Development and implementation of a torque vectoring algorithm for an innovative 4WD driveline for a high-performance vehicle

The sporting spirit that characterises a high-performance car can be observed in certain technical solutions. The power distribution on the rear wheels is the simplest example of that. It is well known that rear-wheel drive (RWD) vehicles are more fun to drive and faster in their reactions. Unfortunately, they are also less intuitive and harder to control because of their natural oversteering behaviour. The idea of maintaining an RWD driveline in the future is not farseeing, because it would imply an excessive tyre dimension increasing to let the driver use all engine power in many cornering and low-friction conditions. The choice of adopting a part-time all-wheel drive (AWD) driveline comes from the will of enhancing the overall performance by using all the available friction every time that it is needed. It has to be kept into account that a normally aspirated motor of a sport car can supply 500–600 Hp nowadays, and that it will supply 700–800 Hp in the very near future. However, the proposed driveline has not to worsen the weight characteristics (mass and load distribution) that make an RWD vehicle better than other cars. Because of all these considerations and constraints, a new driveline system has been designed. It derives from an RWD driveline with a semi-active differential, to which has been added a controlled wet clutch that directly connects the engine to the front differential. This device allows the drive torque to be distributed between the two axles. It can be understood that in such a device, the torque distribution does not depend only on the central clutch action, but also on the engaged gear. Because of this particular layout, this system can not work in the whole gear range because of thermal problems due to kinematical reasons. So the centre clutch controller has to consider the gear position too. The control algorithms development was carried out using a vehicle model, which can precisely simulate the handling response, the powertrain dynamic, and the actuation system behaviour. Such a modelling precision required the development of a customised powertrain model library in Matlab/Simulink.     

Additional 4WS and Driver Interaction

SUMMARY

This investigation is based on a complex 4-wheel vehicle model of a passenger car that includes steering system and drive train. The tyre properties are described for all possible combined longitudinal and lateral slip values and for arbitrary friction conditions. The active part is an additional steering system of all 4 wheels, additionally to the driver's steering wheel angle input. Three control levels are used for the driver model that thereby can follow a given trajectory or avoid an obstacle.

The feedback control of the additional 4 wheel steering is based on an observer which can also have adaptive characteristics. Moreover a virtual vehicle model in a feedforward scheme can provide desired steering characteristics.

To get information for critical situations a cornering manoeuvre with sudden u-split conditions is simulated. Further a similar manoeuvre is used to evaluate the reentry in a high friction area from low friction conditions. And finally the performance of the controller is shown in a severe lane change manoeuvre.     

Nonlinear dynamics and stability analysis of vehicle plane motions

In this article, the problems of dynamics and stability for vehicle planar motion systems have been investigated. By introducing a so-called joint-point locus approach, equilibria of the system and their associated stability properties are given geometrically. With this method, it is discovered that the difference between the front and the rear steering angles plays a key role in vehicle system dynamics and that the topological structure of the phase portrait and the types of bifurcations are different from those published previously. In particular, the vehicle system could still be stabilized even when pushed to work in a certain severely nonlinear region, by applying extremely large steering angles. However, it is worth noticing that the attractive domain of the stable equilibrium is very narrow. These developments might prove to be important in active steering control design. Numerical experiments are carried out to illustrate the potentials of the proposed techniques.     

Road and off-road vehicle system dynamics. Understanding the future from the past

A detailed analysis of scientific research directions and methods in ground vehicle dynamics and vehicle system dynamics during the past century is presented in this article. What started as peculiarities of vehicle motion, dynamics of vehicles went through extensive research and engineering work and was established as an applied science – vehicle dynamics. Steady motion and transient manoeuvres, multi-flexible-body dynamics, nonlinear and stochastic dynamics, terramechanics, vehicle operational properties and their multi-criterion optimisation, computer modelling and simulation, analysis and optimal synthesis, various controls, inverse vehicle dynamics, open architecture-type, and multi-domain vehicle systems – these are the milestones of developments over the past century. This article considers the subject-matter and the substance of vehicle dynamics in general, and new research directions of modern vehicle dynamics in particular. It is shown that modern vehicle dynamics is acquiring principally new features including agile dynamics of multi-physics mechatronic systems (including cyber-type systems), coupled and interactive vehicle system dynamics.     

