The Impact of Container Type Diversification on Regional British Port Development Strategies

Abstract

Despite a concentration of container traffic in the southeast of the UK over the last few decades, regional ports are attempting new development strategies to capture or retain specific traffic segments. These include intra-European short-sea traffic and a potentially increasing feeder market. These trends are reflected in the movement of different container types, which result in a number of planning challenges related to changing infrastructural and operational requirements. This paper uses highly disaggregated data on container type movements to address three issues that can inform these planning challenges. First, the imbalance of trade resulting in empty container repositioning; second, the requirement for gauge-cleared rail routes to cater for the increasing proportion of high-cube containers; and third, the specialisation of European short-sea traffic at secondary UK ports. The results reveal the disproportionate repositioning of empty containers at Scottish ports and the importance of 45?ft, high-cube and pallet-wide containers at regional ports, highlighting their focus on intra-European short-sea traffic and raising difficulties relating to their lower quality of landside infrastructure (particularly rail) in comparison to the large south-eastern ports. The potential repercussions on hinterland infrastructure development raise questions about both public and private sector responses to regional port development.     

Assessing the CO2 impact of current and future rail track in the UK

This paper investigates the CO₂ impact of current and future UK rail track and estimates the material, process and transport emissions associated with construction, maintenance and end-of-life activities for designs at high and low traffic loads. Analysis shows that for current track configurations, track with concrete sleepers has the lowest CO₂ impact, followed by steel, hardwood and softwood. Several potential future rail track designs have been analysed including embedded rail and double and quadruple-headed rail. All future track designs have a lower impact than current designs, but this improvement is more marked at high traffic loads. Up to a 40% reduction in CO₂ impact could be achieved if the UK rail network was to move from conventional track design to a double-headed embedded rail design. Key levers for reducing the CO₂ impact of track are identified as service life extension, traffic load reduction and the selection of low impact track designs.     

Carbon dioxide emissions from port container distribution: Spatial characteristics and driving factors

Port carbon dioxide (CO₂) emissions in China have become an ever-increasing public concern due to their significant impacts on human health and the environment. However, existing studies focus mainly on CO₂ emissions from vessels calling at the ports and cargo handling within the ports, paying little attention to the inland distribution networks. To fill this gap, this paper proposes an easily implemented method for calculating CO₂ emissions from port container distribution (PCD) and investigates their spatial characteristics and driving factors. By analyzing 30 container ports in China, the main findings are as follows. First, road transportation is the major contributor of CO₂ emissions from PCD due to the lack of rail and inland water transportation. Second, PCD carbon emissions exhibit significant local spatial clustering. That is, ports with similar geographical locations tend to present a similar pattern of PCD carbon emissions. Third, as suggested by the spatial Durbin model, PCD carbon emissions are negatively determined by local gross domestic product, number of port berths, but are positively determined by local tertiary industry value and highway freight volume, and waterway freight volume in both local and neighboring ports. These results provide empirical insights into cross-port collaboration in reducing PCD carbon emissions.     

Measuring reliability of transportation networks using snapshots of movements in the network – An analytical and empirical study

In this paper we introduce an analytical framework based on discrete Likelihood Maximization techniques that provides estimates of operational level data of Queuing models and Transportation networks based on snapshots of data on movements of commodities in a network. We apply our methodology to detailed data on movements of containers imported from S.E. Asian ports to marine ports on the west coast of Canada, unloaded at these ports, moved to rail cars, and transported by rail to destinations in U.S. and Canada. We show how one can estimate operational level parameters such as the number of servers at the ports, schedules of departure and capacity of trains, and even speed of trains based on only snapshots of container movements in the network. Subsequently, we were able to calibrate the entire inter-continental transportation network, were able to identify the sources of variability in the network and were able to measure the reliability of the network to shocks.     

