A path-following driver–vehicle model with neuromuscular dynamics,including measured and simulated responses to a step in steering angle overlay

An existing driver–vehicle model with neuromuscular dynamics is improved in the areas of cognitive delay, intrinsic muscle dynamics and alpha–gamma co-activation. The model is used to investigate the influence of steering torque feedback and neuromuscular dynamics on the vehicle response to lateral force disturbances. When steering torque feedback is present, it is found that the longitudinal position of the lateral disturbance has a significant influence on whether the driver’s reflex response reinforces or attenuates the effect of the disturbance. The response to angle and torque overlay inputs to the steering system is also investigated. The presence of the steering torque feedback reduced the disturbing effect of torque overlay and angle overlay inputs. Reflex action reduced the disturbing effect of a torque overlay input, but increased the disturbing effect of an angle overlay input. Experiments on a driving simulator showed that measured handwheel angle response to an angle overlay input was consistent with the response predicted by the model with reflex action. However, there was significant intra- and inter-subject variability. The results highlight the significance of a driver’s neuromuscular dynamics in determining the vehicle response to disturbances.     

Risk management algorithm for rear-side collision avoidance using a combined steering torque overlay and differential braking

This paper describes a risk management algorithm for rear-side collision avoidance. The proposed risk management algorithm consists of a supervisor and a coordinator. The supervisor is designed to monitor collision risks between the subject vehicle and approaching vehicle in the adjacent lane. An appropriate criterion of intervention, which satisfies high acceptance to drivers through the consideration of a realistic traffic, has been determined based on the analysis of the kinematics of the vehicles in longitudinal and lateral directions. In order to assist the driver actively and increase driver's safety, a coordinator is designed to combine lateral control using a steering torque overlay by motor-driven power steering and differential braking by vehicle stability control. In order to prevent the collision while limiting actuator's control inputs and vehicle dynamics to safe values for the assurance of the driver's comfort, the Lyapunov theory and linear matrix inequalities based optimisation methods have been used. The proposed risk management algorithm has been evaluated via simulation using CarSim and MATLAB/Simulink.     

A model of driver steering control incorporating the driver's sensing of steering torque

Steering feel, or steering torque feedback, is widely regarded as an important aspect of the handling quality of a vehicle. Despite this, there is little theoretical understanding of its role. This paper describes an initial attempt to model the role of steering torque feedback arising from lateral tyre forces. The path-following control of a nonlinear vehicle model is implemented using a time-varying model predictive controller. A series of Kalman filters are used to represent the driver's ability to generate estimates of the system states from noisy sensory measurements, including the steering torque. It is found that under constant road friction conditions, the steering torque feedback reduces path-following errors provided the friction is sufficiently high to prevent frequent saturation of the tyres. When the driver model is extended to allow identification of, and adaptation to, a varying friction condition, it is found that the steering torque assists in the accurate identification of the friction condition. The simulation results give insight into the role of steering torque feedback arising from lateral tyre forces. The paper concludes with recommendations for further work.     

Influencing driver chosen cornering speed by means of modified steering feel

This paper presents an investigation about influencing the driver's behaviour intuitively by means of modified steering feel. For a rollover indication through haptic feedback a model was developed and tested that returned a warning to the driver about too high vehicle speed. This was realised by modifying the experienced steering wheel torque as a function of the lateral acceleration. The hypothesis for this work was that drivers of heavy vehicles will perform with more margin of safety to the rollover threshold if the steering feel is altered by means of decreased or additionally increased steering wheel torque at high lateral acceleration. Therefore, the model was implemented in a test truck with active steering with torque overlay and used for a track test. Thirty-three drivers took part in the investigation that showed, depending on the parameter setting, a significant decrease of lateral acceleration while cornering.     

Haptic steering support for driving near the vehicle’s handling limits; skid-pad case

