Optimal Linear Active Suspensions with Vibration Absorbers and Integral Output Feedback Control

The bandwidth of the body response to a road input in an active suspension may be considerably reduced if the axle motions are independently controlled and if, at the same time, the effects of static and dynamic loads are counteracted by integral action in the body force control system. The paper presents a further application of the Ferguson-Rekasius method, leading to optimal output control with incomplete state feedback. To achieve narrow bandwidth body response the support springs are replaced by hydraulic actuators, and vibration absorbers or active wheel dampers are employed for the control of the axle motions. Active wheel damping is the more effective and gives good results. Proportional-plus-integral control action is shown to reduce the transient body displacements due to external forces.     

Optimal Linear Active Suspensions with Vibration Absorbers and Integral Output Feedback Control

SUMMARY

The bandwidth of the body response to a road input in an active suspension may be considerably reduced if the axle motions are independently controlled and if, at the same time, the effects of static and dynamic loads are counteracted by integral action in the body force control system. The paper presents a further application of the Ferguson-Rekasius method, leading to optimal output control with incomplete state feedback. To achieve narrow bandwidth body response the support springs are replaced by hydraulic actuators, and vibration absorbers or active wheel dampers are employed for the control of the axle motions. Active wheel damping is the more effective and gives good results. Proportional-plus-integral control action is shown to reduce the transient body displacements due to external forces.     

Human body modelling for traffic accident analysis

A traffic accident is a complex phenomenon with vehicles and human beings involved. During a collision, the vehicle occupant is exposed to substantial loads, which can cause the occupant injuries that depend on the level of passive safety, as well as on the occupant's individual characteristics. Correct estimation of injury severity demands a validated human body model and known impact conditions. A human body modelling procedure for the purpose of accident analysis is introduced. The occupant body has been modelled as a multibody system with rigid body segments connected. Geometrical and inertial properties of individual body segments were estimated using computed tomography. Frontal impact conditions were simulated on a sled test facility, while the human body dynamic response was measured. Comparison of experimental data and computer simulation revealed an influence of joint resistive properties on the occupant motion in collisions. The difference between measured and simulated response was minimised using optimisation method. Individualised human body modelling procedure enabled better prediction of the occupant motion during vehicle collision and thus more precise estimation of possible injuries in real-life traffic accidents.     

Investigation of active torsion bar actuator configurations to reduce vehicle body roll

The increasing popularity of sport utility/light-duty vehicles has prompted the investigation of active roll management systems to reduce vehicle body roll. To minimize vehicle body roll and improve passenger comfort, one emerging solution is an active torsion bar control system. The validation of automotive safety systems requires analytical evaluation and laboratory testing prior to implementation on an actual vehicle. In this article, a computer simulation tool and accompanying hardware-in-the-loop test environment are presented for active torsion bar systems to study component configurations and performance limits. The numerical simulation illustrates that the hydraulic cylinder extension limits the active torsion system’s ability to provide body roll angle reduction under various driving conditions. To compare the control system’s time constant and body roll minimization capabilities for different hydraulic valve assemblies and equivalent hose lengths, an experimental test stand was created. For a typical hydraulic pressure and hose diameter, the equivalent hose length was not a key design variable that impacted the system response time. However, the servo-valve offered a quicker transient response and smoother steady-state behavior than the solenoid poppet actuators that may increase occupant safety and comfort.     

一种基于电容传感的乘员感应装置

安全气囊有时会造成不必要的浪费和对儿童的伤害。为解决这一问题，设计了一种新的基于电容传感原理的乘员感应装置，并介绍了电容传感器的构造及微小电容测量的设计。该装置克服了采用超声波原理和质量感应原理系统的不足，能够区分人体，为乘员感应系统的实用化提供了有效手段。静动态试验均证明了系统的可行性。     

Heave-Pitch-Roll Dynamics of Flexible Vehicle in Variable Velocity Run

Analysis for response statistics evaluation of a flexible vehicle travelling with variable velocity over nonhomogeneously profiled flexible track is presented with a heave-pitch-roll model. The vehicle body is idealised as a flexible member with variable cross-section, inertia, damping and stiffness distributions. The vehicle may also have variable section slender elastic attachments. Coupled dynamics with rigid body heave-pitch-roll modes and elastic bending-torsion modes of the vehicle body along with coupled bending-torsion modes of the attachments are considered. Equivalent linear suspension system characteristics are employed for developing the analysis. Numerical results are presented for an aircraft with tricycle landing gear arrangements and comparison is made with other models.     

