轮胎泵气噪声有限元仿真分析

轮胎花纹槽泵气噪声是轮胎噪声的主要部分之一。在假设轮胎胎面结构与空气完全耦合的条件下建立轮胎横向花纹槽噪声的有限元模型,在施加与速度相关的强制位移条件下对空气中花纹槽泵气噪声进行仿真仿真,验证轮胎花纹槽泵气噪声的机理,同时通过线性迭加轮胎周向单个横向花纹槽的方法,给出轮胎花纹槽整体噪声的频域曲线。     

带复杂花纹的轮胎滑水显式动力学分析

以205/55R16型半钢子午线轮胎为参考轮胎,利用组合类保角映射簇建模法构建了3种不同胎面花纹的轮胎有限元分析模型.利用该模型进行载荷一下沉量及流体压力一行驶速度分析结果表明.轮胎有限元模型和骨架材料的等效简化方法以及滑水求解策略有效.在此基础上,考察了胎面花纹形态对轮胎滑水性能的影响.结果表明.S型轮胎和V型轮胎由于横向花纹沟的存在,滑水性能优于纵沟胎.     

车辆-模数式伸缩缝耦合振动与冲击荷载分析

为研究导致伸缩缝及其相邻路面损坏的车轮冲击荷载,以桥梁工程中常用的模数式伸缩缝为例,提出一种车辆-桥梁-模数式伸缩缝耦合振动的分析方法。该方法通过分布式弹簧阻尼单元模拟车轮在伸缩缝上的脱空情况;采用等效悬臂或两侧支撑梁模型,考虑脱空段轮胎面的支撑作用,通过车辆-桥梁-伸缩缝耦合振动的迭代算法,实现模数式伸缩缝上的车轮动力荷载的准确模拟,并对载重汽车通过双缝模数式伸缩缝进行实例分析。研究结果表明：①由于伸缩缝结构和车轮位置的变动,很难保证车辆振动的对称性,因此需要采用三维有限元方法分析车轮冲击荷载;②伸缩缝空隙处轮胎面的支撑有助于减小车轮冲击荷载,该支撑刚度与胎面预拉应力密切相关,胎面预拉应力越大,支撑刚度越大,轮载冲击系数越小;③车辆不对称振动导致左右轮冲击系数不同,模数式伸缩缝的中梁跨中冲击系数最大;④模数式伸缩缝上的轮载冲击系数计算值可能超过中国伸缩缝设计指南规定值,该方法可用于确定模数式伸缩缝的最大容许间隙,使车轮冲击荷载小于设计值,以保障伸缩缝的安全服役。     

基于车路系统的事故现场轮胎印迹强度参数化研究

为明确事故现场可视轮胎印迹强度与车辆动力学特性、轮胎橡胶磨损特征及道路表面灰度之间的关联特性,提出基于车路耦合的事故现场轮胎印迹强度参数化研究方法。通过结合动态滑动摩擦因数模型及轮胎非线性模型,建立车辆路面9 DOF非线性系统动力学模型,运用VBOX惯性测量技术验证模型的有效性。运用胎面磨损能量模型,从车路系统角度确定车辆、轮胎和路面特性对轮胎全局摩擦力及胎面磨损特性的影响。结合印迹强度特征模型提出轮胎印迹强度参数研究方法,选取不同制动、转向角工况及3组路面、胎面特性对轮胎路面接地力学特性、胎面橡胶磨损量、可视轮胎印迹特征进行仿真分析。结果表明：印迹强度仅与全局摩擦力大小有关,与轮胎路面滑移方向无关;滑移工况下胎面橡胶磨损量随着全局摩擦力和滑移速度的增大而增大,而印迹强度变化不明显;制动力矩和道路表面灰度对产生可视轮胎印迹起决定作用,转向角主要影响不规则可视轮胎印迹的产生;前轮轮胎最先出现可视印迹,且可视印迹长度和强度均高于后轮轮胎;采取可视印迹起点作为事故车辆速度判定具有一定的误差,应根据具体情况进行具体分析;研究成果能够为基于可视轮胎印迹的交通事故重建提供理论基础。     

一种基于人工智能技术的胎面轮廓优化设计方法

轮胎是一种复杂、多变量的结构体，要想对其进行结构优化是非常困难的。醉庆自有轮胎专用三维有限元分析软件的基础上，结合D－最优试验设计、神经网络和遗传算法进行胎面轮廓的优化，为复杂、多变量的结构优化设计探讨一条效的途径。本文最后给出了相应的算例。结果表明该方法是有效的。     

Numerical method for simulating tire rolling noise by the concept of periodically exciting contact force

For the numerical simulation of tire rolling noise, an important subject is the extraction of normal velocity data of the tire surface that are essential for the acoustic analysis. In the current study, a concept of periodically exciting contact force is introduced to effectively extract the tire normal velocity data. The ground contact pressure within contact patch that is obtained by the static tire contact analysis is periodically applied to the whole tread surface of stationary tire. The periodically exciting contact forces are sequentially applied with a time delay corresponding to the tire rolling speed. The tire vibration is analyzed by the mode superposition in the frequency domain, and the acoustic analysis is performed by commercial BEM code. The proposed method is illustrated through the numerical experiment of 3-D smooth tire model and verified from the comparison with experiment, and furthermore the acoustical responses are investigated to the tire rolling speed.     

