Development of the World-wide harmonized Light duty Test Cycle (WLTC) and a possible pathway for its introduction in the European legislation

This paper presents the World-wide harmonized Light duty Test Cycle (WLTC), developed under the Working Party on Pollution and Energy (GRPE) and sponsored by the European Union (with Switzerland) and Japan. India, Korea and USA have also actively contributed. The objective was to design the harmonized driving cycle from “real world” driving data in different regions around the world, combined with suitable weighting factors. To this aim, driving data and traffic statistics of light duty vehicles use were collected and analyzed as basic elements to develop the harmonized cycle. The regional driving data and weighting factors were then combined in order to develop a unified database representing the worldwide light duty vehicle driving behavior. From the unified database, short trips were selected and combined to develop a driving cycle as representative as possible of the unified database. Approximately 765,000 km of data were collected, covering a wide range of vehicle categories, road types and driving conditions. The resulting WLTC is an ensemble of three driving cycles adapted to three vehicle categories with different power-to-mass ratio (PMR). It has been designed as a harmonized cycle for the certification of light duty vehicles around the world and, together with the new harmonized test procedures (WLTP), will serve to check the compliance of vehicle pollutant emissions with respect to the applicable emissions limits and to establish the reference vehicle fuel consumption and CO₂ performance.     

Life cycle emissions and cost model for urban light duty vehicles

The growth of vehicle sales and use internationally requires the consumption of significant quantities of energy and materials, and contributes to the deterioration of air-quality and climate conditions. Advanced propulsion systems and electric drive vehicles have substantially different characteristics and impacts. They require life cycle assessments and detailed comparisons with gasoline powered vehicles which, in turn, should lead to critical updates of traditional models and assumptions. For a comprehensive comparison of advanced and traditional light duty vehicles, a model is developed that integrates external costs, including emissions and time losses, with societal and consumer life cycle costs. Life cycle emissions and time losses are converted into costs for seven urban light duty vehicles. The results, which are based on vehicle technology characteristics and transportation impacts on environment, facilitate vehicle comparisons and support policy making in transportation. Substantially, more sustainable urban transportation can be achieved in the short-term by promoting policies that increase vehicle occupancy; in the intermediate-term by increasing the share of hybrid vehicles in the car market and in the long-term by the widespread use of electric vehicles. A sensitivity-analysis of life cost results revealed that vehicle costs change significantly for different geographical areas depending on vehicle taxation, pricing of gasoline, electric power and pollution. Current practices in carbon and air quality pricing favor oil and coal based technologies. However, increasing the cost of electricity from coal and other fossil fuels would increase the variable cost for electric vehicles, and tend to favor the variable cost of hybrid vehicles.     

Options for reducing noise from roads and railway lines

The fundamental noise generation mechanisms of road and rail vehicles are discussed with attention to noise abatement measures. Based on an evaluation of publicly available tire noise data and the European road traffic noise emission model CNOSSOS, it is shown that on the road side there is a significant noise reduction potential in the usage of low-noise tires. From a three months measurement campaign a noise model was derived to predict the maximal sound pressure level of heavy duty vehicles during a pass-by in 7.5 m distance with the parameters vehicle speed and number of axles. With help of recently published information about external costs caused by heavy duty vehicles and the noise prediction tool, a model was developed to derive a money equivalent that can be used as a bonus/malus in a heavy duty vehicle fee. As a measure at the infrastructure, the installation of low-noise pavements is an effective, durable and economically attractive measure. Recent experiences with different technologies from all over the world are compiled and evaluated. On the rail side, an overview of the possible noise reduction strategies is given, followed by a discussion of the current policy and legislation in the EU and on the national level of different European countries.     