Trends in vehicle motion control for automated driving on public roads

ABSTRACT

In this paper, we describe how vehicle systems and the vehicle motion control are affected by automated driving on public roads. We describe the redundancy needed for a road vehicle to meet certain safety goals. The concept of system safety as well as system solutions to fault tolerant actuation of steering and braking and the associated fault tolerant power supply is described. Notably restriction of the operational domain in case of reduced capability of the driving automation system is discussed. Further we consider path tracking, state estimation of vehicle motion control required for automated driving as well as an example of a minimum risk manoeuver and redundant steering by means of differential braking. The steering by differential braking could offer heterogeneous or dissimilar redundancy that complements the redundancy of described fault tolerant steering systems for driving automation equipped vehicles. Finally, the important topic of verification of driving automation systems is addressed.     

宝马主动转向技术概述

回顾了车辆转向系统的发展历程。指出,相比于线控转向,主动转向技术是今后发展的主要趋势。详细介绍了主动转向系统的结构和组成,以及核心部件双行星齿轮机构的工作原理及工作模式。叙述了该系统变传动比、稳定车辆等功能的实现原理,并指出通过与其他动力学控制系统一起实现底盘一体化集成控制将是主动转向技术未来的发展方向。     

Advanced vehicle dynamics of heavy trucks with the perspective of road safety

ABSTRACT

This paper presents state-of-the art within advanced vehicle dynamics of heavy trucks with the perspective of road safety. The most common accidents with heavy trucks involved are truck against passenger cars. Safety critical situations are for example loss of control (such as rollover and lateral stability) and a majority of these occur during speed when cornering. Other critical situations are avoidance manoeuvre and road edge recovery. The dynamic behaviour of heavy trucks have significant differences compared to passenger cars and as a consequence, successful application of vehicle dynamic functions for enhanced safety of trucks might differ from the functions in passenger cars. Here, the differences between vehicle dynamics of heavy trucks and passenger cars are clarified. Advanced vehicle dynamics solutions with the perspective of road safety of trucks are presented, beginning with the topic vehicle stability, followed by the steering system, the braking system and driver assistance systems that differ in some way from that of passenger cars as well.     

Modeling and control of an anti-lock brake and steering system for cooperative control on split-mu surfaces

The brake and steering systems in vehicles are the most effective actuators that directly affect the vehicle dynamics. In general, the brake system affects the longitudinal dynamics and the steering system affects the lateral dynamics; however, their effects are coupled when the vehicle is braking on a non-homogenous surface, such as a split-mu road. The yaw moment compensation of the steering control on a split-mu road is one of the basic functions of integrated or coordinated chassis control systems and has been demonstrated by several chassis suppliers. However, the disturbance yaw moment is generally compensated for using the yaw rate feedback or using wheel brake pressure measurement. Access to the wheel brake pressure through physical sensors is not cost effective; therefore, we modeled the hydraulic brake system to avoid using physical sensors and to estimate the brake pressure. The steering angle controller was designed to mitigate the non-symmetric braking force effect and to stabilize the yaw rate dynamics of the vehicle. An H-infinity design synthesis was used to take the system model and the estimation errors into account, and the designed controller was evaluated using vehicle tests.     

Comparison of All-Wheel Steerings in the System Driver-Vehicle

SUMMARY

Different load or tires and a drive on an ice-coated road can overcharge a driver to such an extend, that the result may be an accident. Therefore the aim of development is a self-acting compensation of the vehicle to different vehicle transfer behaviour (invariant vehicle behaviour).

The calculation of so called optimal characteristics shows, that only rear-wheel steering cannot realize this aim of development. Therefore an additional front-wheel angle, which is not influenced by the driver, is necessary. A transfer function can be calculated in order to get controlled steering of the rear wheels without the influence of load.

It is not possible to realize optimal characteristics, because the parameters of the vehicle are difficult to measure. Only an optimal diagnosis and control of driving condition realize a relief for the driver in every driving situation in order to avoid most of the accidents.

The often demanded sideslip angle compensation only worsens driving conditions on ice-coated roads. Therefore systems which identify the driving condition themselves have to be favoured in any case.     

An Active Roll-Moment Control Strategy for Narrow Tilting Commuter Vehicles

SUMMARY

An automatic tilt control strategy for a narrow commuter vehicle is described. Such a vehicle would be enclosed like a conventional car but would bank into turns like a motorcycle and so it would feel quite unconventional to drive. The proposed tilt control system uses the steering to tilt the car over like a motorcycle but this is augmented by actively generating a rolling moment about the pivot axis between the tilting upper body and non-tilting base. The provision of this active direct tilt control enables the vehicle to remain upright at low or zero speed and also permits the designer to fine tune the transient roll response. Although it appears complex the proposed tilting control relies on only a few simple sensor measurements, some modest, microprocessor based signal processing and low power, low bandwidth steering and tilt control actuators which might be derived from existing automotive components.     

