Highway traffic state estimation with mixed connected and conventional vehicles: Microscopic simulation-based testing

This paper presents a thorough microscopic simulation investigation of a recently proposed methodology for highway traffic estimation with mixed traffic, i.e., traffic comprising both connected and conventional vehicles, which employs only speed measurements stemming from connected vehicles and a limited number (sufficient to guarantee observability) of flow measurements from spot sensors. The estimation scheme is tested using the commercial traffic simulator Aimsun under various penetration rates of connected vehicles, employing a traffic scenario that features congested as well as free-flow conditions. The case of mixed traffic comprising conventional and connected vehicles equipped with adaptive cruise control, which feature a systematically different car-following behavior than regular vehicles, is also considered. In both cases, it is demonstrated that the estimation results are satisfactory, even for low penetration rates.     

The identification and empirical characterization of vehicular (Lagrangian) fundamental diagrams in multilane traffic flow

Traditional macroscopic traffic flow modeling framework adopts the spatial–temporal coordinate system to analyze traffic flow dynamics. With such modeling and analysis paradigm, complications arise for traffic flow data collected from mobile sensors such as probe vehicles equipped with mobile phones, Bluetooth, and Global Positioning System devices. The vehicle‐based measurement technologies call for new modeling thoughts that address the unique features of moving measurements and explore their full potential. In this paper, we look into the concept of vehicular fundamental diagram (VFD) and discuss its engineering implications. VFD corresponds to a conventional fundamental diagram (FD) in the kinematic wave (KW) theory that adopts space–time coordinates. Similar to the regular FD in the KW theory, VFD encapsulates all traffic flow dynamics. In this paper, to demonstrate the full potential of VFD in interpreting multilane traffic flow dynamics, we generalize the classical Edie's formula and propose a direct approach of reconstructing VFD from traffic measurements in the vehicular coordinates. A smoothing algorithm is proposed to effectively reduce the nonphysical fluctuation of traffic states calculated from multilane vehicle trajectories. As an example, we apply the proposed methodology to explore the next‐generation simulation datasets and identify the existence and forms of shock waves in different coordinate systems. Our findings provide empirical justifications and further insight for the Lagrangian traffic flow theory and models when applied in practice. Copyright © 2015 John Wiley & Sons, Ltd.     

Connected vehicle penetration rate for estimation of arterial measures of effectiveness

The Connected Vehicle (CV) technology is a mobile platform that enables a new dimension of data exchange among vehicles and between vehicles and infrastructure. This data source could improve the estimation of Measures of Effectiveness (MOEs) for traffic operations in real-time, allowing to perfectly monitor traffic states after being fully adopted. However, as with any novel technology, the CV adoption will be a gradual process. This research focuses on determining minimum CV technology penetration rates that would guarantee accurate MOE estimates on signalized arterials. First, we present estimation methods for various MOEs such as average speed, number of stops, acceleration noise, and delay, followed by an initial assessment of the penetration rates required to accurately estimate them in undersaturated and oversaturated conditions. Next, we propose a methodology to determine the minimum CV market penetration rates to guarantee accurate MOE estimates as a function of traffic conditions, signal settings, sampling duration, and the MOE variability. A correction factor is also provided to account for small vehicle populations where sampling is done without replacement. The methodology is tested in a simulated segment of the San Pablo Avenue arterial in Berkeley, CA. The outcomes show that the minimum penetration rate required can be estimated within 1% for most MOEs under a wide range of traffic conditions. The proposed methodology can be used to determine if MOE estimates obtained with a portion of CV equipped vehicles can yield accurate enough results. The methodology could also be used to develop and assess control strategies towards improved arterial traffic operations.     

Field implementation feasibility study of cumulative travel‐time responsive (CTR) traffic signal control algorithm

The cumulative travel‐time responsive (CTR) algorithm determines optimal green split for the next time interval by identifying the maximum cumulative travel time (CTT) estimated under the connected vehicle environment. This paper enhanced the CTR algorithm and evaluated its performance to verify a feasibility of field implementation in a near future. Standard Kalman filter (SKF) and adaptive Kalman filter (AKF) were applied to estimate CTT for each phase in the CTR algorithm. In addition, traffic demand, market penetration rate (MPR), and data availability were considered to evaluate the CTR algorithm's performance. An intersection in the Northern Virginia connected vehicle test bed is selected for a case study and evaluated within vissim and hardware in the loop simulations. As expected, the CTR algorithm's performance depends on MPR because the information collected from connected vehicle is a key enabling factor of the CTR algorithm. However, this paper found that the MPR requirement of the CTR algorithm could be addressed (i) when the data are collected from both connected vehicle and the infrastructure sensors and (ii) when the AKF is adopted. The minimum required MPRs to outperform the actuated traffic signal control were empirically found for each prediction technique (i.e., 30% for the SKF and 20% for the AKF) and data availability. Even without the infrastructure sensors, the CTR algorithm could be implemented at an intersection with high traffic demand and 50–60% MPR. The findings of this study are expected to contribute to the field implementation of the CTR algorithm to improve the traffic network performance. Copyright © 2017 John Wiley & Sons, Ltd.     

