Improvement of Vehicle Maneuverability by Direct Yaw Moment Control

This paper deals with a study to theoretically formulate an effective method of improving vehicle performance, particularly, its characteristics in the nonlinear region, and to verify the feasibility of the proposed method by calculations and examinations. In order to analyze vehicle characteristics in the nonlinear region, a new method of analysis was developed for determining yaw moment and side force of the vehicle with a parameter of the side slip angle at the center of gravity when its center of gravity point was fixed. The study with this new method found that direct yaw moment control by proper distribution of traction and braking forces on the right and left tires could provide a very effective means of stabilizing vehicle characteristics, specifically for acceleration and deceleration, and enlarging the limit of vehicle maneuverability.     

Integrated Control of Active Rear Wheel Steering and Direct Yaw Moment Control

SUMMARY

An integrated control system of active rear wheel steering (4WS) and direct yaw moment control (DYC) is presented in this paper. Because of the tire nonlinearity that is mainly due to the saturation of cornering forces, vehicle handling performance is improved but limited to a certain extent only by steering control. Direct yaw moment control using braking and/or driving forces is effective not only in linear but also nonlinear ranges of tire friction circle. The proposed control system is a model matching controller which makes the vehicle follow the desired dynamic model by the state feedback of both yaw rate and side slip angle. Various computer simulations are carried out and show that vehicle handling performance is much improved by the integrated control system.     

On the handling performance of a vehicle with different front-to-rear wheel torque distributions

ABSTRACT

The handling characteristic is a classical topic of vehicle dynamics. Usually, vehicle handling is studied by analyzing the understeer coefficient in quasi-steady-state maneuvers. In this paper, experimental tests are performed on an electric vehicle with four independent motors, which is able to reproduce front-wheel-drive, rear-wheel-drive and all-wheel-drive (FWD, RWD and AWD, respectively) architectures. The handling characteristics of each architecture are inferred through classical and new concepts. The study presents a procedure to compute the longitudinal and lateral tire forces, which is based on a first estimate and a subsequent correction of the tire forces that guarantee the equilibrium. A yaw moment analysis is performed to identify the contributions of the longitudinal and lateral forces. The results show a good agreement between the classical and new formulations of the understeer coefficient, and allow to infer a relationship between the understeer coefficient and the yaw moment analysis. The handling characteristics vary with speed and front-to-rear wheel torque distribution. An apparently surprising result arises at low speed: the RWD architecture is the most understeering configuration. This is discussed by analyzing the yaw moment caused by the longitudinal forces of the front tires, which is significant for high values of lateral acceleration and steering angle.     

Optimal Control of Four Wheel Steering Vehicle

SUMMARY

This paper derives a method of controlling four wheel steering using optimal control theory. The purpose of control is to minimize the sideslip angle at the center of gravity. The control method feeds forward the steering wheel angle and feeds back the yaw velocity and the sideslip angle to the front and rear wheel angles. Theoretical studies show that the sideslip angle is reduced to zero even in the transient state, and that the understeer characteristic and frequency response can be changed regardless of the vehicle static margin. This Paper also examines various characteristics of the influence of the side force nonlinearities of tires and crosswinds.     

Optimal control of brakes and steering for autonomous collision avoidance using modified Hamiltonian algorithm

ABSTRACT

This paper considers the problem of collision avoidance for road vehicles, operating at the limits of friction. A two-level modelling and control methodology is proposed, with the upper level using a friction-limited particle model for motion planning, and the lower level using a nonlinear 3DOF model for optimal control allocation. Motion planning adopts a two-phase approach: the first phase is to avoid the obstacle, the second is to recover lane keeping with minimal additional lateral deviation. This methodology differs from the more standard approach of path-planning/path-following, as there is no explicit path reference used; the control reference is a target acceleration vector which simultaneously induces changes in direction and speed. The lower level control distributes vehicle targets to the brake and steer actuators via a new and efficient method, the Modified Hamiltonian Algorithm (MHA). MHA balances CG acceleration targets with yaw moment tracking to preserve lateral stability. A nonlinear 7DOF two-track vehicle model confirms the overall validity of this novel methodology for collision avoidance.     

Integrated Control of Active Rear Wheel Steering and Direct Yaw Moment Control

An integrated control system of active rear wheel steering (4WS) and direct yaw moment control (DYC) is presented in this paper. Because of the tire nonlinearity that is mainly due to the saturation of cornering forces, vehicle handling performance is improved but limited to a certain extent only by steering control. Direct yaw moment control using braking and/or driving forces is effective not only in linear but also nonlinear ranges of tire friction circle. The proposed control system is a model matching controller which makes the vehicle follow the desired dynamic model by the state feedback of both yaw rate and side slip angle. Various computer simulations are carried out and show that vehicle handling performance is much improved by the integrated control system.     