A Fuzzy Logic Direct Yaw-Moment Control System for All-Wheel-Drive Electric Vehicles

Summary In-wheel-motors are revolutionary new electric drive systems that can be housed in vehicle wheel assemblies. Such E-wheels permit packaging flexibility by eliminating the central drive motor and the associated transmission and driveline components, including the transmission, the differential, the universal joints and the drive shaft. Apart from many advantages of such a system, unequalled independent wheel control allows vehicle dynamic improvement to assist the driver in enhancing cornering and straight-line stability on slippery roads and in adverse ground conditions. In this paper a Fuzzy logic driver-assist stability system for all-wheel-drive electric vehicles based on a yaw reference DYC is introduced. The system assists the driver with path correction, thus enhancing cornering and straight-line stability and providing enhanced safety. A feed-forward neural network is employed to generate the required yaw rate reference. The neural net maps the vehicle speed and the steering angle to give the yaw rate reference. The vehicle true speed is estimated using a multi-sensor data fusion method. Data from wheel sensors and an embedded accelerometer are fed into an estimator, where a Fuzzy logic system decides which input is more reliable. The efficiency of the proposed system is approved by conducting a computer simulation. The proposed control system is an effective and easy to implement method to enhance the stability of all-wheel-drive electric vehicles.     

A Fuzzy Logic Direct Yaw-Moment Control System for All-Wheel-Drive Electric Vehicles

Summary In-wheel-motors are revolutionary new electric drive systems that can be housed in vehicle wheel assemblies. Such E-wheels permit packaging flexibility by eliminating the central drive motor and the associated transmission and driveline components, including the transmission, the differential, the universal joints and the drive shaft. Apart from many advantages of such a system, unequalled independent wheel control allows vehicle dynamic improvement to assist the driver in enhancing cornering and straight-line stability on slippery roads and in adverse ground conditions. In this paper a Fuzzy logic driver-assist stability system for all-wheel-drive electric vehicles based on a yaw reference DYC is introduced. The system assists the driver with path correction, thus enhancing cornering and straight-line stability and providing enhanced safety. A feed-forward neural network is employed to generate the required yaw rate reference. The neural net maps the vehicle speed and the steering angle to give the yaw rate reference. The vehicle true speed is estimated using a multi-sensor data fusion method. Data from wheel sensors and an embedded accelerometer are fed into an estimator, where a Fuzzy logic system decides which input is more reliable. The efficiency of the proposed system is approved by conducting a computer simulation. The proposed control system is an effective and easy to implement method to enhance the stability of all-wheel-drive electric vehicles.     

New approaches to enhance active steering system functionalities: preliminary results

An important development of the steering systems in general is active steering systems like active front steering and steer-by-wire systems. In this paper the current functional possibilities in application of active steering systems are explored. A new approach and additional functionalities are presented that can be implemented to the active steering systems without additional hardware such as new sensors and electronic control units. Commercial active steering systems are controlling the steering angle depending on the driving situation only. This paper introduce methods for enhancing active steering system functionalities depending not only on the driving situation but also vehicle parameters like vehicle mass, tyre and road condition. In this regard, adaptation of the steering ratio as a function of above mentioned vehicle parameters is presented with examples. With some selected vehicle parameter changes, the reduction of the undesired influences on vehicle dynamics of these parameter changes has been demonstrated theoretically with simulations and with real-time driving measurements.     

Modelling and control of a new differential steering concept

This paper presents a new steer-by-wire concept using an all-wheel drive vehicle layout with in-wheel motors while completely omitting the application of any dedicated steering device. Steering is based on the so-called differential steering principle which generates the necessary steering moment about the kingpins by a traction force difference between left and right sides of the vehicle. In order to investigate the behaviour of the vehicle and to design the underlying control algorithms, a planar vehicle model is presented, where the vehicle is described as constrained non-holonomic system requiring a special treatment. A state feedback linear controller for controlling of the lateral dynamics of the vehicle at higher speeds and a simple PI angle controller for low-speed manoeuvring are developed. The resulting behaviour of the system is investigated by various simulation experiments demonstrating a comparable steering performance of the new steering concept as that of conventional passenger cars.     