Pedestrian crossing detection based on evidential fusion of video-sensors

This paper introduces an online pedestrian crossing detection system that uses pre-existing traffic-oriented video-sensors which, at regular intervals, provide coarse spatial measurements on areas along a crosswalk. Pedestrian crossing detection is based on the recognition of occupancy patterns induced by pedestrians when they move on the crosswalk. In order to improve the ability of non-dedicated sensors to detect pedestrians, we introduce an evidential-based data fusion process that exploits redundant information coming from one or two sensors: intra-sensor fusion uses spatiotemporal characteristics of the measurements and inter-sensor fusion uses redundancy between the two sensors. As part of the EU funded TRACKSS project on cooperative advanced sensors for road traffic applications, real data have been collected on an urban intersection equipped with two cameras. The results obtained show that the data fusion process enhances the quality of occupancy patterns obtained and leads to high detection rates of pedestrian crossings with multi-purpose sensors in operational conditions, especially when a secondary sensor is available.     

Overview and analysis of Vehicle Automation and Communication Systems from a motorway traffic management perspective

During the last decade, there has been an enormous interdisciplinary effort by the automobile industry and numerous research institutions worldwide towards the development, testing and employment of a variety of Vehicle Automation and Communication Systems (VACS) with the main aims to improve road safety and driver convenience. Some VACS, however, have a direct impact on road efficiency as well and could therefore be exploited to relieve road networks from the significant congestion problems and their negative consequences for travel times, safety, fuel consumption, the environment and the quality of life in general. In other words, some of the available VACS could also be used as novel or innovative sensors, actuators and tools towards a new era of traffic management. This paper provides an overview of proposed and available VACS and discusses their perspectives from the motorway traffic management point of view. Classifications of the different systems in this respect are also provided, while SWOT (Strengths–Weaknesses–Opportunities–Threats) analyses are used to identify specific exploitation ways. Current trends and future perspectives of VACS within a motorway traffic management context are finally summarised.     

Evaluating effects of traffic and vehicle characteristics on vehicular emissions near traffic intersections

Urban air quality is generally poor at traffic intersections due to variations in vehicles’ speeds as they approach and leave. This paper examines the effect of traffic, vehicle and road characteristics on vehicular emissions with a view to understand a link between emissions and the most likely influencing and measurable characteristics. It demonstrates the relationships of traffic, vehicle and intersection characteristics with vehicular exhaust emissions and reviews the traffic flow and emission models. Most studies have found that vehicular exhaust emissions near traffic intersections are largely dependent on fleet speed, deceleration speed, queuing time in idle mode with a red signal time, acceleration speed, queue length, traffic-flow rate and ambient conditions. The vehicular composition also affects emissions. These parameters can be quantified and incorporated into the emission models. There is no validated methodology to quantify some non-measurable parameters such as driving behaviour, pedestrian activity, and road conditions     

Information metrics for improved traffic model fidelity through sensitivity analysis and data assimilation

We develop theoretical and computational tools which can appraise traffic flow models and optimize their performance against current time-series traffic data and prevailing conditions. The proposed methodology perturbs the parameter space and undertakes path-wise analysis of the resulting time series. Most importantly the approach is valid even under non-equilibrium conditions and is based on procuring path-space (time-series) information. More generally we propose a mathematical methodology which quantifies traffic information loss.In particular the method undertakes sensitivity analysis on available traffic data and optimizes the traffic flow model based on two information theoretic tools which we develop. One of them, the relative entropy rate, can adjust and optimize model parameter values in order to reduce the information loss. More precisely, we use the relative entropy rate as an information metric between time-series data and parameterized stochastic dynamics describing a microscopic traffic model. On the other hand, the path-space Fisher Information Matrix, (pFIM) reduces model complexity and can even be used to control fidelity. This is achieved by eliminating unimportant model parameters or their combinations. This results in easier regression of parametric models with a smaller number of parameters.The method reconstructs the Markov Chain and emulates the traffic dynamics through Monte Carlo simulations. We use the microscopic interaction model from Sopasakis and Katsoulakis (2006) as a representative traffic flow model to illustrate this parameterization methodology. During the comparisons we use both synthetic and real, rush-hour, traffic data from highway US-101 in Los Angeles, California.     

