Dynamics of Pneumatic Tire Vehicles with Connected Suspension Systems

SUMMARY

A vehicle model, with 10 degrees of freedom is used to investigate the skidding conditions of any wheel of the vehicle in motion. Equations for the load transfer and equations for the pneumatic tire spring and shock absorber are derived. Parameters such as gradual cornering, U-curve cornering, the wavy road surface of different wave lengths and cases of independent and connected suspension systems are inputs to the system. The tire calculated forces and their corresponding maximum resistance forces are the outputs of the systems. A connected suspension system is found to resist skidding better than the independent suspension system. The system is non-linear, and numerical solutions are obtained.     

Optimization for Vehicle Suspension I: Time Domain

SUMMARY

A numerical procedure for finding the optimum values of a number of parameters describing a model vehicle suspension has been studied. The vehicle has been modelled by dynamic systems of linear springs and dampers, and the goal is to obtain lower acceleration peaks at an elected design point in the vehicle.

The problem is stated as a mathematical programming problem which can be solved by means of the sequential linear programming technique. The procedure has been implemented for a four wheel independent suspension model capable of being subjected to road irregularities and to centrifugal and braking accelerations.     

Wheel Vibrations and Transient Tire Forces

SUMMARY

This paper presents a survey of the state-of-the-art in predicting the wheel vibrations in a complex dynamic vehicle suspension system and their influence on the forces transduced in a high frequency area from the tire to the vehicle's body. Secondly it presents also the transient evolution of tire models used for prediction and understanding high frequency movements in the tire's contact area, producing the guiding forces and torques during vehicle handling.     

Energy Dissipation Due to Vehicle/Track Interaction

SUMMARY

The effects of track irregularities and wheel profile on the amount of energy dissipated in railroad freight vehicles is examined. A nonlinear computational model is used to determine the average dissipation in the vehicle suspension and the wheel/rail contact patches. This dissipation is a component of the total resistance force acting on the vehicle. Parametric results are presented showing the effects of track geometry, wheel profile, suspension design, and hunting on train resistance. Track geometry studies consider the effects of track quality and curving. The AAR 1:20 wheel profile and the Heumann wheel profile are compared under various operating conditions. Compared with the Heumann profile, the AAR 1:20 profile is shown to have lower average resistance on good quality tangent track, but higher average resistance in steady curves. A trade-off exists between the two profiles when dynamic curve entry is considered.     

Analysis of Influence of Design Parameters on Steered Wheels Shimmy of Heavy Vehicles

SUMMARY

In choosing the steering system parameters the tendency is towards the minimization of kinematic errors that appear during turning. For that developed procedures exist that take into account also the influence of kinematic of the suspension system on kinematic parameters of vehicle turning. Besides that, maintenance tests have shown, that increased deflections of the suspension system lead to increased wear of tires of steered wheels. In this paper, a method is developed for minimization of steered wheel shimmy and its wear also during the straight-line drive of heavy vehicles. The procedure can also be used in the phase of designing the heavy vehicles.     

Theoretical Analysis of a Semi Active Suspension Fitted to an Off-Road Vehicle

A theoretical analysis is presented to model a hydromechanical, semi-active suspension system, first as a single wheel station and then as fitted to each wheel of an off-road vehicle. Predicted results show that two benefits are obtained by comparison with the equivalent passive system. First, vehicle attitude is controlled for changes in body forces arising from static loads or braking/cornering inputs. Second, a significant improvement in ride comfort is obtained because low suspension stiffnesses can be used.     

Adaptive Control of Vehicle Suspension

SUMMARY

An adaptive control scheme for a two-degree-of-freedom vehicle model with active suspension is proposed. The performance goal is to minimize the variance of vehicle body acceleration under inequality constraints imposed on the variance of either tire or suspension deflection. An active suspension is adapted to the changes in vehicle velocity and the type of road (or terrain) surface which is assumed to be reconstructable from the accelerometer measurements. The control gain factors are obtained by the iterative method taking advantage of stochastic linear control theory. The performance of the system is evaluated and compared to that of an active system with constant gain factors and a passive system with adjustable parameters.     

Road roughness estimation based on discrete Kalman filter with unknown input

ABSTRACT

The road roughness acts as a disturbance input to the vehicle dynamics, and causes undesirable vibrations associated with the ride and handing characteristics. Furthermore, the accurate measurement of road roughness plays a key role in better understanding a vehicle dynamic behaviour and active suspension control systems. However, the direct measurement by laser profilometer or other distance sensors are not trivial due to technical and economic issues. This study proposes a new road roughness estimation method by using the discrete Kalman filter with unknown input (DKF-UI). This algorithm is built on a quarter-car model and uses the measurements of the wheel stroke (suspension deflection), and the acceleration of the sprung mass and unsprung mass. The estimation results are compared to the measurements by laser profilometer in-vehicle test.     