Heave-Pitch-Roll Dynamics of Flexible Vehicle in Variable Velocity Run

Analysis for response statistics evaluation of a flexible vehicle travelling with variable velocity over nonhomogeneously profiled flexible track is presented with a heave-pitch-roll model. The vehicle body is idealised as a flexible member with variable cross-section, inertia, damping and stiffness distributions. The vehicle may also have variable section slender elastic attachments. Coupled dynamics with rigid body heave-pitch-roll modes and elastic bending-torsion modes of the vehicle body along with coupled bending-torsion modes of the attachments are considered. Equivalent linear suspension system characteristics are employed for developing the analysis. Numerical results are presented for an aircraft with tricycle landing gear arrangements and comparison is made with other models.     

Vertical Vibration Analysis of Vehicle/Imperfect Track Systems

Summary This paper studies the vertical vibration of a vehicle traveling on an imperfect track system. The car body and sleepers are modeled as Timoshenko beams with finite length, and the rail is assumed as an infinite Timoshenko beam with discrete supports. Imperfection of the track system comes from a sleeper lost partial support by the ballast. Since deflection of the rail is limited within a certain interval where the vehicle is passing over, the infinite domain problem can be transformed into a finite domain problem with moving boundary. In this work, the equations of motion of the car body, rail and sleepers are discretized first by the finite element method. The discretized equations of motion for the vehicle and track systems are then assembled, respectively. Finally, the Newmark method is applied to obtain the response of the vehicle and track systems at each time step. The effect of the vehicle speed on the response of the vehicle and track systems is investigated.     

Investigation of active torsion bar actuator configurations to reduce vehicle body roll

The increasing popularity of sport utility/light-duty vehicles has prompted the investigation of active roll management systems to reduce vehicle body roll. To minimize vehicle body roll and improve passenger comfort, one emerging solution is an active torsion bar control system. The validation of automotive safety systems requires analytical evaluation and laboratory testing prior to implementation on an actual vehicle. In this article, a computer simulation tool and accompanying hardware-in-the-loop test environment are presented for active torsion bar systems to study component configurations and performance limits. The numerical simulation illustrates that the hydraulic cylinder extension limits the active torsion system's ability to provide body roll angle reduction under various driving conditions. To compare the control system's time constant and body roll minimization capabilities for different hydraulic valve assemblies and equivalent hose lengths, an experimental test stand was created. For a typical hydraulic pressure and hose diameter, the equivalent hose length was not a key design variable that impacted the system response time. However, the servo-valve offered a quicker transient response and smoother steady-state behavior than the solenoid poppet actuators that may increase occupant safety and comfort.     

基于多体动力学乘员约束系统的模拟研究

为了研究在汽车二次碰撞过程中人体的响应特性,以某车型作为研究对象,运用MADYMO软件进行了乘员约束系统的动力学仿真模拟研究。计算结果与该车型的实车100%覆盖率的刚性固定壁障碰撞(车速为48km/h)试验结果基本一致,验证了模型计算的可行性与正确性。模拟结果表明,假人在整个碰撞过程中的运动均受到较好的控制,其运动主要发生在汽车行进方向;假人自始至终均保持在车舱内,身体所有部位都没有运动到车外;头部与车身内部的坚硬表面也未发生碰撞,该车型具有良好的乘员保护性能。     