A cost and CO2 comparison of using trains and higher capacity trucks when UK FMCG companies collaborate

Companies working in a collaboration are able to achieve higher vehicle capacity utilisation and reduced empty running, resulting in lower costs and improved sustainability through reduced emissions and congestion. Collaboration produces higher volumes of goods to be moved than individual companies which means that further efficiencies may be possible by relaxing the freight mode constraints and considering rail and higher capacity vehicles. This paper explains how real world data has been used in a model to quantify the economic and environmental benefits in the FMCG sector delivered through collaboration utilising road and rail freight modes. Data for one month was provided by 10 FMCG companies and included freight transport flows between depots and customers, inter depot movements, and supplier collections. Detailed road and rail costs and operating characteristics were obtained and, with the transport flows, applied to a network design model which was used to validate the company data sets. A strategy examining the potential use of alternative higher capacity vehicles and rail for the flows between nine regional consolidation centres showed cost and CO₂ savings. Just under half the inter-regional flows benefited from double deck trailers, longer heavier vehicles for 30% of the flows and rail with different wagon configurations for the rest. In summary there was a 23% reduction in cost with 58% fewer road kilometres and a 46% reduction in CO₂ emissions. The ability to backhaul the same mode of transport between most of the regional centres was one of the strengths of this strategy.     

The potential mitigation of CO2 emissions via modal substitution of high-speed rail for short-haul air travel from a life cycle perspective – An Australian case study

The objective of this study is to provide a strategic evaluation of the mitigation of CO₂ emissions via modal substitution of high-speed rail for short-haul air travel on the Sydney–Melbourne, Australia city-pair from a life cycle perspective. It has been demonstrated that when considering CO₂ emissions from vehicle operations, the modal shift from air to high-speed rail on this city-pair has the potential to provide a means of CO₂ mitigation. However, uncertainty exists with regard to the level of mitigation potential when considering the whole-of-life performance of the systems. Given the significant difference in the infrastructure requirements between the air mode and the high-speed rail mode, this study quantifies the life cycle CO₂ load attributable to each system and examines the effect on CO₂ mitigation potential. The study concluded that while the inclusion of the linehaul infrastructure did increase the CO₂ load associated with high-speed rail mode, it did not equate to or exceed the CO₂ load per trip as experienced by the air mode. The avoided annual life cycle CO₂ emission in the target year 2056 was 0.37 Mt representing an 18% reduction when compared to the air mode only on the city pair. In fact, the scenario comparison indicated that the substitution of high-speed rail for short-haul air travel on the city pair resulted in CO₂ emissions avoidance throughout the longitudinal period.     

Examining transport futures with scenario analysis and MCA

Climate change is a global problem and across the world the transport sector is finding it difficult to break projected increases in carbon dioxide (CO₂) emissions; there are very few contexts where deep reductions in transport CO₂ emissions are being made. A number of research studies are now examining the potential for future lower CO₂ emissions in the transport sector. This paper develops this work to consider some of the wider sustainability impacts (economic, social and local environmental) as well as the lower CO₂ transport impacts of different policy trajectories. Hence the central argument made is for an integrated approach to transport policy making over the longer term - incorporating scenario analysis and multi-criteria assessment (MCA) - to help assess likely progress against a range of objectives.The analysis is based on work carried out in Oxfordshire, UK. Different packages of measures are selected and two scenarios developed which satisfy lower CO₂ aspirations, one of which also provides wider positive sustainability impacts. A simulation model has been produced to help explore the strategic policy choices and tensions evident for decision-makers involved in local transport planning. The paper argues for a ‘strategic conversation’ (Van der Heijden, 1996) at the sub-regional and city level, based upon future scenario analysis and MCA, discussing the priorities for intervention. Such an approach will help us examine the scale of change and trade-offs required in moving towards sustainable transport futures.     

Liner shipping network design with emission control areas: A genetic algorithm-based approach

To curb emissions, containerized shipping lines face the traditional trade-off between cost and emissions (CO₂ and SO_x) reduction. This paper considers this element in the context of liner service design and proposes a mixed integer linear programming (MILP) model based on a multi-commodity pickup and delivery arc-flow formulation. The objective is to maximize the profit by selecting the ports to be visited, the sequence of port visit, the cargo flows between ports, as well as the number/operating speeds of vessels on each arc of the selected route. The problem also considers that Emission Control Areas (ECAs) exist in the liner network and accounts for the vessel carrying capacity. In addition to using the MILP solver of CPLEX, we develop in the paper a specific genetic algorithm (GA) based heuristic and show that it gives the possibility to reach an optimal solution when solving large size instances.     