Crosswind Feedforward Control – A Measure to Improve Vehicle Crosswind Behaviour

SUMMARY

The theory of crosswind feedforward control was explained using the example of a vehicle with active front-wheel steering. Beforehand, the calculation formulas and frequency responses of the transient crosswind force and of the wind yaw moment acting on the vehicle were derived using the example of a simple vehicle fluid model. The influence of the transiency of crosswind disturbance on the dynamic crosswind behaviour of a vehicle was then presented. The results of simulation confirmed the analyses carried out in the frequency domain for feedforward control with front, rear and all-wheel steering. With front-wheel steering, the influence of crosswind on one of the vehicle movement variables (lateral acceleration or yaw rate) could be almost completely compensated by dynamic feedforward control. With rear-wheel steering, it is only possible to compensate directly for the influence on the yawing rate. Due to the setting of the side force in the same direction as the lateral wind force at the start, active rear-wheel steering is not so successful as active front-wheel steering. Nevertheless, the crosswind behaviour of a vehicle can be considerably enhanced by feedforward control with rear-wheel steering. The best crosswind behaviour was obtained with active all-wheel steering: the vehicle hardly responds at all to crosswinds and remains on course despite heavy gusts of wind.     

Fault-tolerant yaw moment control with steer — and brake-by-wire devices

This paper presents an fault-tolerant yaw moment control for a vehicle with steer-by-wire (SBW) and brake-by-wire (BBW) devices. SBWs and BBWs can give active front steering (AFS) and electronic stability control (ESC) functions, respectively. Due to motor-driven devices, actuator and sensor faults are inherent in SBW and BBW, and can cause a critical damage to a vehicle. Simple direct yaw moment control is adopted to design a vehicle stability controller. To cope with actuator failure, weighted pseudo-inverse based control allocation (WPCA) with variable weights is proposed in yaw moment distribution procedure. Simulations on vehicle simulation software, CarSim®, show the proposed method is effective for fail safety.     

Design of an Active Unilateral Brake Control System for Five-Axle Tractor-Semitrailer Based on Sensitivity Analysis

SUMMARY

This paper presents the results of a parametric sensitivity analysis of a five-axle tractor-semitrailer vehicle combination using 3-DOF linear yaw/plane model. The first order logarithmic sensitivity functions are derived with respect to several vehicle design parameters. For stabilization of the vehicle's directional behaviour a fairly new control concept called “Active Unilateral Braking Control (AUBC)” acting on the tractor rear wheel's in order to produce a stabilizing yaw torque is investigated. The AUBC system improves not only the directional stability, but also affects the roll dynamics of the vehicle. The sensitivity of the controlled vehicle system with linear quadratic controller (LQR) is also examined, a robust controller design procedure is proposed as a result of the sensitivity analysis. The robustness of this controller in the presence of both internal (including parametric uncertainties, non-linear dynamics) and external disturbances (such as road irregularities and side wind) allows its implementation with confidence with a non-linear vehicle model. The applicability of this control system to a non-linear vehicle model is tested using a 34 DOF, non-linear vehicle model of the tractor-semitrailer combination.     

Integrated fuzzy/optimal vehicle dynamic control

There are basically two methods to control yaw moment which is the most efficient way to improve vehicle stability and handling. The first method is indirect yaw moment control, which works based on control of the lateral tire force through steering angle control. It is mainly known as active steering control (ASC). Nowadays, the most practical approach to steering control is active front steering (AFS). The other method is direct yaw moment control (DYC), in which an unequal distribution of longitudinal tire forces (mainly braking forces) produces a compensating external yaw moment. It is well known that the AFS performance is limited in the non-linear vehicle handling region. On the other hand, in spite of a good performance of DYC in both the linear and non-linear vehicle handling regions, continued DYC activation could lead to uncomfortable driving conditions and an increase in the stopping distance in the case of emergency braking. It is recommended that DYC be used only in high-g critical maneuvers. In this paper, an integrated fuzzy/optimal AFS/DYC controller has been designed. The control system includes five individual optimal LQR control strategies; each one, has been designed for a specific driving condition. The strategies can cover low, medium, and high lateral acceleration maneuvers on high-μ or low-μ roads. A fuzzy blending logic also has been utilized to mange each LQR control strategy contribution level in the final control action. The simulation results show the advantages of the proposed control system over the individual AFS or DYC controllers.     