Failure rates and data driven policies for vehicle safety inspections in Pennsylvania

Rail, truck, commercial bus, and aircraft have federally mandated safety inspection programs in the United States, while inspections of personal vehicles, which make up the majority of passenger miles, are optionally imposed at the state level. In recent years, some states have chosen to eliminate the vehicle safety inspection program because of budget constraints and concerns about program effectiveness. Currently, 26 states have a schedule for conducting safety inspections, but Pennsylvania is one of thirteen states that currently require all personal light duty vehicles to be inspected every year. The remaining states have completely eliminated safety inspection programs. However, as automobiles become safer, Pennsylvania legislators are now pushing to phase out the inspection program to reduce the costs of owning a vehicle. This study combines Pennsylvania vehicle registration data with two large samples of results from state safety inspections. We find that the state safety inspection fail rate for light-duty vehicles is 12–18%, well above the often-cited rate of 2%. Vehicles that are older than three years old or have more than about 30,000 miles can have much higher rates. When analyzing new vehicles, less than or equal to one year old, it is found that even these vehicles have a failure rate greater than zero. Furthermore, while the vehicle fleet appears to be getting safer over the past few years by improvements in technology or other external circumstances, the inspection failure rate does not appear to be trending toward zero in the near future. We also show that accurate inspection data is limited and often incorrectly analyzed. Lastly, the importance of vehicle maintenance over a vehicle’s lifetime is proven to be evident, since regular usage causes vehicles to deteriorate. We conclude that vehicle safety inspections should continue to be implemented in order to keep driving conditions safe.     

Length-based vehicle classification using event-based loop detector data

Length-based vehicle classification is an important topic in traffic engineering, because estimation of traffic speed from single loop detectors usually requires the knowledge of vehicle length. In this paper, we present an algorithm that can classify vehicles passing by a loop detector into two categories: long vehicles and regular cars. The proposed algorithm takes advantage of event-based loop detector data that contains every vehicle detector actuation and de-actuation “event”, therefore time gaps between consecutive vehicles and detector occupation time for each vehicle can be easily derived. The proposed algorithm is based on an intuitive observation that, for a vehicle platoon, longer vehicles in the platoon will have relatively longer detector occupation time. Therefore, we can identify longer vehicles by examining the changes of occupation time in a vehicle platoon. The method was tested using the event-based data collected from Trunk Highway 55 in Minnesota, which is a high speed arterial corridor controlled by semi-actuated coordinated traffic signals. The result shows that the proposed method can correctly classify most of the vehicles passing by a single loop detector.     

Development of simulated driving cycles for light,medium, and heavy duty trucks: Case of the Toronto Waterfront Area

Driving cycles are an important input for state-of-the-art vehicle emission models. Development of a driving cycle requires second-by-second vehicle speed for a representative set of vehicles. Current standard driving cycles cannot reflect or forecast changes in traffic conditions. This paper introduces a method to develop representative driving cycles using simulated data from a calibrated microscopic traffic simulation model of the Toronto Waterfront Area. The simulation model is calibrated to reflect road counts, link speeds, and accelerations using a multi-objective genetic algorithm. The simulation is validated by comparing simulated vs. observed passenger freeway cycles. The simulation method is applied to develop AM peak hour driving cycles for light, medium and heavy duty trucks. The demonstration reveals differences in speed, acceleration, and driver aggressiveness between driving cycles for different vehicle types. These driving cycles are compared against a range of available driving cycles, showing different traffic conditions and driving behaviors, and suggesting a need for city-specific driving cycles. Emissions from the simulated driving cycles are also compared with EPA’s Heavy Duty Urban Dynamometer Driving Schedule showing higher emission factors for the Toronto Waterfront cycles.     

Driving speeds in Europe for pollutant emissions estimation

The sensitivity of the pollutant emissions as regards the driving speed is demonstrated using emission functions currently available from the literature. An accurate and detailed knowledge of the actual driving speeds is then fundamental for emissions estimations and inventories. However, speed information is often limited and heterogeneous. Through a European synthesis, we examine the various means of investigations: surveys, vehicle instrumentation, traffic modelling, etc.The available statistics provide a high number of reference values for passenger cars and duty vehicles by broad categories and highlight the influence of numerous factors on speed: time period, city size and area, trips origin and destination and vehicle types. Speed estimations and ranges are proposed for the driving in urban areas, on rural roads and on motorways.The significant variations of the speed according to the time of the day, to the areas of a city, and the large dispersion for a given situation raise the question of using single average values. In fact, emissions estimation can be affected by 30% by the quality of the driving speed data.     