The impact of alternative routeing and packaging scenarios on carbon and sulphate emissions in international wine distribution

There is a large body of research related to carbon footprint reduction in supply chains and logistics from a wide range of sectors; however the decarbonisation of freight transport is mostly explored from a single mode perspective and at a domestic/regional level. This paper takes into account a range of alternative transport modes, routes and methods with particular reference to UK wine imports from two regions: northern Italy and Southeast Australia. The research examines supply chain structures, costs and the environmental impact of international wine distribution to the UK. A number of options are evaluated to calculate the carbon footprint and sulphate emissions of alternative route, mode, method of carriage, and packaging combinations. The estimation of CO₂e emissions incorporates three main elements - cargo mass, distance and method of carriage; sulphate emissions are derived from actual ship routes, engine power and operational speeds. The bottling of wine either at source or close to destination is also taken into consideration. The key findings are: there are major differences between the environmental footprint of different routeing and packaging scenarios; the international shipping leg almost always has a much larger footprint than inland transport within the UK except in the hypothetical case of the rail shipments from Italy using flexitanks. With reference to sulphate, the lowest cost scenario among the sea maximizing options is also the sulphate minimising solution.     

Electric and hydrogen buses: Shifting from conventionally fuelled cars in the UK

For the UK to meet their national target of net zero emissions as part of the central Paris Agreement target, further emphasis needs to be placed on decarbonizing public transport and moving away from personal transport (conventionally fuelled vehicles (CFVs) and electric vehicles (EVs)). Electric buses (EBs) and hydrogen buses (HBs) have the potential to fulfil requirements if powered from low carbon renewable energy sources.A comparison of carbon dioxide (CO₂) emissions produced from conventionally fuelled buses (CFB), EBs and HBs between 2017 and 2050 under four National Grid electricity scenarios was conducted. In addition, emissions per person at different vehicle capacity levels (100%, 75%, 50% and 25%) were projected for CFBs, HBs, EBs and personal transport assuming a maximum of 80 passengers per bus and four per personal vehicle.Results indicated that CFVs produced 30 gCO₂ km⁻¹ per person compared to 16.3 gCO₂ km⁻¹ per person by CFBs by 2050. At 100% capacity, under the two-degree scenario, CFB emissions were 36 times higher than EBs, 9 times higher than HBs and 12 times higher than EVs in 2050. Cumulative emissions under all electricity scenarios remained lower for EBs and HBs.Policy makers need to focus on encouraging a modal shift from personal transport towards sustainable public transport, primarily EBs as the lowest level emitting vehicle type. Simple electrification of personal vehicles will not meet the required targets. Simultaneously, CFBs need to be replaced with EBs and HBs if the UK is going to meet emission targets.     

Container Railfreight Services in North‐west Europe: Diversity of Organizational Forms in a Liberalizing Environment

Abstract

The institutional environment of rail transport has changed as a result of recent European directives, but the changes have taken different forms from one country to another. In the case of international maritime chains, the development of door‐to‐door services makes inland haulage from the loading and discharging ports extremely important, and it highlights the need to reshape the rail freight industry. This paper analyses the degree of involvement of different actors drawn from the maritime industry in developing and commercializing rail services in the changing regulatory environment. Several maritime operators, shipping lines, port‐handling companies and port authorities have been involved in some container rail services since the early days of liberalization. Their commitments take very different forms, however. Whereas contracts are mainly used for the provision of service, particularly for train haulage, integration by means of shareholding or creating subsidiaries or joint ventures is used for marketing. Important differences between France, the UK, Germany and the Netherlands are detailed. In the latter two countries, there is more involvement in the provision of rail services. Marketing rail services appear to be the main strategic issue for the maritime operators in all four countries     

