On the Stability of a Flexible Vehicle Controlled by a Human Pilot

This paper presents a stability analysis of a vehicle flexible in the plane of yawing and being controlled by a human pilot. The vehicle is represented by a two degrees-of-freedom model and the pilot is assumed to respond to the lateral displacement and to the lateral velocity with a time delay. It is shown that in order for the pilot model to exhibit a realistic human operator behavior, driver's gain must be linearly proportional to vehicle velocity and also inversely related to frontal visibility. Moreover, application of the Hurwitz criterion indicated that flexibility of the vehicle frame has a destabilising effect on the lateral stability and reduces the stable domain of operation.     

On the Stability of a Flexible Vehicle Controlled by a Human Pilot

SUMMARY

This paper presents a stability analysis of a vehicle flexible in the plane of yawing and being controlled by a human pilot. The vehicle is represented by a two degrees-of-freedom model and the pilot is assumed to respond to the lateral displacement and to the lateral velocity with a time delay. It is shown that in order for the pilot model to exhibit a realistic human operator behavior, driver's gain must be linearly proportional to vehicle velocity and also inversely related to frontal visibility. Moreover, application of the Hurwitz criterion indicated that flexibility of the vehicle frame has a destabilising effect on the lateral stability and reduces the stable domain of operation.     

On the wobble mode of a bicycle

Wheel shimmy and wobble are well-known dynamic phenomena at automobiles, aeroplanes and motorcycles. In particular, wobble at the motorcycle is an (unstable) eigenmode with oscillations of the wheel about the steering axis, and it is no surprise that unstable bicycle wobble is perceived unpleasant or may be dangerous, if not controlled by the rider in time. Basic research on wobble at motorcycles within the last decades has revealed a better understanding of the sudden onset of wobble, and the complex relations between parameters affecting wobble have been identified. These fundamental findings have been transferred to bicycles. As mass distribution and inertial properties, rider influence and lateral compliances of tyre and frame differ at bicycle and motorcycle, models to represent wobble at motorcycles have to prove themselves, when applied to bicycles. For that purpose numerical results are compared with measurements from test runs, and parametric influences on the stability of the wobble mode at bicycles have been evolved. All numerical analysis and measurements are based on a specific test bicycle equipped with steering angle sensor, wheel-speed sensor, global positioning system (GPS) 3-axis accelerometer, and 3-axis angular velocity gyroscopic sensor.     

某重型混合动力垃圾车方案设计

本文以某传统6X4型柴油重卡为原型,根据国内混合动力商用车发展现状,经过合理匹配计算,设计一款混合动力6X4型垃圾车.     

Development of a semi-empirical program for predicting the braking performance of a passenger vehicle

Since the invention of automobiles, the need to know the braking performance of vehicles has been acknowledged. However, because there are numerous design variables as well as nonlinearities in the braking system, it is difficult to predict the performance accurately. In this paper, a computational program is developed to estimate the braking performance numerically. This synthetic braking performance program accounts for pedal force, pedal travel and deceleration of braking parts, such as master cylinder, booster, valve, brake pad, rotor, and hoses. To improve the accuracy of program, a semi-empirical model of a braking system is introduced by using the empirical test data of pad compression, hose expansion and the friction coefficient between the pad and rotor. The accuracy of the estimation is evaluated by comparing it to the actual vehicle test results. The developed program is easy for the brake system engineers to manipulate and it can be used in the development of new vehicles by incorporating the graphical presentations.     

Parametric study of the main parameters influencing the catalytic efficiency of a diesel oxidation catalyst: Parameters influencing the efficiency of a diesel catalyst

This work studies the impact of five parameters: CO and HC engine-out emissions, space velocity, average value and profile of exhaust temperature, on Diesel CO and HC tail-pipe emissions. The first part of this work is conducted on a reactor and shows that both HC and CO light-off temperature increases with CO and HC input concentration. CO and HC initial concentration influence the adsorption/desorption capacities of HC only at high temperatures. Space velocity also influences CO and HC conversion efficiency. The second part of this work studies the impact of different combinations of HC and CO engine-out emissions on CO and HC conversion and tail-pipe emissions in the case of New European Driving Cycle. This part proposes that a Diesel oxidation catalyst must be mainly studied at the Urban Part of NEDC, as the CO and HC conversions are very high at the extra-urban part of NEDC. CO and HC conversion efficiencies are also dependent on exhaust temperature and catalytic volume. In the case of two different profiles of exhaust temperature with the same average temperature, CO and HC conversion efficiency is lower in the case of the smoother profile.     

Prediction of the cooling factors of a vehicle brake disc and its influence on the results of a thermal numerical simulation

In the process of developing the brake disc, it is necessary that we predict the suitability of the design. In this manner, we can affirm that even the first prototype will satisfy all of the customer homologation requests. Usually those comprise different sequential braking tests in which the maximal achieved temperature is the criterion that governs brake disc suitability. The knowledge of how to predict the behavior of a brake disc in the early pretesting phase has a significant impact on development costs and time. The common method that is used for predicting the temperatures in the brake disc during braking is numerical simulation analysis. With the help of Computational Fluid Dynamics, the flow through a vehicle ventilated brake disc of known geometry was determined, and the wall heat transfer coefficients for all vehicle speeds and brake disc temperatures were calculated. The results were then imported into a thermal numerical simulation of a sequential-braking vehicle test. The results showed that the consideration of cooling factors has a significant impact on temperature courses. To obtain accurate results from the numerical simulation and to simulate the vehicle test precisely, the proper wall heat transfer coefficients must be considered. The proposed method produces more accurate numerical results and enables the development engineer to develop suitable brake disc geometry in the early pretesting phase.     