Current vehicle dynamic control systems from simple yaw control to high-end active steering support systems are designed to primarily actuate on the vehicle itself, rather than stimulate the driver to adapt his/her inputs for better vehicle control. The driver though dictates the vehicle’s motion, and centralizing him/her in the control loop is hypothesized to promote safety and driving pleasure. Exploring the above statement, the goal of this study is to develop and evaluate a haptic steering support when driving near the vehicle’s handling limits (Haptic Support Near the Limits; HSNL). The support aims to promote the driver’s perception of the vehicle’s behaviour and handling capacity (the vehicle’s internal model) by providing haptic (torque) cues on the steering wheel. The HSNL has been evaluated in (a) driving simulator tests and (b) tests with a vehicle (Opel Astra G/B) equipped with a variable steering feedback torque system. Drivers attempted to achieve maximum velocity while trying to retain control in a circular skid-pad. In the simulator (a) 25 subjects drove a vehicle model parameterised as the Astra on a dry skid-pad while in (b) 17 subjects drove the real Astra on a wet skid-pad. Both the driving simulator and the real vehicle tests led to the conclusion that the HSNL assisted subjects to drive closer to the designated path while achieving effectively the same speed. With the HSNL the drivers operated the tires in smaller slip angles and hence avoided saturation of the front wheels’ lateral forces and excessive understeer. Finally, the HSNL reduced their mental and physical demand.     

Steering disturbance rejection using a physics-based neuromusculoskeletal driver model

The aim of this work is to develop a comprehensive yet practical driver model to be used in studying driver–vehicle interactions. Drivers interact with their vehicle and the road through the steering wheel. This interaction forms a closed-loop coupled human–machine system, which influences the driver's steering feel and control performance. A hierarchical approach is proposed here to capture the complexity of the driver's neuromuscular dynamics and the central nervous system in the coordination of the driver's upper extremity activities, especially in the presence of external disturbance. The proposed motor control framework has three layers: the first (or the path planning) plans a desired vehicle trajectory and the required steering angles to perform the desired trajectory; the second (or the musculoskeletal controller) actuates the musculoskeletal arm to rotate the steering wheel accordingly; and the final layer ensures the precision control and disturbance rejection of the motor control units. The physics-based driver model presented here can also provide insights into vehicle control in relaxed and tensed driving conditions, which are simulated by adjusting the driver model parameters such as cognition delay and muscle co-contraction dynamics.     

Disturbance compensation with a torque controllable steering system

Via a conventional steering system the driver perceives desired and disturbing effects such as road feedback and resonance effects, respectively. They appear with overlapping frequency spectra within the driver's steering torque. This paper introduces a control algorithm that is suppressing periodic disturbances without affecting useful steering road feedback attributes as well as regular power assistance characteristic. This is realised by an integrated torque actuator within the steering column in conjunction with a conventional Hydraulic-assisted Power Steering (HPS) system.     

Advanced emergency braking under split friction conditions and the influence of a destabilising steering wheel torque

The steering system in most heavy trucks is such that it causes a destabilising steering wheel torque when braking on split friction, that is, different friction levels on the two sides of the vehicle. Moreover, advanced emergency braking systems are now mandatory in most heavy trucks, making vehicle-induced split friction braking possible. This imposes higher demands on understanding how the destabilising steering wheel torque affects the driver, which is the focus here. Firstly, an experiment has been carried out involving 24 subjects all driving a truck where automatic split friction braking was emulated. Secondly, an existing driver–vehicle model has been adapted and implemented to improve understanding of the observed outcome. A common conclusion drawn, after analysing results, is that the destabilising steering wheel torque only has a small effect on the motion of the vehicle. The underlying reason is a relatively slow ramp up of the disturbance in comparison to the observed cognitive delay amongst subjects; also the magnitude is low and initially suppressed by passive driver properties.     

Lateral handling improvement with dynamic curvature control for an independent rear wheel drive EV

The integrated longitudinal and lateral dynamic motion control is important for four wheel independent drive (4WID) electric vehicles. Under critical driving conditions, direct yaw moment control (DYC) has been proved as effective for vehicle handling stability and maneuverability by implementing optimized torque distribution of each wheel, especially with independent wheel drive electric vehicles. The intended vehicle path upon driver steering input is heavily depending on the instantaneous vehicle speed, body side slip and yaw rate of a vehicle, which can directly affect the steering effort of driver. In this paper, we propose a dynamic curvature controller (DCC) by applying a the dynamic curvature of the path, derived from vehicle dynamic state variables; yaw rate, side slip angle, and speed of a vehicle. The proposed controller, combined with DYC and wheel longitudinal slip control, is to utilize the dynamic curvature as a target control parameter for a feedback, avoiding estimating the vehicle side-slip angle. The effectiveness of the proposed controller, in view of stability and improved handling, has been validated with numerical simulations and a series of experiments during cornering engaging a disturbance torque driven by two rear independent in-wheel motors of a 4WD micro electric vehicle.     