Improving estimates of transportation emissions: Modeling hourly truck traffic using period-based car volume data

We estimate hourly truck traffic using period-based car volumes that are usually available from travel demand models. Due to the lack of local or regional data, default vehicle-miles traveled mix by vehicle class in mobile emission inventory models is usually used in transportation emissions inventory estimates. Results from such practice, however, are often far from accurate. Heavy-duty trucks generate orders of magnitudes higher emission rates than light duty vehicles. Vehicle classification data collected from weigh-in-motion stations in California are used to examine the performance of various forms of the method across days of week and geographic areas. We find that the models identified provide satisfactory and statistically robust estimates of truck traffic.     

基于神经网络的无信号路口人车交通行为预测分析

以无信号灯路口人车交通行为为研究对象,对行人和机动车辆在无信号灯路口的整体交通行为进行分类预测。在对路口现场交通情况进行拍摄后,用电脑的分帧技术对所需要的数据进行提取和分类,而后建立BP神经网络模型,确定神经网络的输入变量与输出变量。将样本数据导入神经网络并进行训练和测试后,得出行人和车辆过街类型的分类准确率,并且通过准确率所达到的标准来证明了BP神经网络模型的可行性。     

Impact of horizontal geometric design of two-lane rural roads on vehicle co2 emissions

In 2014, highway vehicles accounted for 72.8% of all Greenhouse Gases emissions from transportation in Europe. In the United States (US), emissions follow a similar trend. Although many initiatives try to mitigate emissions by focusing on traffic operations, little is known about the relationship between emissions and road design. It is feasible that some designs may increase average flow speed and reduce accelerations, consequently minimizing emissions.This study aims to evaluate the impact of road horizontal alignment on CO₂ emissions produced by passenger cars using a new methodology based on naturalistic data collection. Individual continuous speed profiles were collected from actual drivers along eleven two-lane rural road sections that were divided into 29 homogeneous road segments. The CO₂ emission rate for each homogeneous road segment was estimated as the average of CO₂ emission rates of all vehicles driving, estimated by applying the VT-Micro model.The analysis concluded that CO₂ emission rates increase with the Curvature Change Rate. Smooth road segments normally allowed drivers to reach higher speeds and maintain them with fewer accelerations. Additionally, smother segments required less time to cover the same distance, so emissions per length were lower. It was also observed that low mean speeds produce high CO₂ emission rates and they increase even more on roads with high speed dispersions.Based on this data, several regression models were calibrated for different vehicle types to estimate CO₂ emissions on a specific road segment. These results could be used to incorporate sustainability principles to highway geometric design.     

Hierarchical control strategies for energy management of connected hybrid electric vehicles in urban roads

This paper presents a fuel efficient control strategy for a group of connected hybrid electric vehicles (HEVs) in urban road conditions. A hierarchical control architecture is proposed in this paper for every HEV, where the higher level and the lower level controller share information with each other and solve two different problems that aim at improving its fuel efficiency. The higher level controller of each HEV is considered to utilize traffic light information, through vehicle to infrastructure (V2I) communication, and state information of the vehicles in its near neighborhood, via vehicle to vehicle (V2V) communication. Apart from that, the higher level controller of each HEV uses the recuperation information from the lower level controller and provides it the optimal velocity profile by solving its problem in a model predictive control framework. Each lower level controller uses adaptive equivalent consumption minimization strategy (ECMS) for following their velocity profiles, obtained from the higher level controller, in a fuel efficient manner. In this paper, the vehicles are modeled in Autonomie software and the simulation results are provided in the paper that shows the effectiveness of the proposed control architecture.     