轮胎结构有限元分析应用于子午线轮胎帘线受力特性的研究

建立了195／60R14型子午线轮胎三维非线性有限元模型，研究了在静负荷作用下轮胎帘线的受力特征。结果表明，静负荷对轮胎接地区域内帘线受力影响显著；模型带束层结构为2层相交的帘线结构，不能构成力学上的对称；带束层角度的变化对帘线剪应力分布有一定的影响，对胎肩部位帘线剪应力影响较大。     

轮胎胎面与柔性路面摩擦接触的数值分析

应用有限元软件ANASYS建立了包括橡胶胎面和柔性路面结构的有限元模型,探讨了车辆处于自由滚动和紧急制动过程中在不同轮胎／路面界面摩擦系数下的胎面、路表的变形特性和接触应力分布状态。研究结果表明,界面摩擦系数是影响胎面与柔性路面摩擦性能的主要原因,随其值的增加路面弯沉减小,摩擦应力先增加然后保持稳定,但轮胎的磨耗增加,接触压应力增加。适当地丰富路表构造、提高界面摩擦系数能降低路面弯沉,增强紧急制动状态下的抗滑性能;但是当摩擦系数超过某临界值时,随其数值的增大所对应制动状态下的抗滑性能不再提高,且路面压应力明显增加。摩擦特性对路表抗滑性能和路面力学响应的研究提供了一定的理论基础。     

关于汽车轮胎出现锯齿形磨损的分析

分析了汽车轮胎产生锯齿形磨损的主要原因，并对各种花纹轮胎的磨损进行了比较。还介绍对ＢＫ６１４１和ＣＫ６４０型公共汽车车以及装用同一花纹轮胎的公共汽车和载货汽车的轮胎锯齿形磨损情况进行了分析对比。     

基于轮胎-颗粒流动力学模型的避险车道参数匹配方案研究

为了优化山区公路避险车道参数设计方案,基于离散元基本理论与方法,建立轮胎与避险车道集料颗粒流模型。利用自主研发的轮胎性能测试系统对货车轮胎垂直特性进行了室内台架试验研究,通过检测不同输入条件下的响应,标定了轮胎颗粒流模型细观参数。采用漏斗法测量了避险车道集料休止角,结合离散元颗粒流仿真方法,对集料颗粒流模型表面摩擦因数进行了标定。基于所建立的轮胎与避险车道的集料颗粒流模型,仿真分析了轮胎在避险车道中的行驶过程,模拟了车辆在运行过程中的行驶距离、行驶速度与轮胎转速的变化趋势。在甘肃S308省道K209+400处避险车道进行了实车道路试验,试验结果验证了该仿真方法的正确性。通过所建立的轮胎-颗粒流模型对比分析了不同铺设厚度,不同集料大小下的仿真结果。综合考虑减速效果和施工成本,确立了避险车道铺设厚度、铺设长度、颗粒材料等设计技术参数。研究结果表明：离散元法能够很好地模拟车辆在避险车道中的行驶过程;考虑到颗粒固结等因素,建议避险车道铺设厚度不小于0.8 m;针对行驶速度大于90 km·h^-1的载货汽车,避险车道设计长度建议大于130 m;避险车道集料方面,建议选用粒径为1~3 cm且圆度较高的砾石作为路床材料。     

Prediction of tire natural frequency with consideration of the enveloping property

A lumped tire model was developed with consideration of the enveloping property in order to predict the natural tire frequency. Tire stiffness was classified into vertical, sidewall, and enveloping stiffnesses, and the tire characteristics were analyzed in detail experimentally and via finite element analysis. In addition, the effective masses of the tire tread and belt were extracted directly from design specifications taking into account the sizes and material properties of different rubber blocks. Using the design parameters of the tires, natural frequencies were calculated from the derived model and were compared with experimental results. Finally, based on good agreement with experimental results, sensitivity analysis was performed to verify the effect of tire stiffnesses on the natural frequencies.     

汽车啃胎的原因分析及调整方法

对汽车轮胎两侧胎肩、胎冠中央及羽毛状的不正常磨损的啃胎现象进行具体的原因分析及调整方法介绍,也对其它不均匀磨损进行原因分析并且简单介绍各种类型啃胎现象的相应应对措施.     

