Comparison of Feedforward and Feedback Control for 4WS

A system incorporating feedforward plus feedback control was configured such that it would follow the target yaw rate found by calculation. Selection of optimum values for the control system constants made it possible to separate control of the steering input response characteristic from control of vehicle stability against external disturbances. The former is controlled by the feedforward control function and the latter by the feedback control function; the values of the two functions can be set independently.     

Additional 4WS and Driver Interaction

SUMMARY

This investigation is based on a complex 4-wheel vehicle model of a passenger car that includes steering system and drive train. The tyre properties are described for all possible combined longitudinal and lateral slip values and for arbitrary friction conditions. The active part is an additional steering system of all 4 wheels, additionally to the driver's steering wheel angle input. Three control levels are used for the driver model that thereby can follow a given trajectory or avoid an obstacle.

The feedback control of the additional 4 wheel steering is based on an observer which can also have adaptive characteristics. Moreover a virtual vehicle model in a feedforward scheme can provide desired steering characteristics.

To get information for critical situations a cornering manoeuvre with sudden u-split conditions is simulated. Further a similar manoeuvre is used to evaluate the reentry in a high friction area from low friction conditions. And finally the performance of the controller is shown in a severe lane change manoeuvre.     

The Application of Linear Optimal Control Theory to the Design of Active Automotive Suspensions

SUMMARY

Some linear stochastic control theory relevant to the design of active suspension systems subject to integrated or filtered white noise excitation is reviewed, and application of the theory to a particular problem is considered. The problem considered is the well known quarter car problem in which a control law which minimises a performance function representing passenger discomfort, suspension working space, and tyre load fluctuations is required. With full state feedback, the requirement for a formulation of the problem which leads to the system under consideration being observable and controllable is referred to, and it is shown how a well known coordinate transformation enables this requirement to be satisfied. With limited state (or output) feedback, problem formulations which will avoid potential numerical problems in deriving the optimal control are described. Example solutions are included in order to illustrate the methods.     

Crosswind Feedforward Control – A Measure to Improve Vehicle Crosswind Behaviour

SUMMARY

The theory of crosswind feedforward control was explained using the example of a vehicle with active front-wheel steering. Beforehand, the calculation formulas and frequency responses of the transient crosswind force and of the wind yaw moment acting on the vehicle were derived using the example of a simple vehicle fluid model. The influence of the transiency of crosswind disturbance on the dynamic crosswind behaviour of a vehicle was then presented. The results of simulation confirmed the analyses carried out in the frequency domain for feedforward control with front, rear and all-wheel steering. With front-wheel steering, the influence of crosswind on one of the vehicle movement variables (lateral acceleration or yaw rate) could be almost completely compensated by dynamic feedforward control. With rear-wheel steering, it is only possible to compensate directly for the influence on the yawing rate. Due to the setting of the side force in the same direction as the lateral wind force at the start, active rear-wheel steering is not so successful as active front-wheel steering. Nevertheless, the crosswind behaviour of a vehicle can be considerably enhanced by feedforward control with rear-wheel steering. The best crosswind behaviour was obtained with active all-wheel steering: the vehicle hardly responds at all to crosswinds and remains on course despite heavy gusts of wind.     

Nonlinear feedforward–feedback control of clutch-to-clutch shift technique

To improve the shift quality of the vehicle with clutch-to-clutch gear shifts, a nonlinear feedforward–feedback control scheme is proposed for clutch slip control during the shift inertia phase. The feedforward control is designed based on flatness in consideration of the system nonlinearities, and the linear feedback control is given to accommodate the model errors and the disturbances. Lookup tables, which are widely used to represent complex nonlinear characteristics of powertrain systems, appear in their original form in the designed feedforward controller, while the linear feedback controller is calculated through linear matrix inequalities such that the control system is robust against the parameter uncertainties. Finally, the designed controller is tested on an AMESim powertrain simulation model, which contains a time-variant model of clutch actuators.     

Actuator optimal placement studies of high-speed power bogie for active hunting stability

ABSTRACT

We put forward three actuator placements of the high-speed train power bogie to improve the train hunting stability. The active control forces act on the frame, between the frame and the motor, and on the motor by the inertial or retractable actuator, respectively, based on the feedback states of vibration velocity of the front and rear end beams. The feedback gains and the motor suspension parameters in different cases are optimised with the two objectives of system stability margin and control effort. The required actuator outputs of the three cases are compared based on the theoretical analysis with a 8 DOF bogie model. The results show that the three control cases can effectively improve the hunting stability, especially at high speed. The active control of motor lateral movement is helpful to increase the dynamic vibration absorbing function of the motor flexible suspension, and the control output is obviously smaller than the other two control cases. In addition, the influence of system delay on stability was analysed and we could use or avoid the effects of delay on the stability.     

