An ABS control logic based on wheel force measurement

The paper presents an anti-lock braking system (ABS) control logic based on the measurement of the longitudinal forces at the hub bearings. The availability of force information allows to design a logic that does not rely on the estimation of the tyre–road friction coefficient, since it continuously tries to exploit the maximum longitudinal tyre force.

The logic is designed by means of computer simulation and then tested on a specific hardware in the loop test bench: the experimental results confirm that measured wheel force can lead to a significant improvement of the ABS performances in terms of stopping distance also in the presence of road with variable friction coefficient.     

Experimental investigations on continuous regenerative anti-lock braking system of full electric vehicle

Functions of anti-lock braking for full electric vehicles (EV) with individually controlled wheel drive can be realized through conventional brake system actuating friction brakes and regenerative brake system actuating electric motors. To analyze advantages and limitations of both variants of anti-lock braking systems (ABS), the presented study introduces results of experimental investigations obtained from proving ground tests of all-wheel drive EV. The brake performance is assessed for three different configurations: hydraulic ABS; regenerative ABS only on the front axle; blended hydraulic and regenerative ABS on the front axle and hydraulic ABS on the rear axle. The hydraulic ABS is based on a rule-based controller, and the continuous regenerative ABS uses the gain-scheduled proportional-integral direct slip control with feedforward and feedback control parts. The results of tests on low-friction road surface demonstrated that all the ABS configurations guarantee considerable reduction of the brake distance compared to the vehicle without ABS. In addition, braking manoeuvres with the regenerative ABS are characterized by accurate tracking of the reference wheel slip that results in less oscillatory time profile of the vehicle deceleration and, as consequence, in better driving comfort. The results of the presented experimental investigations can be used in the process of selection of ABS architecture for upcoming generations of full electric vehicles with individual wheel drive.     

Cooperative control of the motor and the electric booster brake to improve the stability of an in-wheel electric vehicle

A cooperative control algorithm for an in-wheel motor and an electric booster brake is proposed to improve the stability of an in-wheel electric vehicle. The in-wheel system was modeled by dividing it into motor and mechanical parts, and the electric booster brake was modeled through tests. In addition, the response characteristics of the in-wheel system and the electric booster brake were compared through a frequency response analysis. In the cooperative control, the road friction coefficient was estimated using the wheel speed, motor torque, and braking torque of each wheel, and the torque limit of the wheel to the road was determined using the estimated road friction coefficient. Based on the estimated road friction coefficient and torque limit, a cooperative algorithm to control the motor and the electric booster brake was proposed to improve the stability of the in-wheel electric vehicle. The performance of the proposed cooperative control algorithm was evaluated through a hardware-in-the-loop simulation (HILS). Furthermore, to verify the performance of the proposed cooperative control algorithm, a test environment was constructed for the anti-lock braking system (ABS) hydraulic module hardware, and the performance of the cooperative control algorithm was compared with that of the ABS by means of a HILS test.     

A practical identifier design of road variations for anti-lock brake system

Emergency brake technologies have always been a major interest of vehicle active safety-related studies. On homogeneous surfaces, traditional anti-lock brake system (ABS) can achieve efficient braking performance and maintain the handling capability as well. However, when road conditions are time variant during the braking process, or different at the bilateral wheels, braking stability performance is likely to be degraded. To address this problem and enhance ABS performances, a practical identifier of road variations is developed in this study. The proposed identifier adopts a statechart-based approach and is hierarchically constructed with a wheel layer and a full vehicle layer identifier. Based on the identification results, modifications are made to a four-phase wheel-behaviour-based ABS controller to enhance its performance. The feasibility and effectiveness of the proposed identifier in collaborating with the modified ABS controller are examined via simulations and further validated by track tests under various practical braking scenarios.     