Design and evaluation of sideslip angle observer for vehicle stability control

This paper presents a method for estimating the vehicle side slip angle, which is considered as a significant signal in determining the vehicle stability region in vehicle stability control systems. The proposed method combines the model-based method and kinematics-based method. Side forces of the front and rear axles are provided as a weighted sum of directly calculated values from a lateral acceleration sensor and a yaw rate sensor and from a tire model according to the nonlinear factor, which is defined to identify the degree of nonlinearity of the vehicle state. Then, the side forces are fed to the extended Kalman filter, which is designed based on the single-track vehicle model associated with a tire model. The cornering stiffness identifier is introduced to compensate for tire force nonlinearities. A fuzzy-logic procedure is implemented to determine the nonlinear factor from the input variables: yaw rate deviation from the reference value and lateral acceleration. The proposed observer is compared with a model-based method and kinematics-based method. An 8 DOF vehicle model and Dugoff tire model are employed to simulate the vehicle state in MATLAB/SIMULINK. The simulation results shows that the proposed method is more accurate than the model-based method and kinematics-based method when the vehicle is subjected to severe maneuvers under different road conditions.     

Nonlinear PI front and rear steering control in four wheel steering vehicles

Vehicle steering dynamics show resonances, which depend on the longitudinal speed, unstable equilibrium points and limited stability regions depending on the constant steering wheel angle, longitudinal speed and car parameters.

The main contribution of this paper is to show that a combined decentralized proportional active front steering control and proportional-integral active rear steering control from the yaw rate tracking error can assign the eigenvalues of the linearised single track steering dynamics, without lateral speed measurements, using a standard single track car model with nonlinear tire characteristics and a non-linear first-order reference model for the yaw rate dynamics driven by the driver steering wheel input. By choosing a suitable nonlinear reference model it is shown that the responses to driver step inputs tend to zero (or reduced) lateral speed for any value of longitudinal speed: in this case the resulting controlled vehicle static gain from driver input to yaw rate differs from the uncontrolled one at higher speed. The closed loop system shows the advantages of both active front and rear steering control: higher controllability, enlarged bandwidth for the yaw rate dynamics, suppressed resonances, new stable cornering manoeuvres, enlarged stability regions, reduced lateral speed and improved manoeuvrability; in addition comfort is improved since the phase lag between lateral acceleration and yaw rate is reduced.

For the designed control law a robustness analysis is presented with respect to system failures, driver step inputs and critical car parameters such as mass, moment of inertia and front and rear cornering stiffness coefficients. Several simulations are carried out on a higher order experimentally validated nonlinear dynamical model to confirm the analysis and to explore the robustness with respect to unmodelled dynamics.     

A novel direct yaw moment controller for in-wheel motor electric vehicles

A novel direct yaw moment controller is developed in this paper. A hierarchical control architecture is adopted in the controller design. In the upper controller, a driver model and a vehicle model are used to obtain the driver's intention and the vehicle states, respectively. The upper controller determines the desired yaw moment by means of sliding mode control. The lower controller distributes differential longitudinal forces according to the desired yaw moment. A nonlinear tyre model, ‘UniTire’, is utilised to develop the novel distribution strategy and the control boundary.     

智能汽车轨迹跟踪与横摆稳定性协同控制

为了提高四轮独立驱动智能电动汽车在变曲率弯道下的轨迹跟踪精度和横摆稳定性,提出了一种模型预测控制与直接横摆力矩控制协同的综合控制方法。建立了横纵向耦合的车辆动力学模型,采用2阶龙格库塔离散法保证了离散模型的精度,并基于简化的2自由度动力学模型推导了车辆横摆稳定性约束,设计了非线性模型预测控制器;利用直接横摆力矩控制能够改变车辆横摆角速度和航向角的特点,考虑模型预测控制器的预测状态、控制量以及跟踪误差,设计了协同控制规则。仿真结果表明,协同控制方法解决了考虑横摆稳定性约束的模型预测控制器中存在的稳定性约束与控制精度相矛盾的问题,并补偿了模型预测控制器没有可行解时对横摆稳定性的约束,同时提高了智能汽车的轨迹跟踪精度和横摆稳定性。     

Effects of model response on model following type of combined lateral force and yaw moment control performance for active vehicle handling safety

This paper presents a comparison study of the effect of model response on the performance of the model following type combined lateral force and yaw moment control. The combined controls aim to maximize stability limit as well as vehicle responsiveness. In order to realize this aim, two types of model responses are proposed to introduce the required lateral force and yaw moment control. The model responses (a) is the side-slip angle and yaw rate vehicle response of the two degree of freedom vehicle motion (bicycle model). The model responses (b) is an intentional modification from the model responses (a) to the side slip angle converging to zero and first order yaw rate. Three different cases of combining lateral force and yaw moment control have been investigated using the two types of model responses. The effect of model responses is proved by computer simulations of the vehicle response to a single sine wave steering input with braking for the combined control methods proposed. It is found that the influence of the model response has a significant effect on the combined control performance.     