某电动车后轮转向系统控制策略开发研究

利用某电动车线性二自由度车辆模型和基于CarSim与MATLAB/Simulink的联合仿真模型,对所提出的后轮转向双参前馈控制策略进行仿真分析,并与前馈比例控制策略、前馈比例加横摆角速度反馈控制策略的控制效果进行对比分析,证明了双参前馈控制策略的有效性。     

Design of Optimal Four-Wheel Steering System

SUMMARY

Optimal design of the four wheel steering (4WS) system of the ground vehicle is studied. 4WS vehicles with the optimal control scheme are considered first. General formulation of the optimal control law is developed based on the linear quadratic regulator theory. The vehicle speed function (VSF) based 4WS vehicle with a simple feedback controller is considered as a special case of the optimal system. Two new designs of the VSF 4WS system are proposed and their performances are compared with the optimal 4WS systems and the existing VSF 4WS system. The first system is designed for the maximum stability while the second system is designed to emulate the response of the optimal 4WS vehicle. Advantages of the new VSF designs are discussed.     

Theoretical Limitations in Active Vehicle Suspensions

SUMMARY

Vehicle suspensions in which forces are generated in response to feedback signals by active elements obviously offer increased design flexibility compared to conventional suspensions using passive elements such as springs and dampers. It is often assumed that if practical difficulties are neglected, active systems could in principle produce arbitrary ideal, behavior. It is shown, using a simple linear two degree-of-freedom suspension system, model that even using complete state feed back and in the case of in which the system is controllable in the control theory sense, there still are limitations to suspension performance in the fully active case. If the ideal suspension performance is defined based on low-pass filtering of roadway unevenness inputs, an active suspension may not offer much better performance than a partially active or adaptive passive suspension depending upon the values of certain vehicle parameters.     

Adaptive Yaw Rate Feedback 4WS with Tire/Road Friction Coefficient Estimator

This paper proposes an adaptive yaw rate feedback control system for a four-wheel-steering (4WS) vehicle which involves a tire/road friction coefficient estimator. The adaptive 4WS system has been developed so that the vehicle possesses desirable lateral characteristics even on slippery roads and in critical driving situations. The friction coefficient is estimated on real time from the yaw rate response of the controlled vehicle with the least squares. The control system adopts a two degree of freedom structure which consists of a feedforward compensator and a feedback control subsystem. The feedforward compensator is determined with the estimated friction coefficient to minimize the steady-state and transient vehicle slip angle in spite of changes in tire/road conditions. The feedback subsystem adopts the Internal Model Control (IMC) structure in order to compensate for nonlinearities and to realize robustness against modelling and estimation errors.     

Active Suspensions Based on Fast Load Levelers

SUMMARY

A class of active suspensions is presented which provides near optimum isolation of base motion as well as zero static deflection for force disturbances using a simple type of feedback. The load leveling effect is rapid with the system stabilized using isolated mass velocity feedback both for a semi-active damper and for the load leveler. The system can be made energy conservative and fail safe since the system reverts to a reasonable passive isolator if the load leveling effect and even if the active damping effect is switched off. The system could be incorporated in automotive vehicles with some extension of the feedback control to account for several aspects of body motion.     

Analyses of Vision-based Lateral Control for Automated Highway System

SUMMARY

The stability and performance of a vision-based vehicle lateral control system are analyzed. Effects of look-ahead distance, vision delay, and vehicle speed on the performance of vision feedback control system are examined by using frequency domain and time domain methods. A measurement model of the vision system is derived from the point of view of multiple sensors. The quantization error of the vision system is analyzed and the way of extracting essential information for control is studied. Based on this analysis, some guidelines for the design of vision-based controllers are proposed. A design example is further illustrated for a vision system with a substantial time delay.     

An Active Pantograph with Shaped Frequency Response Employing Linear Output Feedback Control

SUMMARY

In pantographs used for current collection on high speed electric trains it is desirable to minimise the fluctuations in the contact force between the collector head and the catenary. A simple two-mass linear model is employed for the pantograph and the design of the proposed control system is based on the input admittance at low frequencies. Frequency shaping is incorporated in the performance index, and a simple dynamic controller is employed to achieve optimality in an equivalent transformed system, while minimising the number of feedback quantities to be measured. A significant reduction in the average contact force appears possible.     