Wheel slip control with torque blending using linear and nonlinear model predictive control

Modern hybrid electric vehicles employ electric braking to recuperate energy during deceleration. However, currently anti-lock braking system (ABS) functionality is delivered solely by friction brakes. Hence regenerative braking is typically deactivated at a low deceleration threshold in case high slip develops at the wheels and ABS activation is required. If blending of friction and electric braking can be achieved during ABS events, there would be no need to impose conservative thresholds for deactivation of regenerative braking and the recuperation capacity of the vehicle would increase significantly. In addition, electric actuators are typically significantly faster responding and would deliver better control of wheel slip than friction brakes. In this work we present a control strategy for ABS on a fully electric vehicle with each wheel independently driven by an electric machine and friction brake independently applied at each wheel. In particular we develop linear and nonlinear model predictive control strategies for optimal performance and enforcement of critical control and state constraints. The capability for real-time implementation of these controllers is assessed and their performance is validated in high fidelity simulation.     

Dynamic analysis and control of an anti-lock brake system for a motorcycle with a camber angle

This paper analyses the dynamic response of a motorcycle with an anti-lock brake system (ABS) and camber or steering angle. Most studies have assumed that motorcycles brake in a straight line – that is, without a steering or camber angle. In this work, the performance of an ABS modulator is designed and analysed at first. Then, a controller is designed for motorcycle turning. The controller uses angular acceleration and the pressure value in brake calipers on the front and rear wheels, camber angle and lateral acceleration as commands to control brake pressure on each wheel to prevent wheel locking. The equation of motion for a motorcycle is based on Weir's equations. This motorcycle model combines a mathematical equation of the ABS modulator, tyre model and controller in simulations.     

Optimisation of active suspension control inputs for improved performance of active safety systems

A collocation-type control variable optimisation method is used to investigate the extent to which the fully active suspension (FAS) can be applied to improve the vehicle electronic stability control (ESC) performance and reduce the braking distance. First, the optimisation approach is applied to the scenario of vehicle stabilisation during the sine-with-dwell manoeuvre. The results are used to provide insights into different FAS control mechanisms for vehicle performance improvements related to responsiveness and yaw rate error reduction indices. The FAS control performance is compared to performances of the standard ESC system, optimal active brake system and combined FAS and ESC configuration. Second, the optimisation approach is employed to the task of FAS-based braking distance reduction for straight-line vehicle motion. Here, the scenarios of uniform and longitudinally or laterally non-uniform tyre–road friction coefficient are considered. The influences of limited anti-lock braking system (ABS) actuator bandwidth and limit-cycle ABS behaviour are also analysed. The optimisation results indicate that the FAS can provide competitive stabilisation performance and improved agility when compared to the ESC system, and that it can reduce the braking distance by up to 5% for distinctively non-uniform friction conditions.     

A vehicle ABS adaptive sliding-mode control algorithm based on the vehicle velocity estimation and tyre/road friction coefficient estimations

A sliding-mode observer is designed to estimate the vehicle velocity with the measured vehicle acceleration, the wheel speeds and the braking torques. Based on the Burckhardt tyre model, the extended Kalman filter is designed to estimate the parameters of the Burckhardt model with the estimated vehicle velocity, the measured wheel speeds and the vehicle acceleration. According to the estimated parameters of the Burckhardt tyre model, the tyre/road friction coefficients and the optimal slip ratios are calculated. A vehicle adaptive sliding-mode control (SMC) algorithm is presented with the estimated vehicle velocity, the tyre/road friction coefficients and the optimal slip ratios. And the adjustment method of the sliding-mode gain factors is discussed. Based on the adaptive SMC algorithm, a vehicle's antilock braking system (ABS) control system model is built with the Simulink Toolbox. Under the single-road condition as well as the different road conditions, the performance of the vehicle ABS system is simulated with the vehicle velocity observer, the tyre/road friction coefficient estimator and the adaptive SMC algorithm. The results indicate that the estimated errors of the vehicle velocity and the tyre/road friction coefficients are acceptable and the vehicle ABS adaptive SMC algorithm is effective. So the proposed adaptive SMC algorithm can be used to control the vehicle ABS without the information of the vehicle velocity and the road conditions.     