Analysis of fuel consumption and pollutant emissions of regulated and alternative driving cycles based on real-world measurements

Discrepancies between real-world use of vehicles and certification cycles are a known issue. This paper presents an analysis of vehicle fuel consumption and pollutant emissions of the European certification cycle (NEDC) and the proposed worldwide harmonized light vehicles test procedure (WLTP) Class 3 cycle using data collected on-road. Sixteen light duty vehicles equipped with different propulsion technologies (spark-ignition engine, compression-ignition engine, parallel hybrid and full hybrid) were monitored using a portable emission measurement system under real-world driving conditions. The on-road data obtained, combined with the Vehicle Specific Power (VSP) methodology, was used to recreate the dynamic conditions of the NEDC and WLTP Class 3 cycle. Individual vehicle certification values of fuel consumption, CO₂, HC and NO_x emissions were compared with test cycle estimates based on road measurements. The fuel consumption calculated from on-road data is, on average, 23.9% and 16.3% higher than certification values for the recreated NEDC and WLTP Class 3 cycle, respectively. Estimated HC emissions are lower in gasoline and hybrid vehicles than certification values. Diesel vehicles present higher estimated NO_x emissions compared to current certification values (322% and 326% higher for NO_x and 244% and 247% higher for HC + NO_x for NEDC and WLTP Class 3 cycle, respectively).     

Extending Time to Collision for probabilistic reasoning in general traffic scenarios

Vehicle-to-vehicle communication systems allow vehicles to share state information with one another to improve safety and efficiency of transportation networks. One of the key applications of such a system is in the prediction and avoidance of collisions between vehicles. If a method to do this is to succeed it must be robust to measurement uncertainty and to loss of communication links. The method should also be general enough that it does not rely on constraints on vehicle motion for the accuracy of its predictions. It should work for all interactions between vehicles and not just a select subset. This paper presents a method to calculate Time to Collision for unconstrained vehicle motion. This metric is gated using a novel technique based on relative vehicle motion that we call “looming”. Finally, these ideas are integrated into a probabilistic framework that accounts for uncertainty in vehicle state and loss of vehicle-to-vehicle communication. Together this work represents a new way of considering vehicle collision estimation. These algorithms are validated on data collected from real world vehicle trials.     

GPS-based optimization of plug-in hybrid electric vehicles’ power demands in a cold weather city

Using the WPG03 duty cycle developed from global positioning data collected in Winnipeg, Canada, real world energy demands and costs are modeled. Three types of plug-in hybrid electric vehicles, four temperatures and two charging scenarios are compared to a vehicle with an internal combustion engine. Cold temperatures are shown to greatly affect vehicle operation energy costs, which is an important consideration for cold weather cities such as Winnipeg. The largest energy cost savings are obtained for smaller-battery plug-in hybrids that had the opportunity to charge during the day.     

Heterogeneous traffic flow modelling for an arterial using grid based approach

A grid based modelling approach akin to cellular automata (CA) is adopted for heterogeneous traffic flow simulation. The road space is divided into a grid of equally sized cells. Moreover, each vehicle type occupies one or more cell as per its size unlike CA traffic flow model where each vehicle is represented by a single cell. Model needs inputs such as vehicle size, its maximum speed, acceleration, deceleration, probability constants, and arrival pattern. The position and speed of the vehicles are assumed to be discrete. The speed of each vehicle changes according to its interactions with other vehicles, following some stochastic rules depending on the circumstances. The model is calibrated and validated using real data and VISSIM. The results indicate that grid based model can reasonably well simulate complex heterogeneous traffic as well as offers higher computational efficiency needed for real time application.     

A discrete–continuous model of households’ vehicle choice and usage, with an application to the effects of residential density

This paper develops a new method to solve multivariate discrete–continuous problems and applies the model to measure the influence of residential density on households’ vehicle fuel efficiency and usage choices. Traditional discrete–continuous modelling of vehicle holding choice and vehicle usage becomes unwieldy with large numbers of vehicles and vehicle categories. I propose a more flexible method of modelling vehicle holdings in terms of number of vehicles in each category, using a Bayesian multivariate ordinal response system. I also combine the multivariate ordered equations with Tobit equations to jointly estimate vehicle type/usage demand in a reduced form, offering a simpler alternative to the traditional discrete/continuous analysis. Using the 2001 National Household Travel Survey data, I find that increasing residential density reduces households’ truck holdings and utilization in a statistically significant but economically insignificant way. The results are broadly consistent with those from a model derived from random utility maximization. The method developed above can be applied to other discrete–continuous problems.     