An Advanced Steering System with Active Kinesthetic Feedback for Handling Qualities Improvement

SUMMARY

Advanced Steering System with artificial steering wheel torque-active kinesthetic information feedback for improving handling qualities is discussed. Fundamentally the structure of the system may be considered to another form of model following control. In this system, a driver always remains in the control loop and receives steering control information which give him/her a direct hint to steer a steering wheel. This system works as a stability and control augmentation system of the vehicle to improve the vehicle handling qualities both in compensatory and pursuit control task, and is expected to reduce driver's workload. Effects of this system are analyzed in terms of man-machine system characteristics. Identification of driver dynamics was carried out to find why such improvement could be achieved. Availability of the proposed system is verified by analysis, simulator and proving ground tests.     

Application of rack type motor driven power steering control system for heavy vehicles

The Electric Power Steering (EPS) or Motor Driven Power Steering (MDPS) mechanism proves to be a bright prospect among passenger vehicles ensuring better vehicle safety and fuel economy. The car manufacturers are focusing on the production of Rack type EPS system (REPS). This paper describes the development of concurrent simulation technique using TruckSim and control strategy for analysing RMDPS control system with a dynamic vehicle system. A full Truck vehicle model interacting with RMDPS control algorithm was concurrently simulated on a sinusoidal steering input. The dynamic responses of vehicle chassis and steering system resulting were evaluated and compared with proving ground experimental data. The comparisons show reasonable agreement on steering wheel torque, lateral acceleration and yaw rate. This concurrent simulation research leads the possibility of RMDPS performance evaluation of Truck and Semi-bonnet cars.     

Measurement and mathematical model of a driver's intermittent compensatory steering control

The compensatory (feedback) component of a human driver's steering control is examined. In particular, the effect of the cognitive process is studied. Model predictive control theory is used to implement models of intermittency in cognitive processing. Experiments using a fixed-base driving simulator with periodic occlusion of the visual display are used to reveal the nature of the driver's steering behaviour. An intermittent serial-ballistic control strategy is found to match the measured behaviour better than intermittent zero-order hold or continuous control. The findings may enable some insight to driver-vehicle interaction and vehicle handling qualities.     

电子差速系统轮胎附着特性模拟仿真研究

电子差速系统相对于传统的机械式差速器可以实现转矩的精准分配,根据轮胎的纵向运动特性以及侧向运动特性,结合轮胎滑移率让内外侧车轮在过弯时拥有足够的附着力,减小整车的横摆角速度,提高过弯稳定性。采用后轮双电机的驱动方案,驱动电机采用直接转矩控制的方法,由整车控制器将指定的计算转矩信号发送给电机控制器完成动力分配,所需转矩根据驾驶员的加速踏板及方向盘转角,运用阿克曼转向模型计算得到。     

Driver steering and muscle activity during a lane-change manoeuvre

The article reports an experimental study of driver steering control behaviour in a lane-change manoeuvre. Eight test subjects were instrumented with electromyography to measure muscle activation and co-contraction. Each subject completed 30 lane-change manoeuvres with one vehicle on a fixed-base driving simulator. For each driver, the steering torque feedback characteristic was changed after every ten manoeuvres; the response of the vehicle to steering angle inputs was not changed. Drivers' control strategies were found to be robust to changes in steering torque feedback. Path-following errors, muscle activity and muscle co-contraction all reduce with the number of lane-changes performed by the driver, suggesting the existence of a learning process. Comparing the test subjects, there was some evidence that high levels of co-contraction were used to allow high-frequency steering inputs to be generated. The results contribute to the understanding of vehicle-driver (and more generally, human-machine) dynamic interaction.     

Driver steering and muscle activity during a lane-change manoeuvre

The article reports an experimental study of driver steering control behaviour in a lane-change manoeuvre. Eight test subjects were instrumented with electromyography to measure muscle activation and co-contraction. Each subject completed 30 lane-change manoeuvres with one vehicle on a fixed-base driving simulator. For each driver, the steering torque feedback characteristic was changed after every ten manoeuvres; the response of the vehicle to steering angle inputs was not changed. Drivers' control strategies were found to be robust to changes in steering torque feedback. Path-following errors, muscle activity and muscle co-contraction all reduce with the number of lane-changes performed by the driver, suggesting the existence of a learning process. Comparing the test subjects, there was some evidence that high levels of co-contraction were used to allow high-frequency steering inputs to be generated. The results contribute to the understanding of vehicle–driver (and more generally, human–machine) dynamic interaction.     

