Cycleways and footpaths: What separation is needed for equivalent air pollution dose between travel modes?

Cycling and walking are being promoted in many urban areas as alternatives to motorised transport for health, environmental, and financial reasons. The reduced congestion and resulting decrease in the overall amount of pollution reduced can be expected to result in health benefits for the community. However, active commuters, due to their increased respiration rates and often increased travel times can expect to receive larger doses of air pollution compared with those using motorised forms of transport. However, given the large dropoff in concentrations away from a road, it can be expected that significant reductions can be achieved even with relatively small increases in separation between the path of cyclists/pedestrians and motor vehicles.This study presents a simple methodology for calculating the separation needed for cyclists and pedestrians to experience the same air pollution dose as car commuters. An example is given based on carbon monoxide (CO) data collected in a field campaign consisting of a car driver, a cyclist and a pedestrian travelling on a 2600 metre loop of road in Auckland. For this case study, the estimated distance from the centreline needed for cyclists and pedestrians to receive an equivalent dose of CO as motorists was found to range from 5.8 to 14.2 m depending on the commuting mode and the dispersion state of the atmosphere at the site. This was equal to a CO concentration reduction of 0.1–0.14 ppm per metre. Recommendations on facility modifications and route selections have been made to make active mode commuting safer.     

The effects of physical activity on greenhouse gas emissions for common transport modes in European countries

This paper applies a life cycle methodology to estimate activity-related contributions of transport modes to GHG emissions. The methodology uses national input–output tables, environmental accounts, household budget data and nutritional data to derive food-sector GHG coefficients of consumption for ten European countries. The food energy requirements for each mode of transport are estimated taking account of the modal activity level and energy requirements. Typical national food energy-related emissions for walking, cycling, and driving ranged from 25.6 to 77.3 gCO₂-eq/pass.km, 10.4–31.4 gCO₂-eq/pass.km and 1.7–5.2 gCO₂-eq/pass.km; passenger transport was found to result in no food-related emissions above those for a resting individual. Emissions vary between countries depending on the emissions intensities of their energy sectors as well as food prices and average body weights. A life cycle assessment of modal emissions in the UK is undertaken using the food-energy emissions intensities estimated and car travel was found to have the highest emissions intensity, followed by bus, cycling and walking.     

Do modes of transportation and GPS affect cognitive maps of Londoners?

Legibility has long been recognized as an important factor in creating a good image of a city in individuals’ minds. This image is perceived to assist people in understanding the city, finding their way, and recalling the city. The quality of the image affects individuals’ abilities in way-finding. This is especially important for cosmopolitan and global cities such as London in order to preserve resources and time, manage travel costs, limit pollution (air or noise) and enhance these cities as places to live, work and visit. This research examines the cognitive maps of London drawn by a sample of its residents to discover how different modes of transportation and GPS usage could affect individuals’ urban images. Such research is useful for town planners, local government departments, and urban and transport planners because of the way it considers the legibility of London as and provides a tool to study individuals’ urban images. 101 participants were recruited with at least a two-year residency from both genders (38.6% females and 61.4% males) with the average age of 33.88 and S.D. = 10.63. The results suggest car use has a positive correlation with seeing London in city scale and GPS usage has a negative correlation. Whilst recent studies have shown that there are differences between active travel modes (e.g., walking, bicycle riding or driving a car) and passive modes (e.g., as a passenger taking a bus, train or taxi), this study indicates that GPS usage also influences cognitive maps, with a negative correlation found between GPS usage and drawing maps on a city scale. Other significant associations were found for the car drivers with a positive relation with the number of roads mentioned on the maps, seeing London in city scale and having a two-dimensional façade image of the city in mind.     

Tracking daily travel; Assessing discrepancies between GPS-derived and self-reported travel patterns

Global Positioning Systems (GPS) technologies have been used in conjunction with traditional one- or two-day travel diaries to audit respondent reporting patterns, but we used GPS-based monitoring to conduct the first assessment to our knowledge of travel reporting patterns using a seven-day travel log instrument, which could reduce response burden and provide multiple-day, policy-relevant information for evaluation studies. We found substantial agreement between participant-reported daily travel patterns and GPS-derived patterns among 116 adult residents of a largely low-income and non-white transportation corridor in urbanized Los Angeles in 2011–2013. For all modes, the average difference between daily GPS- and log-derived trip counts was only about 0.39 trips and the average difference between daily GPS- and log-derived walking duration was about −11.8 min. We found that the probability that a day would be associated with agreement or discrepancies between these measurement tools varied by travel mode and participant socio-demographic characteristics. Future research is needed to investigate the potential and limitations of this and other self-report instruments for a larger sample and a wider range of population groups and travel patterns.     