Preview suspension control for a full tracked vehicle

In this study, preview control algorithms for the active and semi-active suspension systems of a full tracked vehicle (FTV) are designed based on a 3-D.O.F model and evaluated. The main issue of this study is to make the ride comfort characteristics of a fast moving tracked vehicle better to keep an operator’s driving capability. Since road wheels almost trace the profiles of the road surface as long as the track doesn’t depart from the ground, the preview information can be obtained by measuring only the absolute position or velocity of the first road wheel. Simulation results show that the performance of the sky-hook suspension system almost follows that of full state feedback suspension system and the on-off semi-active system carries out remarkable performance with the combination of 12 on-off semi-active suspension units. The results simulated with 1^st and 2^nd weighting sets mean that the suspension system combined with the soft type of inner suspension and hard type of outer suspension can carry out better ride comfort characteristics than that with identical suspensions. The full tracked vehicle (FTV) system is uncontrollable and the system is split into controllable and uncontrollable subspace using singular value decomposition transformation. Frequency response curves to four types of inputs, such as heaving, pitching, rolling, and warping inputs, also demonstrate the merits of preview control in ride comfort. All the frequency characteristic responses confirm the continuous time results.     

A Full-Car Roll Model of a Vehicle with Controlled Suspension

SUMMARY

The full-car roll model of a vehicle suspension with static and dynamic control (using wheel, body and seat) is described by means of vertical and lateral input for both static and dynamic states. It is shown that the control deteriorates the static performance of the vertical response and improves the performance of the lateral response.     

Investigation on Stability and Possible Chaotic Motions in the Controlled Wheel Suspension System

SUMMARY

The suspension system has to fulfil a large number of partly contradictory requirements which can be improved by the application of controllable elements in the wheel suspension system. A number of studies dealing with the improvement of suspension characteristics have been published. In the present paper the stability of the controlled suspension systems will be examined. In the paper the stability problems of the active suspension system is analysed and the stable parameter regions are determined.     

Braking Force Distribution Control for Improved Vehicle Dynamics and Brake Performance

SUMMARY

This paper describes the feasibility of improving the braking performance of a commercial vehicle by using an electronic braking system. An electronic braking system enables the braking force at each wheel to be independently controlled. Braking force distribution control makes the braking force at each wheel proportional to each wheel's load. Results of computer simulation and vehicle test showed that the proposed control laws can eliminate the effects of a laden condition on the braking distance and can increase the degree of deceleration at which wheel lock occurs, resulting in improved vehicle attitude stability during a critical maneuver.     

A book review of “Dynamik der Kraftfahrzeuge (German)”, Dynamics of Motor Vehicles by M. Mitschke,Springer-Verlag, 1972, 529 pp., 382 figs.

SUMMARY

The demands upon the dynamic behaviour of a vehicle can be stated as an optimization problem. The optimum solution is calculated using an iterative optimization algorithm. Scaling the problem by non-linear transformations reduces the number of iterations. Lagrange multipliers provide useful information about the sensitivity of the optimum with respect to changes of the constraints. The analysis of the dynamic behaviour is performed in the frequency domain. New structural variants are calculated using system synthesis. As an example, the engine, cab and wheel suspension systems of a tractor/semi-trailer have been optimized all together.     

An Advanced Steering System with Active Kinesthetic Feedback for Handling Qualities Improvement

SUMMARY

Advanced Steering System with artificial steering wheel torque-active kinesthetic information feedback for improving handling qualities is discussed. Fundamentally the structure of the system may be considered to another form of model following control. In this system, a driver always remains in the control loop and receives steering control information which give him/her a direct hint to steer a steering wheel. This system works as a stability and control augmentation system of the vehicle to improve the vehicle handling qualities both in compensatory and pursuit control task, and is expected to reduce driver's workload. Effects of this system are analyzed in terms of man-machine system characteristics. Identification of driver dynamics was carried out to find why such improvement could be achieved. Availability of the proposed system is verified by analysis, simulator and proving ground tests.     

Vergleich einiger Rechen- und Messergebnisse zum Fahrverhalten von Sattelzügen

SUMMARY

In this paper some results of theoretical and experimental investigations on the dynamic directional properties of heavy tractor-semitrailer vehicles are presented.

A nonlinear digital computer model was developed on which the theoretical system analysis is based. This model takes account of the nonUnear tire properties and the friction couple of the fifth wheel. A combination of numerical computation methods (Runge-Kutta and Newton-Raphson techniques) is used for the digital computer simulation.