Maglev Vehicle/Guideway Vertical Random Response and Ride Quality

Summary The research and development (R & D) of maglev technology had made a great progress in China since the early 1980s. Especially, a 35 km-long Shanghai high-speed maglev railway employing the German Transrapid system began to be constructed on March 1, 2001. Based on the Transrapid system, the paper develops a 10-degree-of-freedom model of maglev vehicle running over three types of guideways with constant speed. Random guideway irregularities are discussed and taken into account for simulation of the vehicle response and for evaluation of the ride comfort. Using the direct time integration method and the discrete fast Fourier transform (DFFT), random responses of the maglev vehicle-guideway systems are obtained and analyzed. Numerical results show that the resonant frequency of car body acceleration response is 0.5–1 Hz, and there is a 2.2 Hz periodic vibration due to the periodic configuration of rigid piers when the maglev vehicle travels over the elevated-beam guideway. The car body acceleration power spectral density (PSD) curves meet well the ride quality criterion of the urban tracked aircushion vehicle (UTACV) and the maximum acceleration of car body is less than 0.05 g. Moreover, the Sperling ride index values are less than 2.5 as long as the operational speed is less than 450 km/h. It is concluded that the maglev vehicle ride quality is quite well.     

Maglev Vehicle/Guideway Vertical Random Response and Ride Quality

Summary The research and development (R & D) of maglev technology had made a great progress in China since the early 1980s. Especially, a 35 km-long Shanghai high-speed maglev railway employing the German Transrapid system began to be constructed on March 1, 2001. Based on the Transrapid system, the paper develops a 10-degree-of-freedom model of maglev vehicle running over three types of guideways with constant speed. Random guideway irregularities are discussed and taken into account for simulation of the vehicle response and for evaluation of the ride comfort. Using the direct time integration method and the discrete fast Fourier transform (DFFT), random responses of the maglev vehicle-guideway systems are obtained and analyzed. Numerical results show that the resonant frequency of car body acceleration response is 0.5-1 Hz, and there is a 2.2 Hz periodic vibration due to the periodic configuration of rigid piers when the maglev vehicle travels over the elevated-beam guideway. The car body acceleration power spectral density (PSD) curves meet well the ride quality criterion of the urban tracked aircushion vehicle (UTACV) and the maximum acceleration of car body is less than 0.05 g. Moreover, the Sperling ride index values are less than 2.5 as long as the operational speed is less than 450 km/h. It is concluded that the maglev vehicle ride quality is quite well.     

Vertical random vibration analysis of vehicle–track coupled system using Green's function method

A vertical vehicle–track coupled dynamic model, consisting of a high-speed train on a continuously supported rail, is established in the frequency-domain. The solution is obtained efficiently by use of the Green's function method, which can determine the vibration response over a wide range of frequency without any limitations due to modal truncation. Moreover, real track irregularity spectra can be used conveniently as input. The effect of the flexibility of both track and car body on the entire vehicle–track coupled dynamic response is investigated. A multi-body model of a vehicle with either rigid or flexible car body is defined running on three kinds of track: a rigid rail, a track stiffness model and a Timoshenko beam model. The results show that neglecting the track flexibility leads to an overestimation of both the contact force and the whole vehicle vibration response. The car body flexibility affects the ride quality of the vehicle and the coupling through the track and can be significant in certain frequency ranges. Finally, the effect of railpad and ballast stiffness on the vehicle–track coupled vibration is analysed, indicating that the stiffness of the railpad has an influence on the system in a higher frequency range than the ballast.     

六速双离合器自动变速器开发

简述了某六速双离合器自动变速器的机械传动系统结构,给出了该变速器最佳动力性换挡策略,并进行了NVH仿真分析.对所开发的液压阀体总成进行的试验表明,该阀体总成的挡位平均响应时间为30.6 ms,比目前国外同类样品响应时间快.介绍了所开发的湿式双离合器结构并进行了双离合器总成试验.结果表明,双离合器1可进行精确地换挡控制;双离合器2虽然能进行换挡,但不易进行精确控制.     

Steady-State Curving Performance of Railway Freight Truck with Damper-Coupled Wheelsets

The focus of this paper is on the steady-state curving behaviour of a freight car system with Damper Coupled Wheelset (DCW), where the wheels of conventional shape within an axle are coupled through a damper element. A freight truck model with two DCW and pseudo-car body on curved track is developed to study the influence of wheelset coupler parameter on the curving response and performance. The response is primarily evaluated in terms of wheelset tracking error and yaw misalignment in response to track curvature and cant deficiency. The curving performance is evaluated in terms of slip and flange boundaries. The results in general, indicate that when the value of coupler parameter is reduced, the wheelset response to track curvature increases, and results in flanging and wheel slip on a less tighter curve than those corresponding to conventional rigid axled wheelsets.     