Effects of e-bikes on bicycle use and mode share

In Norway, as in many countries, a political goal is to increase bicycle use, and the e-bike is promising in this respect. However, concerns have been raised about mode-share effects. It has been argued that if the e-bike’s only function is in cycling becoming cycling with electric assistance, there would be no benefit to either the environment or public health. Little is yet known about the use of the e-bike, or of its potential in reducing motorized travel. In the current study, 66 randomly selected participants were given an e-bike to use for a limited period of time and the results compared with those of a control group (N = 160). E-bike cycling trips increased from 0.9 to 1.4 per day, distance from 4.8 km to 10.3 km and, as a share of all transport, from 28% to 48%, whereas with the control group there was no increase in cycling. The effect of the e-bike increased with time, indicating a learning effect among users, and was greater for female than for male cyclists. There were no differences with age. Overall, the results suggest that the e-bike is indeed practical for everyday travel.     

The influence of individuals’ environmental attitudes and urban design features on their travel patterns in sustainable neighborhoods in the UK

This paper explores the influence of individuals’ environmental attitudes and urban design features on travel behavior, including mode choice. It uses data from residents of 13 new neighborhood UK developments designed to support sustainable travel. It is found that almost all respondents were concerned about environmental issues, but their views did not necessarily ‘match’ their travel behavior. Individuals’ environmental concerns only had a strong relationship with walking within and near their neighborhood, but not with cycling or public transport use. Residents’ car availability reduced public transport trips, walking and cycling. The influence of urban design features on travel behaviors was mixed, higher incidences of walking in denser, mixed and more permeable developments were not found and nor did residents own fewer cars than the population as a whole. Residents did, however, make more sustainable commuting trips than the population in general. Sustainable modes of travel were related to urban design features including secured bike storage, high connectivity of the neighborhoods to the nearby area, natural surveillance, high quality public realm and traffic calming. Likewise the provision of facilities within and nearby the development encouraged high levels of walking.     

The effect of non-recreational transport cycling on use of other transport modes: A cross-sectional on-line survey

Accurate modelling of the health and environmental benefits of non-recreational transport cycling requires information about its effects on the use of other transport modes. Relevant research has not focussed on cycling for transport in a general context (as opposed to bikeshare), nor allowed for multi-modal trips. The influence of trip- and personal-characteristics on whether cycling replaces car-driving have yet to be considered. The present study aimed to address these research gaps. An on-line cross-sectional survey was completed by 1525 Australians who cycle for transport at least once per week. For the most recent trip completed (at least partly) by bicycle participants provided trip distance, and percentage travelled by car, public transport (PT), and walking. They also provided the percentage travelled by each mode for the same trip before taking up transport cycling; and a hypothetical future trip when riding is not possible. Compared to the same trip before, fifty percent of recent trips reduced car use, and around 1/3 eliminated a 100%-car trip. Reduced car use was significantly less likely for trips under 7.5 km, commuting, females, respondents under 55, and regular cyclists. Reduced car use was less likely for respondents who started riding because it is flexible, and more likely for those who started riding to avoid parking. Car-use was reduced by an average of 6.2 km per trip, and each bicycle-km cycled replaced 0.5 car-km. Participants report that since taking up cycling, even when they cannot use their bike, they use cars less and use PT more compared to before they took up cycling. Results suggest that previous studies underestimated the extent to which transport cycling replaces car travel, and highlights trip types and population groups to target with cycling promotion strategies. Information about the per-trip and per-bicycle-km replacement of car, PT and walking may be used for more accurate estimation of the benefits of transport cycling than has hitherto been possible.     

Would personal carbon trading reduce travel emissions more effectively than a carbon tax?