Transient switching control strategy from regenerative braking to anti-lock braking with a semi-brake-by-wire system

Regenerative braking is an important technology in improving fuel economy of an electric vehicle (EV). However, additional motor braking will change the dynamic characteristics of the vehicle, leading to braking instability, especially when the anti-lock braking system (ABS) is triggered. In this paper, a novel semi-brake-by-wire system, without the use of a pedal simulator and fail-safe device, is proposed. In order to compensate for the hysteretic characteristics of the designed brake system while ensure braking reliability and fuel economy when the ABS is triggered, a novel switching compensation control strategy using sliding mode control is brought forward. The proposed strategy converts the complex coupling braking process into independent control of hydraulic braking and regenerative braking, through which a balance between braking performance, braking reliability, braking safety and fuel economy is achieved. Simulation results show that the proposed strategy is effective and adaptable in different road conditions while the large wheel slip rate is triggered during a regenerative braking course. The research provides a new possibility of low-cost equipment and better control performance for the regenerative braking in the EV and the hybrid EV.     

Longitudinal wheel slip during ABS braking

Anti-lock braking system (ABS) braking tests with two subcompact passenger cars were performed on dry and wet asphalt, as well as on snow and ice surfaces. The operating conditions of the tyres in terms of wheel slip were evaluated using histograms of the wheel slip data. The results showed different average slip levels for different road surfaces. It was also found that changes in the tyre tread stiffness affected the slip operating range through a modification of the slip value at which the maximum longitudinal force is achieved. Variation of the tyre footprint length through modifications in the inflation pressure affected the slip operating range as well. Differences in the slip distribution between vehicles with different brake controllers were also observed. The changes in slip operating range in turn modified the relative local sliding speeds between the tyre and the road. The results highlight the importance of the ABS controller's ability to adapt to changing slip–force characteristics of tyres and provide estimates of the magnitude of the effects of different tyre and road operating conditions.     

基于模糊控制方法的防抱控制系统的研究

本文采用模糊控制方法对车辆防抱制动系统进行了模拟研究，采用单轮的车辆模拟模型，用两种方法研究了防抱系统，即基于车轮滑移率的连续控制系统和基于车轮加减速度及参考滑移率的非连续控制系统。     

具有ABS的汽车制动性能实验模拟系统

介绍了一种在室内模拟汽车道路制动试验的测试系统,该系统不仅可作为汽车防抱死制动系统(ABS)实验教学的设备,亦可作为开发ABS的前期试验装置。     

Application of the Pacejka Magic Formula Tyre Model on a Study of a Hydraulic Anti-Lock Braking System for a Light Motorcycle

The object of the study is to apply the Pacejka magic formula tyre model on a study of a hydraulic anti-lock braking system, especially applied to a light motorcycle. A sliding mode PWM controller is designed and tested. Both simulation and experimental studies of an anti-lock braking system are undertaken. The paper presents an analytical approach for estimating the longitudinal adhesive coefficient between a tyre and the road through the magic formula tyre model, the parameters of which are identified by a genetic algorithm. A dynamic analysis of a light motorcycle is carried out in detail. The experimental results show that the antilock braking system designed in the study is effective to prevent wheels locking during emergency braking. The proposed simulation results match experimental data well.     

Application of the Pacejka Magic Formula Tyre Model on a Study of a Hydraulic Anti-Lock Braking System for a Light Motorcycle

The object of the study is to apply the Pacejka magic formula tyre model on a study of a hydraulic anti-lock braking system, especially applied to a light motorcycle. A sliding mode PWM controller is designed and tested. Both simulation and experimental studies of an anti-lock braking system are undertaken. The paper presents an analytical approach for estimating the longitudinal adhesive coefficient between a tyre and the road through the magic formula tyre model, the parameters of which are identified by a genetic algorithm. A dynamic analysis of a light motorcycle is carried out in detail. The experimental results show that the antilock braking system designed in the study is effective to prevent wheels locking during emergency braking. The proposed simulation results match experimental data well.     

