Observing freeway ramp merging phenomena in congested traffic

This work conducts a comprehensive investigation of traffic behavior and characteristics during freeway ramp merging under congested traffic conditions. On the Tokyo Metropolitan Expressway, traffic congestion frequently occurs at merging bottleneck sections, especially during heavy traffic demand. The Tokyo Metropolitan Expressway public corporation, generally applies different empirical strategies to increase the flow rate and decrease the accident rate at the merging sections. However, these strategies do not rely either on any behavioral characteristics of the merging traffic or on the geometric design of the merging segments. There have been only a few research publications concerned with traffic behavior and characteristics in these situations. Therefore, a three‐year study is undertaken to investigate traffic behavior and characteristics during the merging process under congested situations. Extensive traffic data capturing a wide range of traffic and geometric information were collected using detectors, videotaping, and surveys at eight interchanges in Tokyo Metropolitan Expressway. Maximum discharged flow rate from the head of the queue at merging sections in conjunction with traffic and geometric characteristics were analyzed. In addition, lane changing maneuver with respect to the freeway and ramp traffic behaviors were examined. It is believed that this study provides a thorough understanding of the freeway ramp merging dynamics. In addition, it forms a comprehensive database for the development and implementation of congestion management techniques at merging sections utilizing Intelligent Transportation System.     

Developing control strategies for freeway merging points under congested traffic situations using modeling and a simulation approach

This work focuses on developing a variety of strategies for alleviating congestion at freeway merging points as well as improving the safety of these points. On the Tokyo Metropolitan Expressway, traffic congestion frequently occurs at merging bottleneck sections, especially during heavy traffic demand. The Tokyo Metropolitan Expressway public corporation, generally applies different empirical strategies to increase the flow rate and decrease the accident rate at the merging sections. However, these strategies do not rely either on any behavioral characteristic of the merging traffic or on the geometric design of the merging segments. There have been only a few research publications concerned with traffic behavior and characteristics in these situations. Therefore, a three‐year extensive study has been undertaken to investigate traffic behavior and characteristics during the merging process under congested situations in order to design safer and less congested merging points as well as to apply more efficient control at these bottleneck sections. Two groups of strategies were investigated in this study. The First group was related to the traffic characteristics, and the second group to the geometric characteristics. In the first group, the control strategies related to closure of freeway and ramp lanes as well as lane‐changing maneuver restriction were investigated through a simulation program, detector data, and field experiment. In the second group, the angle of convergence of the ramp with the freeway in relation to merging capacity was analyzed using a simulation program. Results suggested the potential benefits of using proposed strategies developed in this work and can serve as initial guidance for the reduction of delay and improvement of safety under congested traffic conditions.     

A kinematic wave theory of lane-changing traffic flow

Frequent lane-changes in highway merging, diverging, and weaving areas could disrupt traffic flow and, even worse, lead to accidents. In this paper, we propose a simple model for studying bottleneck effects of lane-changing traffic and aggregate traffic dynamics of a roadway with lane-changing areas. Based on the observation that, when changing its lane, a vehicle affects traffic on both its current and target lanes, we propose to capture such lateral interactions by introducing a new lane-changing intensity variable. With a modified fundamental diagram, we are able to study the impacts of lane-changing traffic on overall traffic flow. In addition, the corresponding traffic dynamics can be described with a simple kinematic wave model. For a location-dependent lane-changing intensity variable, we discuss kinematic wave solutions of the Riemann problem of the new model and introduce a supply–demand method for its numerical solutions. With both theoretical and empirical analysis, we demonstrate that lane-changes could have significant bottleneck effects on overall traffic flow. In the future, we will be interested in studying lane-changing intensities for different road geometries, locations, on-ramp/off-ramp flows, as well as traffic conditions. The new modeling framework could be helpful for developing ramp-metering and other lane management strategies to mitigate the bottleneck effects of lane-changes.     