Origin-destination pattern estimation based on trajectory reconstruction using automatic license plate recognition data

Origin-destination (OD) pattern estimation is a vital step for traffic simulation applications and active urban traffic management. Many methods have been proposed to estimate OD patterns based on different data sources, such as GPS data and automatic license plate recognition (ALPR) data. These data can be used to identify vehicle IDs and estimate their trajectories by matching vehicles identified by different sensors across the network. OD pattern estimation using ALPR data remains a challenge in real-life applications due to the difficulty in reconstructing vehicle trajectories. This paper proposes an offline method for historical OD pattern estimation based on ALPR data. A particle filter is used to estimate the probability of a vehicle’s trajectory from all possible candidate trajectories. The initial particles are generated by searching potential paths in a pre-determined area based on the time geography theory. Then, the path flow estimation process is conducted through dividing the reconstructed complete trajectories of all detected vehicles into multiple trips. Finally, the OD patterns are estimated by adding up the path flows with the same ODs. The proposed method was implemented on a real-world traffic network in Kunshan, China and verified through a calibrated microscopic traffic simulation model. The results show that the MAPEs of the OD estimation are lower than 19%. Further investigation shows that there exists a minimum required ALPR sampling rate (60% in the test network) for accurately estimating the OD patterns. The findings of this study demonstrate the effectiveness of the proposed method in OD pattern estimation.     

An analysis of the effects of French vehicle inspection program and grant for scrappage on household vehicle transaction

The French government has implemented a periodical vehicle inspection program, which aims at maintaining proper functioning of the vehicle and ensuring the emissions control systems installed on the vehicle work properly. Also, an incentive program for scrapping old vehicles was introduced in 1994 through 1996 to promote the replacement of those vehicles with higher emissions by newer vehicles with lower emissions. A hazard-based duration model of household vehicle transaction behavior has been developed in this study to examine the effects of the inspection program and the grant for scrappage on vehicle transaction timing. The model is developed as a competing risks model assuming the following three types of competing risks: replacing one of the vehicles in the household fleet, disposing of one vehicle in the fleet, and acquiring one vehicle to add to the fleet. The empirical analysis is carried out using the panel data of French households' vehicle ownership from 1984 to 1998, obtained by the panel survey called Parc-Auto, which has been conducted by a French marketing firm, SOFRES, since 1976. The long panel observation period facilitates the introduction of macro-economic indicators into the model, enabling the analysis to distinguish the effects of policy measures from macro-economic factors. The empirical results indicate that the expected vehicle holding duration becomes 1.3 years longer under the inspection program than before the program commenced, given that the vehicle is replaced by another vehicle at the end of the holding duration; and that the conditional probability of replacing a vehicle aged 10 years and over becomes 1.2 times higher, and the average holding duration becomes shorter by 3.3 years, when the grant for scrappage is available.     

An integrated model for discrete and continuous decisions with application to vehicle ownership,type and usage choices

This paper proposes an integrated econometric framework for discrete and continuous choice dimensions. The model system is applied to the problem of household vehicle ownership, type and usage. A multinomial probit is used to estimate household vehicle ownership, a multinomial logit is used to estimate the vehicle type (class and vintage) choices, and a regression is used to estimate the vehicle usage decisions. Correlation between the discrete (number of vehicles) and the continuous (total annual miles traveled) parts is captured with a full variance–covariance matrix of the unobserved factors. The model system is estimated using Simulated Log-Likelihood methods on data extracted from the 2009 US National Household Travel Survey and a secondary dataset on vehicle characteristics. Model estimates are applied to evaluate changes in vehicle holding and miles driven, in response to the evolution of social societies, living environment and transportation policies.