The application of personal carbon trading (PCT) to transport choices has recently been considered in the literature as a means of reducing CO₂ emissions. Its potential effectiveness in changing car travel behavior is compared to the conventional carbon tax (CT) by means of a stated preferences survey conducted among French drivers (N ∼ 300). We show evidence that PCT could effectively change travel behavior and hence reduce transport emissions from personal travel. There is however a definite reluctance to reduce car travel. We were unable to demonstrate any significant difference between the effectiveness of PCT and the CT with regard to changing travel behavior. However, in the experiment, the PCT scheme provided consistent results while this was not the case for the CT scheme. Further research is needed into the “social norm” conveyed by a personal emissions allowance.     

Maximizing net benefits for conventional and flexible bus services

Transit ridership is usually sensitive to fares, travel times, waiting times, and access times, among other factors. Therefore, the elasticities of demand with respect to such factors should be considered in modeling bus transit services and must be considered when maximizing net benefits (i.e. “system welfare” = consumer surplus + producer surplus) rather just minimizing costs. In this paper welfare is maximized with elastic demand relations for both conventional (fixed route) and flexible-route services in systems with multiple dissimilar regions and periods. As maximum welfare formulations are usually too complex for exact solutions, they have only been used in a few studies focused on conventional transit services. This limitation is overcome here for both conventional and flexible transit services by using a Real Coded Genetic Algorithm to solve such mixed integer nonlinear welfare maximization problems with constraints on capacities and subsidies. The optimized variables include service type, zone sizes, headways and fares. We also determine the maximum welfare threshold between optimized conventional and flexible services) and explore the effects of subsidies. The proposed planning models should be useful in selecting the service type and optimizing other service characteristics based on local geographic characteristics and financial constraints.     

How wide should be the adjacent area to an urban motorway to prevent potential health impacts from traffic emissions?

In recent years, several studies show that people who live, work or attend school near the main roadways have an increased incidence and severity of health problems that may be related with traffic emissions of air pollutants. The concentrations of near-road atmospheric pollutants vary depending on traffic patterns, environmental conditions, topography and the presence of roadside structures. In this study, the vertical and horizontal variation of nitrogen dioxide (NO₂) and benzene (C₆H₆) concentration along a major city ring motorway were analysed. The main goal of this study is to try to establish a distance from this urban motorway considered “safe” concerning the air pollutants human heath limit values and to study the influence of the different forcing factors of the near road air pollutants transport and dispersion. Statistic significant differences (p = 0.001, Kruskal–Wallis test) were observed between sub-domains for NO₂ representing different conditions of traffic emission and pollutants dispersion, but not for C₆H₆ (p = 0.335). Results also suggest significant lower concentrations recorded at 100 m away from roadway than at the roadside for all campaigns (p < 0.016 (NO₂) and p < 0.036 (C₆H₆), Mann–Whitney test). In order to have a “safe” life in homes located near motorways, the outdoor concentrations of NO₂ must not exceed 44–60.0 μg m⁻³ and C₆H₆ must not exceed 1.4–3.3 μg m⁻³. However, at 100 m away from roadway, 81.8% of NO₂ receptors exceed the annual limit value of human health protection (40 μg m⁻³) and at the roadside this value goes up to 95.5%. These findings suggest that the safe distance to an urban motorway roadside should be more at least 100 m. This distance should be further studied before being used as a reference to develop articulated urban mobility and planning policies.     

Travel mode choices in small cities of China: A case study of Changting

The existing literature on urban transportation planning in China focuses primarily on large cities and neglects small cities. This paper aims to fill part of the knowledge gap by examining travel mode choice in Changting, a small city that has been experiencing fast spatial expansion and growing transportation problems. Using survey data collected from 1470 respondents on weekdays and weekends, the study investigates the relationship between mode choice and individuals’ socio-economic characteristics, trip characteristics, attitudes, and home and workplace built environments. While more than 35 percent of survey respondents are car owners, walk, bicycle, e-bike, and motorcycle still account for over 85 percent of trips made during peak hours. E-bike and motorcycle are the dominant means of travel on weekdays, but many people shift to walking and cycling on weekends, making non-motorized and semi-motorized travel especially important for non-commuting trips. Results of multinomial logistic regression show that: (1) job-housing balance might exert different effects on mode choice in different types of urban areas; (2) negative attitude towards e-bike and motorcycle is associated with more walking and cycling; and (3) land use diversity of workplace is related to commuting mode choice on weekdays, while land use diversities of both residential and activity places do not significantly affect mode choice on weekends. Our findings imply that planning and design for small cities needs to differentiate land use and transportation strategies in various types of areas, and to launch outreach programs to shift people’s mode choice from motorized travel to walking and cycling.     