Full scale road tests with articulated vehicles of 38 ton total weight were conducted for experimental validation of the used theoretical model. As input signals to the vehicle, predetermined steering wheel angle functions were used. The system output signals corresponding to these input functions were measured and stored.

A comparison of the obtained theoretical and experimental results shows a very good qualitative agreement and hence leads to the conclusion that the developed theoretical model can give consistent estimates of the basic dynamic vehicle properties.     

Prediction of Wheel/Rail Profile Wear

SUMMARY

The alteration in wheel and rail profiles due to wear involves considerable vehicle and track-maintenance costs, and influences the loading capacity of the rails, as well as the operation safety and riding comfort of the vehicles. In the past twenty years a vehicle dynamics, contact mechanics and tribology based research work has emerged which is also recently continuous in an international scale, and this research is more and more intensive. Parallel to the growing possibilities of computer based analyses, several algorithms and numerical procedures have been elaborated, as well as measurement based experiments have been carried out to establish the reliable prediction of wear-caused wheel and rail profile alterations and to maximise the mileage performance by selecting the optimum vehicle system parameters for running gears operating on a selected railway line or a whole network under specified -in general inherently stochastic - traffic conditions. This paper takes an attempt to introduce the extended sphere of problems of wheel and rail wear prediction, as well as the latest results reflecting the present state of the art.     

Independent Suspension, Self Steered Axle, and 4WS for Busses

The dynamic behavior of commercial vehicles fitted with differentr types of suspension mechanisms and steering devices is investigated in this paper. Six vehicle models have been constructed: 2WS-SA is a standard two wheel steering bus with solid axles; 2WS-DW is a 2WSA vehicle with independent double wishbone suspension in front and rear axles; SSA-SA is a 2WS system with solid axles, the rear one being mounted on a self steered mechanism; SSA-DW is a vehicle with independent double wishbone suspension in the front axle, and a solid self steered rear axle; 4WS-SA has four wheel steering with solid axles; and 4WS-DW is a 4WS vehicle with independent double wishbone suspension in front and rear axles. The dynamic response of these models has been assessed in terms of lateral acceleration, yaw velocity, tire forces, tire force reserves, and slip angles. The expected advantages of a 4WS system (higher acceleration rates and lower slip angles) will be corroborated but, at the same time, it will be shown that they are obtained at the cost of lower force reserves. Self steered mechanisms produce smaller body slip angles, but it will be shown that they give rise to larger yaw velocity overshootings. The particular independent suspension analyzed does not show significant improvements with respect to the solid axle counterpart.     

Literature review and fundamental approaches for vehicle and tire state estimation*

ABSTRACT

Most modern day automotive chassis control systems employ a feedback control structure. Therefore, real-time estimates of the vehicle dynamic states and tire-road contact parameters are invaluable for enhancing the performance of vehicle control systems, such as anti-lock brake system (ABS) and electronic stability program (ESP). Today's production vehicles are equipped with onboard sensors (e.g. a 3-axis accelerometer, 3-axis gyroscope, steering wheel angle sensor, and wheel speed sensors), which when used in conjunction with certain model-based or kinematics-based observers can be used to identify relevant tire and vehicle states for optimal control of comfort, stability and handling. Vehicle state estimation is becoming ever more relevant with the increased sophistication of chassis control systems. This paper presents a comprehensive overview of the state-of-the-art in the field of vehicle and tire state estimation. It is expected to serve as a resource for researchers interested in developing vehicle state estimation algorithms for usage in advanced vehicle control and safety systems.     

Dynamics of Pneumatic Tire Vehicles with Connected Suspension Systems

A vehicle model, with 10 degrees of freedom is used to investigate the skidding conditions of any wheel of the vehicle in motion. Equations for the load transfer and equations for the pneumatic tire spring and shock absorber are derived. Parameters such as gradual cornering, U-curve cornering, the wavy road surface of different wave lengths and cases of independent and connected suspension systems are inputs to the system. The tire calculated forces and their corresponding maximum resistance forces are the outputs of the systems. A connected suspension system is found to resist skidding better than the independent suspension system. The system is non-linear, and numerical solutions are obtained.     

Simulation of the Interaction between Vehicle Wheel and the Unevenness of Road Surface

SUMMARY

A model of the relationship between a vehicle wheel and the unevenness of the road surface is defined. The wheel is considered to be of circular shape. For a given form of unevenness, the excitation functions are evaluated for the individual subsystems of the dynamic vehicle model having 5 degrees of freedom. The vehicle model traverses the uneven surface at a variable velocity. The model provides for the study of the complex dynamic phenomena which occur between the wheel and the unevenness. The response of the model also includes the dynamic stress on the drive when the wheel passes over the unevenness of the road surface.