Field tests of a dynamic green driving strategy based on inter-vehicle communication

This paper presents the design and results for field tests regarding the environmental benefits in stop-and-go traffic of an algorithmic green driving strategy based on inter-vehicle communication (IVC), which was proposed in Yang and Jin (2014). The green driving strategy dynamically calculates advisory speed limits for vehicles equipped with IVC devices so as to smooth their speed profiles and reduce their emissions and fuel consumption. For the field tests, we develop a smartphone-based IVC system, in which vehicles’ speeds and locations are collected by GPS and accelerometer sensors embedded in smartphones, and communications among vehicles are enabled by specially designed smartphone applications, a central server, and 4G cellular networks. Six field tests are carried out on an uninterrupted ring road under slow or fast stop-and-go traffic conditions. We compare the performances of three alternatives: no green driving, heuristic green driving, and the IVC-based algorithmic green driving. Results show that heuristic green driving has better smoothing and environmental effects than no green driving, but the IVC-based algorithmic green driving outperforms both. In the future, we are interested in field tests under more realistic traffic conditions.     

Probe vehicle-based traffic state estimation method with spacing information and conservation law

This paper proposes a method of estimating a traffic state based on probe vehicle data that contain spacing and position of probe vehicles. The probe vehicles were assumed to observe spacing by utilizing an advanced driver assistance system, that has been implemented in practice and is expected to spread in the near future. The proposed method relies on the conservation law of the traffic flow but is independent of a fundamental diagram. The conservation law is utilized for reasonable aggregation of the spacing data to acquire the traffic state, i.e., a flow, density and speed. Its independence from a fundamental diagram means that the proposed method does not require predetermined nor exogenous assumptions with regard to the traffic flow model parameters. The proposed method was validated through a simulation experiment under ideal conditions and a field experiment conducted under actual traffic conditions; and empirical characteristics of the proposed method were investigated.     

Mixed manual/semi-automated traffic: a macroscopic analysis

The use of advanced technologies and intelligence in vehicles and infrastructure could make the current highway transportation system much more efficient. Semi-automated vehicles with the capability of automatically following a vehicle in front as long as it is in the same lane and in the vicinity of the forward looking ranging sensor are expected to be deployed in the near future. Their penetration into the current manual traffic will give rise to mixed manual/semi-automated traffic. In this paper, we analyze the fundamental flow–density curve for mixed traffic using flow–density curves for 100% manual and 100% semi-automated traffic. Assuming that semi-automated vehicles use a time headway smaller than today’s manual traffic average due to the use of sensors and actuators, we have shown using the flow–density diagram that the traffic flow rate will increase in mixed traffic. We have also shown that the flow–density curve for mixed traffic is restricted between the flow–density curves for 100% manual and 100% semi-automated traffic. We have presented in a graphical way that the presence of semi-automated vehicles in mixed traffic propagates a shock wave faster than in manual traffic. We have demonstrated that the presence of semi-automated vehicles does not change the total travel time of vehicles in mixed traffic. Though we observed that with 50% semi-automated vehicles a vehicle travels 10.6% more distance than a vehicle in manual traffic for the same time horizon and starting at approximately the same position, this increase is marginal and is within the modeling error. Lastly, we have shown that when shock waves on the highway produce stop-and-go traffic, the average delay experienced by vehicles at standstill is lower in mixed traffic than in manual traffic, while the average number of vehicles at standstill remains unchanged.     

Probe data-driven travel time forecasting for urban expressways by matching similar spatiotemporal traffic patterns

Travel time is an effective measure of roadway traffic conditions. The provision of accurate travel time information enables travelers to make smart decisions about departure time, route choice and congestion avoidance. Based on a vast amount of probe vehicle data, this study proposes a simple but efficient pattern-matching method for travel time forecasting. Unlike previous approaches that directly employ travel time as the input variable, the proposed approach resorts to matching large-scale spatiotemporal traffic patterns for multi-step travel time forecasting. Specifically, the Gray-Level Co-occurrence Matrix (GLCM) is first employed to extract spatiotemporal traffic features. The Normalized Squared Differences (NSD) between the GLCMs of current and historical datasets serve as a basis for distance measurements of similar traffic patterns. Then, a screening process with a time constraint window is implemented for the selection of the best-matched candidates. Finally, future travel times are forecasted as a negative exponential weighted combination of each candidate’s experienced travel time for a given departure. The proposed approach is tested on Ring 2, which is a 32km urban expressway in Beijing, China. The intermediate procedures of the methodology are visualized by providing an in-depth quantitative analysis on the speed pattern matching and examples of matched speed contour plots. The prediction results confirm the desirable performance of the proposed approach and its robustness and effectiveness in various traffic conditions.     