A passenger car driver model for higher lateral accelerations

Due to increasing demands for time and cost efficient vehicle and driver assistant systems development, numerical simulation of closed-loop manoeuvres becomes increasingly important. Thus, the driver has to be considered in the modelling. On the basis of a two-layer approach to model a driver's steering behaviour, the field of application is extended to higher lateral accelerations in this study. An analytical method to determine the driver parameters is presented, which is based on the two-wheel vehicle model. The simulation results are determined using a full vehicle model including all essential nonlinearities. Standard manoeuvres in the nonlinear range of vehicle handling behaviour are performed. A cornering manoeuvre is chosen to show the characteristics of the proposed driver model.     

Advanced Steering System Adaptable to Lateral Control Task and Driver's Intention

This paper proposes an advanced steering system that adaptively varies the static gain and dynamics of the steering system. The steering system gain is adjusted, depending on whether the driver is in an aggressive or leisurely driving mood. The steering system dynamics is so designed that the command mode of the steering system will be either a rate-command or an attitude-command according to the lateral control task performed by the driver. The recognition system for lateral control tasks, a lane-following or lane-change task is proposed. The findings of simulator tests indicate proposed advanced steering system would remarkably improve the vehicle handling qualities.     

A novel integrated chassis controller for full drive-by-wire vehicles

In this paper, a systematic design with multiple hierarchical layers is adopted in the integrated chassis controller for full drive-by-wire vehicles. A reference model and the optimal preview acceleration driver model are utilised in the driver control layer to describe and realise the driver's anticipation of the vehicle's handling characteristics, respectively. Both the sliding mode control and terminal sliding mode control techniques are employed in the vehicle motion control (MC) layer to determine the MC efforts such that better tracking performance can be attained. In the tyre force allocation layer, a polygonal simplification method is proposed to deal with the constraints of the tyre adhesive limits efficiently and effectively, whereby the load transfer due to both roll and pitch is also taken into account which directly affects the constraints. By calculating the motor torque and steering angle of each wheel in the executive layer, the total workload of four wheels is minimised during normal driving, whereas the MC efforts are maximised in extreme handling conditions. The proposed controller is validated through simulation to improve vehicle stability and handling performance in both open- and closed-loop manoeuvres.     

基于功能安全的分布式驱动电动汽车前轮失效补偿控制

分布式驱动电动汽车可以实现四轮转矩分配和差动转向,提升整车的动力学控制性能和经济性,但是四轮转矩独立可控的特点也对功能安全提出挑战.当前轮单侧电机出现执行器故障失效情况时,不仅会产生附加横摆力矩降低车辆安全性,差动转向功能的存在还会使车辆严重偏航.基于此,在设计分布式驱动-线控转向一体化底盘的基础上,基于功能安全提出一...     

基于人机共驾的车道保持辅助控制系统研究（双语出版）

车道保持控制系统是汽车安全辅助驾驶的重要组成部分，可有效提高汽车主动安全性、避免车辆无意识地偏离本车道。目前，大部分车道保持控制系统在工作时将驾驶人的操作视为外界干扰，没有考虑人机共驾阶段下驾驶人与控制系统的控制权分配问题，易造成人机冲突、影响驾驶人的驾驶感受。论文兼顾驾驶人与辅助控制系统各自优势，基于人机共驾技术对车道保持控制系统进行研究。构建基于安全行驶区域与最晚预警边界相结合的车道偏离决策模型，在保证其预警精度的同时降低计算复杂性，根据车辆行驶状态和路面附着系数动态调整预警阈值；研究串级MPC-PID控制策略实现对车辆横向位置的控制，将最优问题转化为二次规划求得目标前轮转角，利用PID算法完成对目标前轮转角的跟踪；引入共驾系数对车辆的控制权进行分配，研究共驾系数分配模型，以车辆状态误差和驾驶人转向力矩作为模糊控制的输入变量、共驾系数作为输出变量，降低辅助控制系统与驾驶人之间的冲突；最后，利用CarSim与Simulink联合仿真对所研究的控制策略进行仿真验证，结果表明共驾系数能够根据驾驶人的操作和车辆运行状态的变化实现动态调整，辅助控制力矩与驾驶人输入力矩变化趋势相同，在保留驾驶人一定操作的基础下可避免车辆偏离车道、降低人机冲突。