisation. An analytic stability analysis of the internal dynamics shows system immanent limitations which do not influence the target of improving the lateral vehicle dynamics in urban manoeuvres. Finally, the advantages of pivot-based control are highlighted by a comparison with state of the art rear axle control.     

Development of an active front steering (AFS) system with QFT control

This paper investigates an active front steering control strategy based on quantitative feedback theory (QFT). By incorporating feedback from a yaw rate sensor into the active steering system, the control system improves the dynamic response of the vehicle. The steering response of a vehicle generally depends upon uncertain quantities like mass, velocity, and road conditions. Thus, QFT is used to design a controller with robust performance. A multi-degree-of-freedom nonlinear model is co-simulated here by MATLAB Simulink and ADAMS/CAR. The performance of the control system is evaluated under various emergency maneuvers and road conditions. The result shows that the designed robust control system has good control performance and can efficiently improve handing qualities and stability characteristics.     

基于驾驶人转向意图的双电机驱动电动汽车稳定性控制策略

为了使双电机驱动电动车在车辆稳定性控制过程中能够精确解读驾驶意图,使车辆实际行驶状态与驾驶意图期望的车辆行驶状态尽可能相符合,提出一种基于驾驶人意图辨识的稳定性控制策略.利用基于支持向量机递归特征消除(SVM-RFE)得到的特征参数构建基于长短期记忆(LSTM)模型的驾驶人转向意图辨识模型;基于转向意图识别结果,以方向...