A merging–giveway interaction model of cars in a merging section: a game theoretic analysis

In many past studies dealing with traffic phenomena in merging or weaving sections, only the influence of through traffic on the behavior of a merging car is considered in the analysis. It is, however, often seen that a through car, which runs on the most outside lane, takes a cooperative motion for the merging car called “giving way” by moving to the adjacent lane. That is, both the merging car and the through car affect one another. Because their influence is not independent from one another, it should be jointly treated in the analysis as “interaction”. This behavior is typical in merging sections, and is a dominant factor forming the traffic phenomena in a section of this type. This study develops a game theoretical model to describe the traffic behavior of a pair of merging and through cars, while explicitly considering the interaction between them. Both the merging and through cars attempt to take the best actions for themselves by forecasting the other’s action, respectively. Such a behavior is modeled as a two-person non-zero-sum non-cooperative game. Through a case study with data analysis of videotaped observation, the proposed model can be used to obtain an understanding of traffic behavior at on-ramp merging sections. ©     

Evaluating the effects of automated vehicle technology on the capacity of freeway weaving sections

Weaving sections, where a merge and a diverge are in close proximity, are considered as crucial bottlenecks in the highway network. Lane changes happen frequently in such sections, leading to a reduced capacity and the traffic phenomenon known as capacity drop. This paper studies how the emerging automated vehicle technology can improve the operations and increase the capacity of weaving sections. We propose an efficient yet effective multiclass hybrid model that considers two aspects of this technology in scenarios with various penetration rates: (i) the potential to control the desired lane change decisions of automated vehicles, which is represented in a macroscopic manner as the distribution of lane change positions, and (ii) the lower reaction time associated with automated vehicles that can reduce headways and the required gaps for lane changing maneuvers. The proposed model is successfully calibrated and validated with empirical observations from conventional vehicles at a weaving section near the city of Basel, Switzerland. It is able to replicate traffic dynamics in weaving sections including the capacity drop. This model is then applied in a simulation-based optimization framework that searches for the optimal distribution of the desired lane change positions to maximize the capacity of weaving sections. Simulation results show that by optimizing the distribution of the desired lane change positions, the capacity of the studied weaving section can increase up to 15%. The results also indicate that if the reaction time is considered as well, there is an additional combined effect that can further increase the capacity. Overall, the results show the great potential of the automated vehicle technology for increasing the capacity of weaving sections.     

Driving behaviour at motorway ramps and weaving segments based on empirical trajectory data

In the vicinity of ramps, drivers make route choices, change lanes and in most cases also adjust their speeds. This can trigger anticipatory behaviour by the surrounding vehicles, which are also reflected in lane changes and/or changes in speed. This phenomenon is called turbulence and is widely recognised by the scientific literature and various design guidelines. However the knowledge about the characteristics of turbulence is limited. This study investigates the microscopic characteristics of driving behaviour around 14 different on-ramps (3), off-ramps (3) and weaving segments (8) in The Netherlands, based on unique empirical trajectory data collected from a video camera mounted underneath a hovering helicopter. The data analysis reveals that lane changes caused by merging and diverging vehicles create most turbulence, that an increase in the amount of traffic results in a higher level of turbulence and that an increase in the available length for merging and diverging results in a lower level of turbulence. The results of this study are useful for improving the road design guidelines and for modelling driving behaviour more realistically.     

Methods of dropping auxiliary lanes at freeway weaving segments

Auxiliary lanes connecting freeway entrance and exit ramps provide additional space for entering and exiting vehicles to change lanes. The method of dropping auxiliary lanes is critical in the design of freeway auxiliary lanes. This study investigates the performance of different methods of dropping auxiliary lanes. Case studies were conducted at two selected freeway segments with successive entrance or exit ramps in the City of Houston. Traffic simulation analysis results of these two case studies show that additional operational benefits can be achieved by extending an auxiliary lane beyond the freeway weaving segment. The study also found that if the weaving segment is followed by an entrance/exit ramp and this ramp has high traffic volume, it can be less operationally favorable to extend and terminate the auxiliary lane at this entrance/exit ramp location. Instead, dropping the auxiliary lane before this entrance/exit ramp represents a more operationally effective option.     

Time-dependent drivers’ merging behavior model in work zone merging areas

This study investigates the drivers’ merging behavior in work zone merging areas during the entire merging implementation period from the time of starting a merging maneuver to that of completing the maneuver. With the actual work zone merging traffic data, we propose a time-dependent logistic regression model considering the possible time-varying effects of influencing factors, and a standard logistic regression model for the purpose of model comparison. Model comparison results show that the time-dependent model performs better than the standard model because the former can provide higher prediction accuracy. The time-dependent model results show that seven factors exhibit time-varying effects on the drivers’ merging behavior, including merging vehicle speed, through lane lead vehicle speed and through lane lag vehicle speed, longitudinal gap between the merging and lead vehicles, longitudinal gap between the merging and through lane lead vehicles, types of through lane lead and through lane lag vehicles. Interestingly, both the through lane lead vehicle speed and the through lane lag vehicle speed are found to exhibit heterogeneous effects at different times of the merging implementation period. One important finding from this study is that the merging vehicle has a decreasing willingness to take the choice of “complete a merging maneuver” as the elapsed time increases if the through lane lead vehicle is a heavy vehicle.     