A methodology for classification by priority for action: Selecting road stretches for network noise action plans

Road traffic noise is an element of outstanding importance within the overall context of environmental impact. This problem must be technically addressed from an efficient viewpoint, and solutions or alternatives should be considered by means of appropriate and consolidated procedures.Up to now, there is no regulated guideline for establishing well-founded priorities when dealing with the diverse road stretches included in the corresponding Action Plans against noise under the Environmental Noise Directive (2002/49/EC). To this end, the present study proposes a methodology to sort, by priority, road stretches identified by their noise problems and therefore requiring appropriate action. The methodology is based on the so-called “road stretch priority index” (henceforth referred to as RSPI). This index involves a number of variables (called “road stretch priority variables”) that are weighted according to their influence on the road traffic noise problem. Thus, the RSPI makes it possible to prioritize different stretches of the Action Plan. To illustrate the application of the proposed methodology, this paper also describes a real case entailing a difficult choice, applying the proposed methodology to a review of the Action Plan against Noise 2008–2012 in the province of Almería, for the road network of the regional government of Andalusia, Spain.     

Atmospheric dispersion modeling near a roadway under calm meteorological conditions

Atmospheric pollutant dispersion near sources is typically simulated by Gaussian models because of their efficient compromise between reasonable accuracy and manageable computational time. However, the standard Gaussian dispersion formula applies downwind of a source under advective conditions with a well-defined wind direction and cannot calculate air pollutant concentrations under calm conditions with fluctuating wind direction and/or upwind of the emission source. Attempts have been made to address atmospheric dispersion under such conditions. This work evaluates the performance of standard and modified Gaussian plume models using measurements of NO₂, PM₁₀, PM_2.5, five inorganic ions and seven metals conducted near a freeway in Grenoble, France, during 11–27 September 2011. The formulation for calm conditions significantly improves model performance. However, it appears that atmospheric dispersion due to vehicle-induced turbulence is still underestimated. Furthermore, model performance is poor for particulate species unless road dust resuspension by traffic is explicitly taken into account.     

Phase transition model of non-stationary traffic flow: Definition,properties and solution method

We consider the problem of modeling traffic phenomena at a macroscopic level. Increasing availability of streaming probe data allowing the observation of non-stationary traffic motivates the development of models capable of leveraging this information. We propose a phase transition model of non-stationary traffic in conservation form, capable of propagating joint measurements from fixed and mobile sensors, to model complex traffic phenomena such as hysteresis and phantom jams, and to account for forward propagation of information in congested traffic. The model is shown to reduce to the Lighthill–Whitham–Richards model within each traffic phase for the case of stationary states, and to have a physical mesoscopic interpretation in terms of drivers’ behavior. A corresponding discrete formulation appropriate for practical implementation is shown to provide accurate numerical solution to the proposed model. The performance of the model introduced is assessed on benchmark cases and on experimental vehicle trajectories from the NGSIM datasets.     

Identifying the onset of congestion rapidly with existing traffic detectors

From an operations standpoint the most important function of a traffic surveillance system is determining reliably whether the facility is free flowing or congested. The second most important function is responding rapidly when the facility becomes congested. These functions are complicated by the fact that conventional vehicle detectors are only capable of monitoring discrete points along the roadway while incidents may occur at any location on the facility. The point detectors are typically placed at least one-third of a mile apart and conditions between the detectors must be inferred from the local measurements.This paper presents a new approach for traffic surveillance that addresses these issues. It uses existing dual loop detector stations to match vehicle measurements between stations and monitor the entire roadway. Rather than expending a considerable effort to detect congested conditions, the research employs a relatively simple strategy to look for free flow traffic. Whenever a unique vehicle passes the downstream station, the algorithm looks to see if a similar vehicle passed the upstream station within a time window that is bounded by feasible travel times. The approach provides vehicle reidentification and travel time measurement on freeways during free flow and through the onset of congestion. If desired, other algorithms can be used with the same detectors to provide similar measurements during congested conditions. The work should prove beneficial for traffic management and traveler information applications, while promising to be deployable in the short term.     