Coordinated control strategies for active steering,differential braking and active suspension for vehicle stability,handling and safety improvement

ABSTRACT

In this paper, a coordinated control strategy is proposed to provide an effective improvement in handling stability of the vehicle, safety, and comfortable ride for passengers. This control strategy is based on the coordination among active steering, differential braking, and active suspension systems. Two families of controllers are used for this purpose, which are the high order sliding mode and the backstepping controllers. The control strategy was tested on a full nonlinear vehicle model in the environment of MATLAB/Simulink. Rollover avoidance and yaw stability control constraints have been considered. The control system mainly focuses on yaw stability control. When rollover risk is detected, the proposed strategy controls the roll dynamics to decrease rollover propensity. Simulation results for two different critical driving scenarios, the first one is a double lane change and the other one is a J-turn manoeuvre, show the effectiveness of the coordination strategy in stabilising the vehicle, enhancing handling and reducing rollover propensity.     

Vehicle control synthesis using phase portraits of planar dynamics

ABSTRACT

Phase portraits provide control system designers strong graphical insight into nonlinear system dynamics. These plots readily display vehicle stability properties and map equilibrium point locations and movement to changing parameters and system inputs. This paper extends the usage of phase portraits in vehicle dynamics to control synthesis by illustrating the relationship between the boundaries of stable vehicle operation and the state derivative isoclines in the yaw rate–sideslip phase plane. Closed-loop phase portraits demonstrate the potential for augmenting a vehicle's open-loop dynamics through steering and braking. The paper concludes by applying phase portrait analysis to an envelope control algorithm for yaw stability and a sliding surface controller for stabilising a saddle point equilibrium in drifting.     

Lateral handling improvement with dynamic curvature control for an independent rear wheel drive EV

The integrated longitudinal and lateral dynamic motion control is important for four wheel independent drive (4WID) electric vehicles. Under critical driving conditions, direct yaw moment control (DYC) has been proved as effective for vehicle handling stability and maneuverability by implementing optimized torque distribution of each wheel, especially with independent wheel drive electric vehicles. The intended vehicle path upon driver steering input is heavily depending on the instantaneous vehicle speed, body side slip and yaw rate of a vehicle, which can directly affect the steering effort of driver. In this paper, we propose a dynamic curvature controller (DCC) by applying a the dynamic curvature of the path, derived from vehicle dynamic state variables; yaw rate, side slip angle, and speed of a vehicle. The proposed controller, combined with DYC and wheel longitudinal slip control, is to utilize the dynamic curvature as a target control parameter for a feedback, avoiding estimating the vehicle side-slip angle. The effectiveness of the proposed controller, in view of stability and improved handling, has been validated with numerical simulations and a series of experiments during cornering engaging a disturbance torque driven by two rear independent in-wheel motors of a 4WD micro electric vehicle.     

On the objective assessment and quantification of the transient-handling response of a vehicle

This article suggests a new methodology for the objective assessment and quantification of the response of a vehicle subjected to transient-handling manoeuvres. For this purpose, a non-dimensional measure is defined, namely the normalized yaw impulse. This measure appears in two variations. In its general or dynamic form, it represents the difference between the yaw moment due to the front-tyre forces and the yaw moment due to the rear-tyre forces, divided by the sum of the aforementioned yaw moments. By employing a linear, two-degree-of-freedom bicycle model, it is shown that the general form of the normalized yaw impulse can be written as a function of the steer angle and the forward, lateral and yaw velocities of the vehicle. This form is referred to as the kinematic yaw impulse. It is demonstrated that the combined application of the dynamic and kinematic expressions of the yaw impulse not only facilitates the explicit assessment and quantification of the transient behaviour of a vehicle, but also reveals the influence of parameters such as the yaw moment of inertia, which traditionally leave the steady-state behaviour unaffected.     

基于横摆力矩的汽车稳定性控制策略

为提高车辆的横向稳定性,获得良好的操纵性能,利用ADAMS/car和MATLAB/simulink建立了以横摆角速度和质心侧偏角为控制变量的多级PID仿真模型,分别采用了单个车轮制动和单侧车轮制动产生附加横摆力矩的方式.通过蛇形试验验证了ESP控制器的有效性和对比了2种制动方式的控制效果.仿真试验表明：采用该ESP控制器可以很好地保持车辆的稳定性,采用单侧车轮制动产生附加横摆力矩的方式具有更快的控制速度和更好的控制效果.