发动机配气机构刚柔耦合动力学特性研究

基于三维实体模型,运用刚柔耦合理论,把摇臂视为柔性体,采用动态子结构法,建立了某顶置气门发动机配气机构凸轮轴-摇臂-气门系统三维刚柔耦合动力学模型,对其动态特性进行了仿真,得出气门的动力学响应、摇臂动态应力等变化规律.结果表明该发动机配气机构气门升程曲线连续光滑,凸轮与摇臂工作接触过程中无脱离现象发生.     

Steady-State Curving Performance of Railway Freight Truck with Damper-Coupled Wheelsets

SUMMARY

The focus of this paper is on the steady-state curving behaviour of a freight car system with Damper Coupled Wheelset (DCW), where the wheels of conventional shape within an axle are coupled through a damper element. A freight truck model with two DCW and pseudo-car body on curved track is developed to study the influence of wheelset coupler parameter on the curving response and performance. The response is primarily evaluated in terms of wheelset tracking error and yaw misalignment in response to track curvature and cant deficiency. The curving performance is evaluated in terms of slip and flange boundaries. The results in general, indicate that when the value of coupler parameter is reduced, the wheelset response to track curvature increases, and results in flanging and wheel slip on a less tighter curve than those corresponding to conventional rigid axled wheelsets.     

Multi-body elastic simulation of a go-kart: Correlation between frame stiffness and dynamic performance

The elastic response of a vehicle to an applied force determines the dynamic performance, comfort, and support of the vehicle, where the elastic response depends primarily on the stiffness of the frame/chassis. Significant variations in the dynamic response of a vehicle are typically achieved with suitable shock absorbing systems, which contribute significantly to whole body flexibility. The defining feature of a go-kart is the lack of devices capable of absorbing shock and dampening vibration. The tires and body of a go-kart, which consist of a frame of welded beams, must also function as a shock absorption system. The objective of this study was to reproduce the elastic behavior of a commercially available Italian go-kart by modeling the frame in a multibody ADAMS environment and to determine the effect of elastic features on the dynamic performance of the vehicle. Frame stiffness was assessed by applying a static torsion moment, while the circular trajectory of the go-kart was evaluated at different speeds and steering wheel angles. The proposed multibody, flexible model was validated by comparing the static and dynamic response of the go-kart in simulated and experimental analyses. The results of numerical simulations demonstrated that this method may be extended to the design of customized go-kart frames and to the tuning of go-karts for specific racing conditions.     

Roll stabilisation of road vehicles using a variable stiffness suspension system

A variable stiffness architecture is used in the suspension system to counteract the body roll moment, thereby enhancing the roll stability of the vehicle. The variation of stiffness concept uses the ‘reciprocal actuation’ to effectively transfer energy between a vertical traditional strut and a horizontal oscillating control mass, thereby improving the energy dissipation of the overall suspension. The lateral dynamics of the system is developed using a bicycle model. The accompanying roll dynamics are also developed and validated using experimental data. The positions of the left and right control masses are sequentially allocated to reduce the effective body roll and roll rate. Simulation results show that the resulting variable stiffness suspension system has more than 50% improvement in roll response over the traditional constant stiffness counterparts. The simulation scenarios examined is the fishhook manoeuvre.     

两自由度系统的自由振动实验

汽车行驶过程中会因为地面不平引起的冲击载荷、发动机工作的振动等原因而产生振动,当汽车振动的频率与车身固有频率相接近时,车身会产生很大的垂向加速度,不仅会使驾乘人员感到不适,还会造成车身结构的损坏。因此,对于汽车振动模型的研究就显得尤其重要。以搭建的两自由度系统的试验模型为研究对象,求得其在不同初始条件下实验的自由振动响应,来验证理论求解模型的正确性,为汽车平顺性的改善提供理论依据。