基于MATLAB的汽车ABS安全仿真研究

文章利用MATLAB软件对汽车制动防抱死系统进行安全仿真研究,选取合适的分析对象,把ABS系统拆成整车模型、轮胎模型以及制动器模型,分别对各模型进行受力以及运动分析,建立数学模型。最终在Simulink环境中建立仿真模型,结合整车数据,验证分析了汽车有无ABS系统时的制动效果。结果显示,装有ABS制动防抱死的汽车制动效果更好。     

基于ADAMS与Matlab的ABS模糊控制仿真研究

将多体系统动力学与智能控制理论相结合对汽车制动防抱死控制系统进行了研究，利用ADAMS／CAR建立了汽车整车的多体力学模型，模型包含了前后悬架、动力总成、转向系统、稳定杆、制动系、轮胎力学模型以及车身，同时也考虑了轮胎、衬套、弹簧、减震器等部件的非线性，准确地表达了车辆的动态特性；利用Matlab／Simulink模糊控制工具箱建立了制动防抱死控制系统的模糊控制策略，利用ADAMS／Control接口进行模型的集成、协同仿真，并将仿真结果与另一种控制策略一逻辑门限值控制的仿真结果进行了比较和分析，仿真反映出模糊控制在整车制动防抱死控制系统上的应用效果，结果表明该控制算法稳定好并具有较强的鲁棒性。     

基于Matlab的ABS不同控制方式的仿真

汽车防抱制动系统（ABS）能实时控制车辆产生最佳的制动力矩,避免产生过大的车轮滑移,从而保持汽车的操纵性和稳定性。文中分别采用PID控制、逻辑开关控制两种方法对单轮汽车模型进行了模拟仿真。然后与没有ABS的情况进行对比,通过对仿真图形曲线的分析,得出ABS的防抱死效果明显。     

汽车防抱死制动系统的自抗扰控制研究

汽车防抱死制动系统(Anti-lock Braking System,ABS)的作用是确保汽车制动时行驶方向的稳定性、可靠性,但是目前仍存在非线性、时变性以及参数不确定性等问题.为保证汽车制动行驶过程中的操纵稳定性和安全性,进一步实现各工况下防抱死制动系统的优化控制,以影响整车稳定的变量滑移率为研究对象,分析所设计策略...     

Distributed and self-adaptive vehicle speed estimation in the composite braking case for four-wheel drive hybrid electric car

Considering the controllability and observability of the braking torques of the hub motor, Integrated Starter Generator (ISG), and hydraulic brake for four-wheel drive (4WD) hybrid electric cars, a distributed and self-adaptive vehicle speed estimation algorithm for different braking situations has been proposed by fully utilising the Electronic Stability Program (ESP) sensor signals and multiple powersource signals. Firstly, the simulation platform of a 4WD hybrid electric car was established, which integrates an electronic-hydraulic composited braking system model and its control strategy, a nonlinear seven degrees-of-freedom vehicle dynamics model, and the Burckhardt tyre model. Secondly, combining the braking torque signals with the ESP signals, self-adaptive unscented Kalman sub-filter and main-filter adaptable to the observation noise were, respectively, designed. Thirdly, the fusion rules for the sub-filters and master filter were proposed herein, and the estimation results were compared with the simulated value of a real vehicle speed. Finally, based on the hardware in-the-loop platform and by picking up the regenerative motor torque signals and wheel cylinder pressure signals, the proposed speed estimation algorithm was tested under the case of moderate braking on the highly adhesive road, and the case of Antilock Braking System (ABS) action on the slippery road, as well as the case of ABS action on the icy road. Test results show that the presented vehicle speed estimation algorithm has not only a high precision but also a strong adaptability in the composite braking case.