Hitting the sweet spot: Variability in commute lengths and vehicle emissions across a diverse state

In this paper we consider travel across Virginia and identify sustainability “sweet spots” where commute lengths and vehicle emissions per mile combine to maximize green travel in terms of total CO₂ emissions associated with commuting. The analysis is conducted across local voter precincts (N = 2373 in the state) because they are a useful proxy for neighborhoods and well-sized for implementing policy designed to encourage sustainable travel behavior. Virginia is especially appropriate for an examination of variability in sustainable travel behavior and technologies because the state’s transportation, demographic, and political patterns are particularly diverse and have been changing rapidly. We identify four Virginia precinct-based sustainability clusters: Sweet Spots, Emerging Sweet Spots, Neutral and Non-sustaining. A model of demographic differences among the clusters shows that sustainability outcomes, understood in terms of both local commute behavior and vehicle emissions, are significantly associated with the diverse demography and politics of the state. We also look at changes in transportation sustainability and socio-demographic trends within the clusters over the past half-decade, showing that differences in sustainability and demographic metrics are actually accelerating within the state over time. We conclude with a discussion of the implications of the differences among the clusters for developing and implementing effective transportation sustainability policies across the state.     

Understanding travel behaviour change during mega-events: Lessons from the London 2012 Games

This paper presents results from a longitudinal study of the travel behaviour change associated with the London 2012 Olympic and Paralympic Games (the ‘Games’). The research examines commuter travel behaviour through a panel approach enabling an understanding of individual behaviour across three waves (before, during and after), with the study utilising unique access to a Transport for London panel study (n = 1132). The findings indicate that a substantial amount of change occurred during the Games (54% made at least one change), with reducing or re-timing journeys being the most likely adaptations made. A key objective of this work was to advance the discussion about the theoretical constructs that are most applicable in the study of behaviour change associated with disruptive events, which was done through the application and critical evaluation of the Transtheoretical Model. The insights from the stages of change element of the model were relatively limited but the analysis shows significant differences in the underlying factors explaining change according to the type of change made (reduce, re-time, re-mode and re-route). Whilst the long-term behavioural impacts of events like the Games appear small, the study has uncovered a need to consider these behavioural choices as distinct rather than under the collective term of “travel behaviour change”, as is current practice.     

Stochastic dynamic switching in fixed and flexible transit services as market entry-exit real options

The first analytical stochastic and dynamic model for optimizing transit service switching is proposed for “smart transit” applications and for operating shared autonomous transit fleets. The model assumes a region that requires many-to-one last mile transit service either with fixed-route buses or flexible-route, on-demand buses. The demand density evolves continuously over time as an Ornstein-Uhlenbeck process. The optimal policy is determined by solving the switching problem as a market entry and exit real options model. Analysis using the model on a benchmark computational example illustrates the presence of a hysteresis effect, an indifference band that is sensitive to transportation system state and demand parameters, as well as the presence of switching thresholds that exhibit asymmetric sensitivities to transportation system conditions. The proposed policy is computationally compared in a 24-hour simulation to a “perfect information” set of decisions and a myopic policy that has been dominant in the flexible transit literature, with results that suggest the proposed policy can reduce by up to 72% of the excess cost in the myopic policy. Computational experiments of the “modular vehicle” policy demonstrate the existence of an option premium for having flexibility to switch between two vehicle sizes.     

Exploring the link between the neighborhood typologies,bicycle infrastructure and commuting cycling over time and the potential impact on commuter GHG emissions