Carbon emission from urban passenger transportation in Beijing

Urban passenger transport significantly contributes to global greenhouse gas emissions, especially in developing countries owing to the rapid motorization, thus making it an important target for carbon reduction. This article established a method to estimate and analyze carbon emission from urban passenger transport including cars, rail transit, taxis and buses. The scope of research was defined based on car registration area, transport types and modes, the stages of rail transit energy consumption. The data availability and gathering were fully illustrated. A city level emission model for the aforementioned four modes of passenger transport was formulated, and parameters including emission factor of electricity and fuel efficiency were tailored according to local situations such as energy structure and field survey. The results reveal that the emission from Beijing’s urban passenger transport in 2012 stood at 15 million tonnes of CO₂, of which 75.5% was from cars, whereas car trip sharing constitutes only 42.5% of the total residential trips. Bus travel, yielding 28.6 g CO₂, is the most efficient mode of transport under the current situations in terms of per passenger kilometer (PKM) emission, whereas car or taxi trips emit more than 5 times that of bus trips. Although a decrease trend appears, Beijing still has potential for further carbon reduction in passenger transport field in contrast to other cities in developed countries. Development of rail transit and further limitation on cars could assist in reducing 4.39 million tonnes CO₂ emission.     

Can ports increase traffic while reducing inputs? Technical efficiency of Spanish Port Authorities using a directional distance function approach

The focus of this paper is on the productive efficiency of ports. We estimate a directional technology distance function using parametric techniques to analyze the production technology and technical efficiency of a set of Spanish Port Authorities observed over the period 1993–2012. Technical inefficiency is conceived as the ability of ports to simultaneously expand a given output and contract variable inputs while maintaining quasi-fixed inputs and other outputs constant. Thus, for containerized cargo we address the following question: Given the amount of quasi-fixed inputs used by the firm and given the volume of the other outputs (liquids, solids, non-containerized cargo and passenger traffic), could ports increase their containerized merchandise while simultaneously reducing their variable inputs? Similar questions are asked for solid bulk and non-containerized general cargo. Our results show evidence of technical inefficiency among the ports in our sample. In particular, if the ports operated efficiently, we find that containerized cargo could be expanded by an average of over 6.4%, with an equivalent reduction in variable inputs. Solid bulk cargo and general non-containerized cargo could be increased by 4.1% and 6.1% respectively, with corresponding reductions in variable inputs. An implication of our results is that there is ample scope for specialization on the part of ports with no increase in infrastructure costs. Given that large investments in infrastructure have been made in Spanish port over the last decade, this opens the possibility of moving towards a management model based on taking advantage of existing capacity rather than new investments.     

Positive impact of distribution centres on the environment

The transport sector in general, and trucks in particular, generates a significant amount of emissions in Australia. It appears the trend will escalate unless different measures are taken to reduce the reliance of freight transport on trucks. This paper discusses the benefits of distribution centres as a means to reduce road congestion, increase safety, protect the environment by reducing atmospheric pollution and improve freight distribution. It also provides the effective use of the existing rail network and its infrastructure and improves the lead-time as well as lowering the cost of transportation of cargo. It also investigates the positive impact of distribution centres located near to manufacturing and farming production units. A simulation model has been developed and used to help determine the amount of atmospheric pollution produced by two modes of land transport, rail and road, for the movement of containers between port and destination. Results derived from the model provide evidence about a preferred land-transport regime. The paper has two sections: (1) the role of distribution centres in the chain of transport and (2) the impact of distribution centres on the environment. The first section investigates the feasibility of the implementation of distribution centres in the State of Victoria with respect to rail line capacity and location allocation. The second section presents an additional simulation model that investigates the role of a distribution centre in relation to the amount of atmospheric pollution produced by rail and road, while containers are carried between port and destination.     

Optimal pricing for priority service and space allocation in container ports

This paper focuses on the determination of optimal space allocation and optimal pricing for priority systems in container ports. The problem is formulated taking into account the intrinsic and logistic cargo value, and a capacity constraint that considers the various physical requirements of the containers. Prices and space allocations are found for various cases, showing explicitly the role of each element. The resulting models extend classical price differentiation theory, i.e. the inverse elasticity rule, in various directions. Finally, the implications of these results and the corresponding information requirements are clearly established.     