Comments on flow characteristics on acceleration lanes

This paper deals with driver behavior while travelling on and merging from acceleration lanes. Two possible groups of drivers were identified: drivers who always perform the merging maneuver during the second part of the acceleration lane, regardless of whether an appropriate gap or lag was available to them previously. Three components of the aggregated delay for the merging process were suggested and evaluated. A method of estimating the random delay and travel time on acceleration lane was proposed and evaluated against an aggregated empirical data obtained on three freeway acceleration lanes. An evaluation of the contribution of the ramp volume to the traffic delay was also performed and discussed and a graph which may be of practical use for road and traffic engineers in assessing the expected influence of various ramp and freeway volume combinations is presented.     

A Cooperative Intelligent Transport Systems (C‐ITS)‐based lane‐changing advisory for weaving sections

Weaving sections, a common design of motorways, require extensive lane‐change manoeuvres. Numerous studies have found that drivers tend to make their lane changes as soon as they enter the weaving section, as the traffic volume increases. Congestion builds up as a result of this high lane‐changing concentration. Importantly, such congestion also limits the use of existing infrastructure, the weaving section downstream. This behaviour thus affects both safety and operational aspects. The potential tool for managing motorways effectively and efficiently is cooperative intelligent transport systems (C‐ITS). This research investigates a lane‐change distribution advisory application based on C‐ITS for weaving vehicles in weaving sections. The objective of this research is to alleviate the lane‐changing concentration problem by coordinating weaving vehicles to ensure that such lane‐changing activities are evenly distributed over the existing weaving length. This is achieved by sending individual messages to drivers based on their location to advise them when to start their lane change. The research applied a microscopic simulation in aimsun to evaluate the proposed strategy's effectiveness in a one‐sided ramp weave. The proposed strategy was evaluated using different weaving advisory proportions, traffic demands and penetration rates. The evaluation revealed that the proposed lane‐changing advisory has the potential to significantly improve delay. Copyright © 2016 John Wiley & Sons, Ltd.     

Investigations of interactions between bus rapid transit and general traffic flows

Bus rapid transit (BRT) is a popular strategy to increase transit attraction because of its high‐capacity, comfortable service, and fast travel speed with the exclusive right‐of‐way. Various engineering designs of right‐of‐way and the violation enforcement influence interactions between BRT and general traffic flows. An empirical assessment framework is proposed to investigate traffic congestion and lane‐changing patterns at one typical bottleneck along a BRT corridor. The BRT bottleneck consists of bus lane, BRT station, video enforcement zone, and transit signal priority intersection. We analyze oblique cumulative vehicle counts and oblique cumulative lane‐changing maneuvers extracted from videos. The cumulative vehicle counts method widely applied in revealing queueing dynamics at freeway bottlenecks is extended to an urban BRT corridor. In the study site, we assume four lane‐changing patterns, three of which are verified by the empirical measurements. Investigations of interactions between buses and general traffic show that abnormal behaviors (such as lane violations and slow moving of the general traffic) induce 16% reduction in the saturation rate of general traffic and 17% increase in bus travel time. Further observations show that the BRT station and its induced increasing lane‐changing maneuvers increase the downstream queue discharge flows of general traffic. The empirical results also contribute to more efficient strategies of BRT planning and operations, such as alternative enforcement methods, various lane separation types, and optimized traffic operations. Copyright © 2014 John Wiley & Sons, Ltd.     

A decentralized control strategy for freeway regulation

A multilevel decentralized control scheme, the cascading technique, with application to the regulation of traffic on an urban freeway is presented. Performance of the decentralized system is compared to the performance of a centralized and a fixed time control structure. It is shown that the decentralized structure performs better than the centralized structure when incidents (lane closures) occur on the freeway. The freeway is modeled in terms of the aggregate variables section density and section speed, and is considered as a system of interconnected subsystems.     

