Effect on direct injection naturally aspirated diesel engine characteristics fuelled by pine oil,ceiba pentandra methyl ester compared with diesel

This paper explores the experimental investigation of the performance, emission and combustion characteristics of bio fuels from ceiba pentandra methyl ester (CPME), ceiba pentandra methyl ester-pine oil blends (CPMEP) and pine oil and the results are compared with diesel. In ceiba pentandra seed oil the CPME yield is 92% by using transesterification process with the optimum conditions of 560 rpm, reaction time 58 min, catalyst concentration 13 g and methanol amount 500 ml. The viscosity of CPME is high when compare with diesel. So the low viscosity of pine oil is blended with CPME and it can be directly used in diesel engine without any modification. At different loads the Pine oil, CPME and CPMEP blends were used in direct injection naturally aspirated compression ignition engine. The outcomes exhibited that at full load conditions for CPME and CPMEP blends increased brake specific fuel consumption, and decreased brake thermal efficiency, CO, HC emissions. NOx emissions decreased and smoke emissions are increased on CPME and CPMEP blends, expect B25 blend compared with diesel. The combustion analysis like the heat release rate, peak cylinder pressure, cumulative heat release rate and ignition delay for CPME, CPMEP blends slightly lower and combustion duration higher than diesel and pine oil. At the Same engine operating condition, the engine fuelled with pine oil the values of brake thermal efficiency 4.79%, peak cylinder pressure, heat release rate, cumulative heat release rate and ignition delay are increased. Brake specific fuel consumption, CO, HC, and smoke were 9.46%, 16.66%, 14.89% and 8.33% decreased. However, the NOx emission is 8.29% higher than that of diesel. Experimental fuels up to B50 (50% pine oil and 50% CPME) blends have proved good potential for future energy is needed.     

Thermodynamic,environmental and economic effects of diesel and biodiesel fuels on exhaust emissions and nano-particles of a diesel engine

In this study, diesel (JIS#2) and various biodiesel fuels (BDF20, BDF50, BDF100) are used to operate the diesel engine at 100 Nm, 200 Nm and full load; while the engine speed is 1800 rpm. The system is experimentally studied, and the energy, exergy, sustainability, thermoeconomic and exergoeconomic analyses are performed to the system. The Engine Exhaust Particle Sizer is used to measure the size distribution of engine exhaust particle emissions. Also, the data of the exhaust emissions, soot, particle numbers, fuel consumptions, etc. are measured. It is found that (i) most of the exhaust emissions (except NO_x) are directly proportional to the engine load, (ii) maximum CO₂ and NO_x emissions rates are generally determined for the BDF100 biodiesel fuel; while the minimum ones are calculated for the JIS#2 diesel fuel. On the other hand, the maximum CO and HC emissions rates are generally computed for the JIS#2 diesel fuel; while the minimum ones are found for the BDF100 biodiesel fuel, (iii) fuel consumptions from maximum to minimum are BDF100 > BDF50 > BDF20 > JIS#2 at all of the engine loads, (iv) particle concentration of the JIS#2 diesel fuel is higher than the biodiesel fuels, (v) soot concentrations of the JIS#2, BDF20 and BDF50 fuels are directly proportional to the engine load; while the BDF100 is inversely proportional, (vi) system has better energy and exergy efficiency when the engine is operated with the biodiesel fuels (vii) sustainability of the fuels are BDF100 > BDF50 > BDF20 > JIS#2, (viii) thermoeconomic and exergoeconomic parameters rates from maximum to minimum are JIS#2 > BDF20 > BDF50 > BDF100.     

In-use measurement of the activity, fuel use, and emissions of eight cement mixer trucks operated on each of petroleum diesel and soy-based B20 biodiesel

In-use micro-scale fuel use and emission rates were measured for eight cement mixer trucks using a portable emission measurement system. Each vehicle was tested on petroleum diesel and B20 biodiesel. Average fuel use and emission rates increase monotonically versus engine manifold absolute pressure. A typical duty cycle includes loading at a cement plant, transit while loaded from the cement plant to work site, creeping in a queue of vehicles at the worksite, unloading, and transit without load from the site to the plant. For B20 versus petroleum diesel, there is no significant change in the rate of fuel use, CO₂ emissions, and NO emissions, and significant decreases in emissions for CO, hydrocarbons, and particulate matter. For loaded versus unloaded onroad travel, fuel use and CO₂ emissions rates are approximately 60% higher and the rates for other pollutants are approximately 30–50% higher. A substantial portion of cycle emissions occurred at the work site. Inter-vehicle and intra-cycle variability are also quantified using the micro-scale methodology.     

Experimental analysis of exhaust gas after treatment system using water scrubbing in a single cylinder diesel engine for diesel and biofuel blends

A low-cost exhaust gas after treatment system called water-scrubbing is attempted in this paper. An emission treatment setup is fabricated, which is installed in the exhaust of the engine. This takes the exhaust gas and sprays water in the exhaust and passes it through the chamber containing silica gel. An attempt is made to investigate experimentally the performance and emission characteristics of a direct injection (DI) diesel engine, with and without water injection at the exhaust using diesel fuel (DF), diesel-Karanja oil blend (DKB) and diesel-Jatropha oil blend (DJB). The exhaust gas after treatment system helps to reduce NOx, CO and Particulate matter. The performance of the engine has also been monitored to determine whether the engine has any decrease in performance when the setup is used and it is found that there is no change in the engine performance.