An H2 Formulation for the Design of a Passive Vibration-Isolation System for Cars

SUMMARY

Optimal design of an active suspension system for road vehicles can be solved using LQR techniques. Such a problem is equivalent, in the frequency domain, to determine the state feedback gain matrix that minimizes the H₂ norm of a suitable transfer matrix.

A passive suspension system can be seen as the physical realization of a suitable state feedback law whose gains are function of the system parameters. This law, and thus the characteristic elements of the passive suspension, can be determined as an approximation of the H₂ optimal solution. This methodology allows one to choose the best controller from a constrained subset (i.e., all possible passive suspensions of a particular form) of all possible controllers.     

DISCUSSION NOTE on Karnopp's article “Active Damping in Road Vehicle Suspension Systems”

SUMMARY

In this paper, an optimal suspension system is derived for a quarter-car model using multivariable integral control. The suspension system features two parts. The first part is an integral control acting on suspension deflection to ensure zero steady-sate offset due to body and maneuvering forces as well as road inputs. The second is a proportional control operating on the vehicle system states for vibration control and performance improvement. The optimal ride performance of the active suspensions based on linear full-state feedback control laws with and without integral control together with the performance of passive suspensions are compared.     

Integrated Control of Active Rear Wheel Steering and Direct Yaw Moment Control

SUMMARY

An integrated control system of active rear wheel steering (4WS) and direct yaw moment control (DYC) is presented in this paper. Because of the tire nonlinearity that is mainly due to the saturation of cornering forces, vehicle handling performance is improved but limited to a certain extent only by steering control. Direct yaw moment control using braking and/or driving forces is effective not only in linear but also nonlinear ranges of tire friction circle. The proposed control system is a model matching controller which makes the vehicle follow the desired dynamic model by the state feedback of both yaw rate and side slip angle. Various computer simulations are carried out and show that vehicle handling performance is much improved by the integrated control system.     

The Response of Active and Semi-active Suspensions to Realistic Feedback Signals

SUMMARY

A simple vehicle model is presented incorporating passive, active, and semi-active suspensions. When the desired feedback variables are ideally available, the system response is well understood and excellent sprung mass isolation results. More often than not, the measured variables must be signal processed in some manner prior to their use in some control algorithm. This paper presents the expected response of a simple vehicle with an active and/or semi-active suspension, subject to non-ideal feedback information.     

The Chatter of Semi-Active On-Off Suspensions and its Cure

ABSTRACT

Semi-active suspensions are those in which otherwise passively generated damper forces are modulated using feedback control and small amounts of control effort. Recently it was discovered that two-stage, ON-OFF, semi-active control would chatter between the ON and OFF states in a manner similar to bang-bang, active control systems. This chatter is dependent upon the switching algorithm. This paper describes the dynamics of this chatter and suggests alternative control policies for its cure.     

Active Roll Control for Passenger Cars

SUMMARY

The development of a mathematical model of a limited bandwidth hydro-pneumatic suspension that is incorporated into a vehicle handling model is described. The combined model is used to evaluate a suitable control strategy for eliminating body roll during a cornering manoeuvre. The philosophy behind the roll control strategy has been to use feedback measurements of the body motions which do not compromise the ride control. A study of the influence of the position of the body motion feedback transducer on the effectiveness of the system to reduce the body roll is presented. Non-linear modelling of the suspension components for a 0.8g cornering manoeuvre has revealed performance limitations. Conclusions are drawn as to the effectiveness of the control scheme.     

An Advanced Steering System with Active Kinesthetic Feedback for Handling Qualities Improvement

SUMMARY

Advanced Steering System with artificial steering wheel torque-active kinesthetic information feedback for improving handling qualities is discussed. Fundamentally the structure of the system may be considered to another form of model following control. In this system, a driver always remains in the control loop and receives steering control information which give him/her a direct hint to steer a steering wheel. This system works as a stability and control augmentation system of the vehicle to improve the vehicle handling qualities both in compensatory and pursuit control task, and is expected to reduce driver's workload. Effects of this system are analyzed in terms of man-machine system characteristics. Identification of driver dynamics was carried out to find why such improvement could be achieved. Availability of the proposed system is verified by analysis, simulator and proving ground tests.