This paper investigates the evolution of urban cycling in Montreal, Canada and its link to both built environment indicators and bicycle infrastructure accessibility. The effect of new cycling infrastructure on transport-related greenhouse gas (GHG) emissions is then explored. More specifically, we aim at investigating how commuting cycling modal share has evolved across neighborhood built-environment typologies and over time in Montreal, Canada. For this purpose, automobile and bicycle trip information from origin–destination surveys for the years 1998, 2003 and 2008 are used. Neighborhood typologies are generated from different built environment indicators (population and employment density, land use diversity, etc.). Furthermore, to represent the commuter mode choice (bicycle vs automobile), a standard binary logit and simultaneous equation modeling approach are adopted to represent the mode choice and the household location. Among other things, we observe an important increase in the likelihood to cycle across built environment types and over time in the study region. In particular, urban and urban-suburb neighborhoods have experienced an important growth over the 10 years, going from a modal split of 2.8–5.3% and 1.4–3.0%, respectively. After controlling for other factors, the model regression analysis also confirms the important increase across years as well as the significant differences of bicycle ridership across neighborhoods. A statistically significant association is also found between the index of bicycle infrastructure accessibility and bike mode choice – an increase of 10% in the accessibility index results in a 3.7% increase in the ridership. Based on the estimated models and in combination with a GHG inventory at the trip level, the potential impact of planned cycling infrastructure is explored using a basic scenario. A reduction of close to 2% in GHG emissions is observed for an increase of 7% in the length of the bicycle network. Results show the important benefits of bicycle infrastructure to reduce commuting automobile usage and GHG emissions.     

Carbon emission from urban passenger transportation in Beijing

Urban passenger transport significantly contributes to global greenhouse gas emissions, especially in developing countries owing to the rapid motorization, thus making it an important target for carbon reduction. This article established a method to estimate and analyze carbon emission from urban passenger transport including cars, rail transit, taxis and buses. The scope of research was defined based on car registration area, transport types and modes, the stages of rail transit energy consumption. The data availability and gathering were fully illustrated. A city level emission model for the aforementioned four modes of passenger transport was formulated, and parameters including emission factor of electricity and fuel efficiency were tailored according to local situations such as energy structure and field survey. The results reveal that the emission from Beijing’s urban passenger transport in 2012 stood at 15 million tonnes of CO₂, of which 75.5% was from cars, whereas car trip sharing constitutes only 42.5% of the total residential trips. Bus travel, yielding 28.6 g CO₂, is the most efficient mode of transport under the current situations in terms of per passenger kilometer (PKM) emission, whereas car or taxi trips emit more than 5 times that of bus trips. Although a decrease trend appears, Beijing still has potential for further carbon reduction in passenger transport field in contrast to other cities in developed countries. Development of rail transit and further limitation on cars could assist in reducing 4.39 million tonnes CO₂ emission.     

Wireless charging in California: Range,recharge, and vehicle electrification

This research evaluated the potential for wireless dynamic charging (charging while moving) to address range and recharge issues of modern electric vehicles by considering travel to regional destinations in California. A 200-mile electric vehicle with a real range of 160 miles plus 40 miles reserve was assumed to be used by consumers in concert with static and dynamic charging as a strict substitute for gasoline vehicle travel. Different combinations of wireless charging power (20–120 kW) and vehicle range (100–300 miles) were evaluated. One of the results highlighted in the research indicated that travel between popular destinations could be accomplished with a 200-mile EV and a 40 kW dynamic wireless charging system at a cost of about $2.5 billion. System cost for a 200-mile EV could be reduced to less than $1 billion if wireless vehicle charging power levels were increased to 100 kW or greater. For vehicles consuming 138 kWh of dynamic energy per year on a 40 kW dynamic system, the capital cost of $2.5 billion plus yearly energy costs could be recouped over a 20-year period at an average cost to each vehicle owner of $512 per year at a volume of 300,000 vehicles or $168 per year at a volume of 1,000,000 vehicles. Cost comparisons of dynamic charging, increased battery capacity, and gasoline refueling were presented. Dynamic charging, coupled with strategic wayside static charging, was shown to be more cost effective to the consumer over a 10-year period than gasoline refueling at $2.50 or $4.00 per gallon. Notably, even at very low battery prices of $100 per kWh, the research showed that dynamic charging can be a more cost effective approach to extending range than increasing battery capacity.     

Using nonparametrics to specify a model to measure the value of travel time

Using a range of nonparametric methods, the paper examines the specification of a model to evaluate the willingness-to-pay (WTP) for travel time changes from binomial choice data from a simple time–cost trading experiment. The analysis favours a model with random WTP as the only source of randomness over a model with fixed WTP which is linear in time and cost and has an additive random error term. Results further indicate that the distribution of log WTP can be described as a sum of a linear index fixing the location of the log WTP distribution and an independent random variable representing unobserved heterogeneity. This formulation is useful for parametric modelling. The index indicates that the WTP varies systematically with income and other individual characteristics. The WTP varies also with the time difference presented in the experiment which is in contradiction of standard utility theory.