Dual influences on vehicle speed in special-use lanes and critique of US regulation

We verify that slow speeds in a special-use lane, such as a carpool or bus lane, can be due to both, high demand for that lane and slow speeds in the adjacent regular-use lane. These dual influences are confirmed from months of data collected from all freeway carpool facilities in the San Francisco Bay Area. Additional data indicate that both influences hold: for other types of special-use lanes, including bus lanes; and for other parts of the world.The findings do not bode well for a new US regulation stipulating that most classes of Low-Emitting Vehicles, or LEVs, are to vacate slow-moving carpool lanes. These LEVs invariably constitute small percentages of traffic; e.g. they are only about 1% of the freeway traffic demand in the San Francisco Bay Area. Yet, we show: that relegating some or all of these vehicles to regular-use lanes can significantly add to regular-lane congestion; and that this, in turn, can also be damaging to vehicles that continue to use the carpool lanes. Counterproductive outcomes of this kind are predicted first by applying kinematic wave analysis to a real Bay Area freeway. Its measured data indicate that the site selected for this analysis stands to suffer less from the regulation than will others in the region. Yet, we predict: that the regulation will cause the site’s people-hours and vehicle-hours traveled during the rush to each increase by more than 10%; and that carpool-lane traffic will share in the damages. Real data from the site support these predictions. Further parametric analysis of a hypothetical, but more generic freeway system indicates that these kinds of negative outcomes will be widespread. Constructive ways to amend the new regulation are discussed, as are promising strategies to increase the vehicle speeds in carpool lanes by improving the travel conditions in regular lanes.     

Effects of low speed limits on freeway traffic flow

Recent years have seen a renewed interest in Variable Speed Limit (VSL) strategies. New opportunities for VSL as a freeway metering mechanism or a homogenization scheme to reduce speed differences and lane changing maneuvers are being explored. This paper examines both the macroscopic and microscopic effects of different speed limits on a traffic stream, especially when adopting low speed limits. To that end, data from a VSL experiment carried out on a freeway in Spain are used. Data include vehicle counts, speeds and occupancy per lane, as well as lane changing rates for three days, each with a different fixed speed limit (80 km/h, 60 km/h, and 40 km/h). Results reveal some of the mechanisms through which VSL affects traffic performance, specifically the flow and speed distribution across lanes, as well as the ensuing lane changing maneuvers. It is confirmed that the lower the speed limit, the higher the occupancy to achieve a given flow. This result has been observed even for relatively high flows and low speed limits. For instance, a stable flow of 1942 veh/h/lane has been measured with the 40 km/h speed limit in force. The corresponding occupancy was 33%, doubling the typical occupancy for this flow in the absence of speed limits. This means that VSL strategies aiming to restrict the mainline flow on a freeway by using low speed limits will need to be applied carefully, avoiding conditions as the ones presented here, where speed limits have a reduced ability to limit flows. On the other hand, VSL strategies trying to get the most from the increased vehicle storage capacity of freeways under low speed limits might be rather promising. Additionally, results show that lower speed limits increase the speed differences across lanes for moderate demands. This, in turn, also increases the lane changing rate. This means that VSL strategies aiming to homogenize traffic and reduce lane changing activity might not be successful when adopting such low speed limits. In contrast, lower speed limits widen the range of flows under uniform lane flow distributions, so that, even for moderate to low demands, the under-utilization of any lane is avoided. These findings are useful for the development of better traffic models that are able to emulate these effects. Moreover, they are crucial for the implementation and assessment of VSL strategies and other traffic control algorithms.     

Impact of heavy vehicles on surrounding traffic characteristics

This work examines the impact of heavy vehicle movements on measured traffic characteristics in detail. Although the number of heavy vehicles within the traffic stream is only a small percentage, their impact is prominent. Heavy vehicles impose physical and psychological effects on surrounding traffic flow because of their length and size (physical) and acceleration/deceleration (operational) characteristics. The objective of this work is to investigate the differences in traffic characteristics in the vicinity of heavy vehicles and passenger cars. The analysis focuses on heavy traffic conditions (level of service E) using a trajectory data of highway I‐80 in California. The results show that larger front and rear space gaps exist for heavy vehicles compared with passenger cars. This may be because of the limitations in manoeuvrability of heavy vehicles and the safety concerns of the rear vehicle drivers, respectively. In addition, heavy vehicle drivers mainly keep a constant speed and do not change their speed frequently. This work also examines the impact of heavy vehicles on their surrounding traffic in terms of average travel time and number of lane changing manoeuvres using Advanced Interactive Microscopic Simulator for Urban and Non‐Urban Networks (AIMSUN) microscopic traffic simulation package. According to the results, the average travel time increases when proportion of heavy vehicles rises in each lane. To reflect the impact of heavy vehicles on average travel time, a term related to heavy vehicle percentage is introduced into two different travel time equations, Bureau of Public Roads and Akçelik's travel time equations. The results show that using an exclusive term for heavy vehicles can better estimate the travel times for more than 10%. Finally, number of passenger car lane changing manoeuvres per lane will be more frequent when more heavy vehicles exist in that lane. The influence of heavy vehicles on the number of passenger car lane changing is intensified in higher traffic densities and higher percentage of heavy vehicles. Large numbers of lane changing manoeuvres can increase the number of traffic accidents and potentially reduce traffic safety. The results show an increase of 5% in the likelihood of accidents, when percentage of heavy vehicles increases to 30% of total traffic. Copyright © 2014 John Wiley & Sons, Ltd.     