Experimental study of the flow induced by a vehicle fan and the effect of engine blockage in a simplified model

Fans are often tested without downstream blockage and, thus, the performance is considerably different when the fan is mounted in a vehicle as part of a cooling system and where high blockage effect is present downstream. The aim of the present work is to analyze by laser Doppler velocimetry LDV measurements the topology of the flow induced by a fan incorporated in a simplified underhood model reproducing engine blockage and to study the blockage effect of the engine positioning on the flow induced by the fan. The distance between the fan and the engine block affects the mean flow axial velocity U. The vertical velocity component W is greatly influenced by the variation of the distance between the fan and the engine block, both in magnitude and topology.     

On the equivalent wheelbase of a three-axle vehicle

The steady-state handling properties of a rigid vehicle with a tandem rear axle configuration are developed. This work uses conventions resulting in a parsimonious characterisation of steady-state handling of such three-axle vehicles that is shown to be a simple extension of the well-known two-axle bicycle model. Specifically the concepts of understeer and wheelbase are developed for a three-axle vehicle, and shown to play the same role in characterising vehicle handling as they do in the well-known two-axle vehicle model. An equivalent wheelbase of a three-axle vehicle is expressed in terms of vehicle geometry and cornering stiffness of each axle. The model developed in this work is reconciled with previous models that make use of simplifying assumptions found in the literature.     

在大集团旗帜下欲成为"小型巨人"——中国重汽集团济南商用车公司通过ISO/TS 16949认证

2007年8月25日,TUV北德认证(天津)有限公司的认证审核组宣布:中国重汽集团济南商用车有限公司通过ISO/TS 16949质量管理体系现场认证审核。由此,该公司成为国内商用¨     

Computer-Simulation of the Dynamical Curving Behaviour of a Railway-Bogie

This paper describes the modelling of a two axle railway-bogie with variable design configurations and its application in the investigation of the behaviour in transitional and circular curves. Several results indicate possibilities to improve the curving properties and recommend the usage of forced-steering bogies, which show better performance in narrow curves without unbearable sacrifices to high-speed-behaviour on straight track.     

Computer-Simulation of the Dynamical Curving Behaviour of a Railway-Bogie

SUMMARY

This paper describes the modelling of a two axle railway-bogie with variable design configurations and its application in the investigation of the behaviour in transitional and circular curves. Several results indicate possibilities to improve the curving properties and recommend the usage of forced-steering bogies, which show better performance in narrow curves without unbearable sacrifices to high-speed-behaviour on straight track.     

Estimation of the adhesion force for a disc brake in a skid control condition

The performance of brakes has become important due to increased train speeds. The brake system of a train must possess a large brake force to stop the train safely within a limited stopping distance. However, an excessive brake force deteriorates the ride comfort and causes the train to skid. Therefore, it is necessary to control the brake force within the adhesion force limit. This paper presents an analytical method to estimate the relationship between the brake and adhesion forces of a disc brake system. This method has been applied to the actual disc braking control system of the Korea High-Speed Train (HSR350x), and the adhesion force is estimated in an actual skid condition.     

Application of the Pacejka Magic Formula Tyre Model on a Study of a Hydraulic Anti-Lock Braking System for a Light Motorcycle

The object of the study is to apply the Pacejka magic formula tyre model on a study of a hydraulic anti-lock braking system, especially applied to a light motorcycle. A sliding mode PWM controller is designed and tested. Both simulation and experimental studies of an anti-lock braking system are undertaken. The paper presents an analytical approach for estimating the longitudinal adhesive coefficient between a tyre and the road through the magic formula tyre model, the parameters of which are identified by a genetic algorithm. A dynamic analysis of a light motorcycle is carried out in detail. The experimental results show that the antilock braking system designed in the study is effective to prevent wheels locking during emergency braking. The proposed simulation results match experimental data well.     

Application of the Pacejka Magic Formula Tyre Model on a Study of a Hydraulic Anti-Lock Braking System for a Light Motorcycle

The object of the study is to apply the Pacejka magic formula tyre model on a study of a hydraulic anti-lock braking system, especially applied to a light motorcycle. A sliding mode PWM controller is designed and tested. Both simulation and experimental studies of an anti-lock braking system are undertaken. The paper presents an analytical approach for estimating the longitudinal adhesive coefficient between a tyre and the road through the magic formula tyre model, the parameters of which are identified by a genetic algorithm. A dynamic analysis of a light motorcycle is carried out in detail. The experimental results show that the antilock braking system designed in the study is effective to prevent wheels locking during emergency braking. The proposed simulation results match experimental data well.