The impact of high-speed rail investment on economic and environmental change in China: A dynamic CGE analysis

This study investigates the impact of high-speed rail investment on the economy and environment in China using a computable general equilibrium (CGE) model. The analysis is implemented in a dynamic recursive framework capturing long-run capital accumulation and labor market equilibrium. A national level impact was simulated through direct impact drivers including land use conversion, output expansion, cost reduction, productivity increase, transport demand substitution and induced demand. The results suggest that rail investment in China over the past decade has been a positive stimulus to the economy, while the effect on CO₂ emissions generation has been large. Overall, the economic impacts of rail investment are achieved primarily through induced demand and output expansion, whereas the contribution from a reduction of rail transportation costs and rail productivity increases were modest. In addition, negligible negative impacts were found from land use for rail development and the substitution effect among other modes. Emissions reduction from substitution of rail for other modes was small and offset by output expansion due to lowered rail transport costs and induced demand.     

Estimating the CO2 intensity of intermodal freight transportation

This paper looks at the environmental effects of shifting from road to rail freight transportation. Little data is available to shippers to calculate the potential CO₂ savings of an intermodal shift. In this paper we analyze a data set of more than 400,000 intermodal shipments to calculate the CO₂ intensity of intermodal transportation as a distinct mode. Our results indicate an average intensity of 67 g of CO₂ per ton-mile, but can vary between 29 and 220 g of CO₂ per ton-mile depending on the specific origin–destination lane. We apply the market area concept to explain the variance between individual lane intensities and demonstrate the complexity in predicting the potential carbon savings in a switch from truckload to intermodal.     

The effectiveness and costs of speed reductions on emissions from international shipping

Greenhouse gas emissions from international shipping are an increasing concern. The paper evaluates whether vessel speed reduction can be a potentially cost-effective CO₂ mitigation option for ships calling on US ports. By applying a profit-maximizing equation to estimate route-specific, economically-efficient speeds, we explore policy impacts of a fuel tax and a speed reduction mandate on CO₂ emissions. The profit-maximizing function incorporates opportunity costs associated with speed reduction that go unobserved in more traditional marginal abatement cost analyses. We find that a fuel tax of about $150/ton fuel will lead to average speed-related CO₂ reductions of about 20–30%. Moreover, a speed reduction mandate targeted to achieve 20% CO₂ reduction in the container fleet costs between $30 and $200 per ton CO₂ abated, depending on how the fleet responds to a speed reduction mandate.     

Economic valuation of Well-To-Wheel CO2 emissions from freight transport along the main transalpine corridors

CO₂ emissions are one of the main externalities related to freight transport. Their evaluation is extremely difficult, due to the presence of several scientific and economic uncertainties. This paper discusses the approaches currently adopted by literature to deal with CO₂, proposing a methodology based on a Well-To-Wheel quantification and an economic valuation deriving from a meta-regression. A freight transport analysis is then provided for one of the most critical areas of Europe, the Alps. Here, the different approaches adopted by the single nations determine divergent results in terms of modal shift towards rail and, consequently, CO₂ emissions. An integrated and transnational strategy could lead to better results, avoiding detoured traffic and increasing the share of railway traffic. To this aim, the carbon impacts of three specific alpine-wide measures are evaluated: namely, Alpine Crossing Exchange, Emissions Trading and Differentiated Toll System. In comparison with business-as-usual scenario, the case study reveals a potential CO₂ saving up to more than 600,000 tons and 38 M€ for the year 2030, thus providing policy makers with an integrative transnational tool able to evaluate the long-term carbon impact of their transport decisions.     

Comparing and presenting city-level transportation CO2 emissions using GIS

In 2011, the European Pollutant Release and Transfer Register (E-PRTR) inventory of diffuse emissions became available, providing data on a range of atmospheric emissions at a 5 km resolution across Europe. The data are produced from spatially disaggregated emissions totals for countries, and must be validated before being used at a sub-national level. The UK government maintains a 1 km resolution emissions inventory based on a bottom-up methodology by which a validation is possible. The UK National Atmospheric Emissions Inventory data are used to assess at what geographic scale the new E-PRTR data might be most useful. This paper compares the two data sets and estimates city-level transportation CO₂ emissions for 149 EU cities. We find that at a functional boundary level the two datasets match well.