基于元胞自动机的双车道变道交通流特性研究

在庞杂的城市交通环境下,驾驶员为了寻求更快的速度,常常采用主动的换道行为。由于汽车使用量逐年增长,换道引起的交通事故经常发生。研究车辆变道行为,寻求有效措施减少交通事故的发生,对提高道路安全性具有积极的意义。本文以多车道系统中车辆变道行为为研究对象,以元胞自动机理论为基础,对比分析单向单车道、单向双车道换道行为,并运用MATLAB仿真软件进行分析,获得变道交通流的相关特性曲线。     

A hybrid controller for autonomous vehicles driving on automated highways

This paper addresses the problem of the hybrid control of autonomous vehicles driving on automated highways. Vehicles are autonomous, so they do not communicate with each other nor with the infrastructure. Two problems have to be dealt with: a vehicle driving in a single-lane highway must never collide with its leading vehicle; and a vehicle entering the highway at a designated entry junction must be able to merge from the merging lane to the main lane, again without any collision. To solve these problems, we equip each vehicle with a hybrid controller, consisting of several continuous control laws embedded inside a finite state automaton. The automaton specifies when a given vehicle must enter the highway, merge into the main lane, yield to other vehicles, exit from the highway, and so on. The continuous control laws specify what acceleration the vehicle must have in order to avoid collisions with nearby vehicles. By carefully designing these control laws and the conditions guarding the automaton transitions, we are able to demonstrate three important results. First, we state the initial conditions guaranteeing that a following vehicle never collides with its leading vehicle. Second, we extend this first result to a lane of autonomous vehicles. Third, we prove that if all the vehicles are equipped with our hybrid controller, then no collision can ever occur, and all vehicles either merge successfully or are forced to drop out when they reach the end of their merging lane. Finally, we show the outcome of a highway microsimulation modelled after the Katy Corridor near Houston, Texas: our single-lane highway can accommodate 4000 vehicles per hour with neither drop-outs nor traffic congestion. It is entirely programmed in SHIFT, a hybrid systems simulation language developed at UC Berkeley by the PATH group. This shows that SHIFT is a well suited language for designing safe control laws for autonomous highway systems, among others.     

高原地区公路运行速度模型研究

文章基于对青藏公路车辆运行速度、车辆组成的调查,采用层次分析法对不同车辆组成、不同路段速度进行分析,建立了不同车辆组成下的运行速度模型,并结合交通事故数据,提出了确保交通安全的常年冻土区公路运行速度值。该运行速度模型的应用研究,为减少道路交通事故提供了一种新思路。     

A problem of limited-access special lanes. Part I: Spatiotemporal studies of real freeway traffic

Most special-use freeway lanes in the US, whether reserved for carpools, toll-paying commuters or both, are physically separated from the adjacent regular-use lanes by some form of barrier. Vehicle movements in and out of a special lane of this type are permitted only at select access points along the route. The barrier at each select point might open for a distance of 400 m or so. Limiting access in this way is said to reduce the “turbulence” that might otherwise occur were the special lane not to have a barrier, such that vehicles could instead enter or exit that lane anywhere along its length.Yet, real freeway traffic studied in spatiotemporal fashion shows that access points are prone to become bottlenecks. The problem occurs when traffic in the regular lanes becomes dense, as commonly happens during a rush. Drivers then seek refuge in the special lane in greater numbers. Since the vehicular maneuvers through the access point are focused within a limited physical space, they can become disruptive and further degrade traffic. Degradation can occur both in the special lane and in the adjacent regular ones. The damage can be worse than when there is no barrier to limit special-lane ingress and egress.The problem is shown to be reproducible across sites and across days at each site. Policy implications are discussed. Select designs and policies to address the problem are thereafter explored in Part II of the paper using traffic simulation.