Formal scientific research of traffic collision data utilizing GIS

This paper explores the tenuous link between speeding behavior and accident causation, one that has not been well established in the international literature to date. Taking advantage of established engineering conventions and formulae, we were able to set up an a priori hypothesis suitable for testing. Utilizing this formal scientific method (which GIS researchers have been criticised for not using) we establish a statistical link for this relationship. Our methodology can be used to support all police intervention strategies, including the controversial photo radar systems. The results from our research have been entered into a GIS in order to create a map for spatial display. This map illustrates the relative probability or risk of collision occurrence resulting from speeding at all intersections and interchanges within the scope of the study. It is suggested that this methodology could easily be maintained with periodic updates of data, thus creating a dynamic model from which to monitor traffic safety within the city. Furthermore, this model can be utilized to study specific strategies, allowing for the scrutiny of before, during and after effects. The study area is the entire city of Calgary, Alberta, Canada, and includes all traffic collisions occurring during the year of 1994.     

Identification of vehicle sensor locations for link-based network traffic applications

Information on link flows in a vehicular traffic network is critical for developing long-term planning and/or short-term operational management strategies. In the literature, most studies to develop such strategies typically assume the availability of measured link traffic information on all network links, either through manual survey or advanced traffic sensor technologies. In practical applications, the assumption of installed sensors on all links is generally unrealistic due to budgetary constraints. It motivates the need to estimate flows on all links of a traffic network based on the measurement of link flows on a subset of links with suitably equipped sensors. This study, addressed from a budgetary planning perspective, seeks to identify the smallest subset of links in a network on which to locate sensors that enables the accurate estimation of traffic flows on all links of the network under steady-state conditions. Here, steady-state implies that the path flows are static. A “basis link” method is proposed to determine the locations of vehicle sensors, by using the link-path incidence matrix to express the network structure and then identifying its “basis” in a matrix algebra context. The theoretical background and mathematical properties of the proposed method are elaborated. The approach is useful for deploying long-term planning and link-based applications in traffic networks.     

Estimating traffic volumes for signalized intersections using connected vehicle data

Recently connected vehicle (CV) technology has received significant attention thanks to active pilot deployments supported by the US Department of Transportation (USDOT). At signalized intersections, CVs may serve as mobile sensors, providing opportunities of reducing dependencies on conventional vehicle detectors for signal operation. However, most of the existing studies mainly focus on scenarios that penetration rates of CVs reach certain level, e.g., 25%, which may not be feasible in the near future. How to utilize data from a small number of CVs to improve traffic signal operation remains an open question. In this work, we develop an approach to estimate traffic volume, a key input to many signal optimization algorithms, using GPS trajectory data from CV or navigation devices under low market penetration rates. To estimate traffic volumes, we model vehicle arrivals at signalized intersections as a time-dependent Poisson process, which can account for signal coordination. The estimation problem is formulated as a maximum likelihood problem given multiple observed trajectories from CVs approaching to the intersection. An expectation maximization (EM) procedure is derived to solve the estimation problem. Two case studies were conducted to validate our estimation algorithm. One uses the CV data from the Safety Pilot Model Deployment (SPMD) project, in which around 2800 CVs were deployed in the City of Ann Arbor, MI. The other uses vehicle trajectory data from users of a commercial navigation service in China. Mean absolute percentage error (MAPE) of the estimation is found to be 9–12%, based on benchmark data manually collected and data from loop detectors. Considering the existing scale of CV deployments, the proposed approach could be of significant help to traffic management agencies for evaluating and operating traffic signals, paving the way of using CVs for detector-free signal operation in the future.     

Experienced travel time prediction for congested freeways

Travel time is an important performance measure for transportation systems, and dissemination of travel time information can help travelers make reliable travel decisions such as route choice or departure time. Since the traffic data collected in real time reflects the past or current conditions on the roadway, a predictive travel time methodology should be used to obtain the information to be disseminated. However, an important part of the literature either uses instantaneous travel time assumption, and sums the travel time of roadway segments at the starting time of the trip, or uses statistical forecasting algorithms to predict the future travel time. This study benefits from the available traffic flow fundamentals (e.g. shockwave analysis and bottleneck identification), and makes use of both historical and real time traffic information to provide travel time prediction. The methodological framework of this approach sequentially includes a bottleneck identification algorithm, clustering of traffic data in traffic regimes with similar characteristics, development of stochastic congestion maps for clustered data and an online congestion search algorithm, which combines historical data analysis and real-time data to predict experienced travel times at the starting time of the trip. The experimental results based on the loop detector data on Californian freeways indicate that the proposed method provides promising travel time predictions under varying traffic conditions.