Recycling technology of tire rubber

Material recycling technology for automotive tire rubber waste was developed by the continuous devulcanization method. The deodorization during the recycling process has become possible by the newly developed method. The devulcanized rubber obtained by these methods from tire rubber waste, generated from both the manufacturing products and scrap tires, shows excellent mechanical properties applicable to the new tire rubber compounds in engineering practice. Furthermore, it was confirmed by actual road tests that a test truck tire containing 10 wt % of the devulcanized rubber in the tread might exhibit tread wear behavior almost equal to that for the standard type with the new rubber compound.     

载重子午轮胎与路面相互作用的分析

根据全钢载重子午线轮胎12.00R20的实际结构,考虑轮胎的几何非线性、材料非线性、接触非线性以及大变形等力学特性,应用有限元的方法建立轮胎的三维模型,橡胶材料采用Yeoh模型,橡胶-帘线复合材料采用加强筋模型,并通过轮胎径向刚度的测试验证了模型的有效性.在数值模拟中分析了轮胎在一定充气压力时,在不同垂直载荷和牵引速度的作用下,与地面在接触区域的变形情况、应力分布、摩擦应力分布等滚动接触规律.结果表明,轮胎与地面接触应力分布存在明显的非均匀性,轮胎的接地面积和地面总反力随着滚动速度的升高而增大.     

虚拟试车场动力学轮胎模型技术研究

以P205/55R16轮胎为对象,建立了虚拟试车场动力学轮胎模型,进行了轮胎径向刚度、扭转特性和侧偏特性的仿真分析。通过与相同工况下的轮胎试验台架测试结果对比可知,所建立的虚拟试车场动力学轮胎模型有效,可以满足虚拟试车场仿真需要。     

高速滚动汽车轮胎稳态温度场分布的数值研究

建立了滚动轮胎热平衡状态下的简化传热数学模型。应用自行开发的传热和热弹性力学分析有限元软件对中型载货车用9．OO一20(12P．R)尼龙斜交胎进行了稳态温度场仿真计算，获得了胎体内部的稳态温度场分布。分析了轮眙的速度、几何结构参数及材料特性参数对轮胎最高温升的影响，通过回归分析建立了该轮胎速度与最高温升的经验计算公式。     

轮胎胎面特性对侧偏模型预测精度影响分析

胎面花纹是影响轮胎性能的重要因素。文中以模态参数模型的稳态侧偏模型为基础，从理论推导和实际计算两方面说明胎而花纹刚度的重要性，其对侧偏模型计算结果的影响要大大高于对垂直模型的影响。因此，在确定轮胎解析模型中胎面花纹参数时应首先考虑其对侧偏模型的影响。     

轮胎非稳态转向特性非线性仿真模型

本文以轮与路面之间的滑移速度为出发点，在稳态指数统一模型的基础上，建立了轮胎非稳态转向特性非线性仿真模型。在实验研究中，发现了动态过程回正力臂和附加的回正力矩的滞后特性。仿真和试验结果对比表明，该模型足以反映轮胎非线性转向特性，可用于前轮及汽车操纵动力学仿真方面的研究。     

Tire wear estimation based on nonlinear lateral dynamic of multi-axle steering vehicle

This paper presents a novel nonlinear dynamic model of a multi-axle steering vehicle to estimate the lateral wear amount of tires. Firstly, a 3DOF nonlinear vehicle dynamic model is developed, including dynamic models of the hydropneumatic suspension, tire, steering system and toe angle. The tire lateral wear model is then built and integrated into the developed vehicle model. Based on the comparison of experimental and simulation results, the nonlinear model is proved to be better than a linear model for the tire wear calculation. In addition, the effects of different initial toe angles on tire wear are analyzed. As simulation results shown, the impact of the dynamic toe angle on the tire wear is significant. The tire wear amount will be much larger than that caused by normal wear if the initial toe angle increases to 1° - 1.5°. The results also suggest that the proposed nonlinear model is of great importance in the design and optimazation of vehicle parameters in order to reduce the tire wear.     

Finite element modeling of static tire enveloping characteristics

To investigate static tire enveloping characteristics, a three dimensional (3-D) finite element model is proposed. The vertical stiffness of the tire is studied on a flat surface with and without cleat. Tire rubber materials and cord layers are represented independently using “rebar” elements available in MSC Marc Mentat. Comparisons of numerical and experimental results are given to show the validity of the proposed model. It is shown that after a certain displacement, the results of the proposed model agree well with experimental results. In addition, the model results show that regardless of the type of the cleat placed under the rim center (hub center), all vertical force curves intersect after a certain displacement, which indicates typical static enveloping characteristics. Moreover, another typical characteristic of the radial tires that is unlike those of bias-ply constructions confirms that the contact patch does not expand laterally after a level vertical load is applied to the tire, which is directly related to fuel consumption and tire tread life.