Nonlinear PI front and rear steering control in four wheel steering vehicles

Vehicle steering dynamics show resonances, which depend on the longitudinal speed, unstable equilibrium points and limited stability regions depending on the constant steering wheel angle, longitudinal speed and car parameters.

The main contribution of this paper is to show that a combined decentralized proportional active front steering control and proportional-integral active rear steering control from the yaw rate tracking error can assign the eigenvalues of the linearised single track steering dynamics, without lateral speed measurements, using a standard single track car model with nonlinear tire characteristics and a non-linear first-order reference model for the yaw rate dynamics driven by the driver steering wheel input. By choosing a suitable nonlinear reference model it is shown that the responses to driver step inputs tend to zero (or reduced) lateral speed for any value of longitudinal speed: in this case the resulting controlled vehicle static gain from driver input to yaw rate differs from the uncontrolled one at higher speed. The closed loop system shows the advantages of both active front and rear steering control: higher controllability, enlarged bandwidth for the yaw rate dynamics, suppressed resonances, new stable cornering manoeuvres, enlarged stability regions, reduced lateral speed and improved manoeuvrability; in addition comfort is improved since the phase lag between lateral acceleration and yaw rate is reduced.

For the designed control law a robustness analysis is presented with respect to system failures, driver step inputs and critical car parameters such as mass, moment of inertia and front and rear cornering stiffness coefficients. Several simulations are carried out on a higher order experimentally validated nonlinear dynamical model to confirm the analysis and to explore the robustness with respect to unmodelled dynamics.     

Analysis of Automatic Steering Control for Highway Vehicles with Look-down Lateral Reference Systems

SUMMARY

In this paper, steering control for passenger cars on automated highways is analyzed, concentrating on look-down reference systems. Extension of earlier experimental results for low speed to highway speed is shown to be non-trivial. The limitations of pure output-feedback of lateral vehicle displacement from the road reference are examined under practical constraints and performance requirements like robustness, maximum lateral error and comfort. The in-depth system analysis directly leads to a new alternative design direction which allows to preserve look-ahead reference systems for highway speed automatic driving.     

Crosswind Feedforward Control – A Measure to Improve Vehicle Crosswind Behaviour

SUMMARY

The theory of crosswind feedforward control was explained using the example of a vehicle with active front-wheel steering. Beforehand, the calculation formulas and frequency responses of the transient crosswind force and of the wind yaw moment acting on the vehicle were derived using the example of a simple vehicle fluid model. The influence of the transiency of crosswind disturbance on the dynamic crosswind behaviour of a vehicle was then presented. The results of simulation confirmed the analyses carried out in the frequency domain for feedforward control with front, rear and all-wheel steering. With front-wheel steering, the influence of crosswind on one of the vehicle movement variables (lateral acceleration or yaw rate) could be almost completely compensated by dynamic feedforward control. With rear-wheel steering, it is only possible to compensate directly for the influence on the yawing rate. Due to the setting of the side force in the same direction as the lateral wind force at the start, active rear-wheel steering is not so successful as active front-wheel steering. Nevertheless, the crosswind behaviour of a vehicle can be considerably enhanced by feedforward control with rear-wheel steering. The best crosswind behaviour was obtained with active all-wheel steering: the vehicle hardly responds at all to crosswinds and remains on course despite heavy gusts of wind.     

某轻型客车转向系统设计校核

转向系统的作用是接受驾驶员的方向操作,带动连杆动作,使轮胎产生转向角来实现行驶车辆的转向.对转向系统的要求是:操纵轻便,安全可靠,有自动回正作用,传到转向盘上逆向力冲击要小.文章详细的阐述了液压转向助力系统的构成及功能,并对某轻型客车转向系统各性能参数进行设计校核,以判定转向系统的零部件参数是否满足法规及使用要求,最终...     

Integrated Control of Active Rear Wheel Steering and Direct Yaw Moment Control

SUMMARY

An integrated control system of active rear wheel steering (4WS) and direct yaw moment control (DYC) is presented in this paper. Because of the tire nonlinearity that is mainly due to the saturation of cornering forces, vehicle handling performance is improved but limited to a certain extent only by steering control. Direct yaw moment control using braking and/or driving forces is effective not only in linear but also nonlinear ranges of tire friction circle. The proposed control system is a model matching controller which makes the vehicle follow the desired dynamic model by the state feedback of both yaw rate and side slip angle. Various computer simulations are carried out and show that vehicle handling performance is much improved by the integrated control system.