Study of n-C<Subscript>12</Subscript>H<Subscript>26</Subscript> reforming over DFC catalyst in a simulated diesel exhaust

In lean-DeNOX catalysis reactions, hydrogen is a good reducing agent in PGM catalysts as well as an effective promoter in selective catalytic reduction reactions over base metal oxide catalysts. However, such a lean-DeNOX system, which uses hydrogen, requires an on-board fuel reforming system applicable to internal combustion engines. In this study, catalytic partial oxidation (CPOx) performance was tested in a laboratory for various reactants and hydrocarbon conditions. Volume concentrations of 5–10% oxygen and 0-5% water vapor were used to simulate diesel exhaust, and n-C₁₂H₂₆ was used as the feedstock for the reforming reaction. In the CPOx of n-C₁₂H₂₆, the highest hydrogen selectivity was 64% and was achieved at 100,000 h-1 GHSV. Additionally, the C/O ratio was less than unity in the absence of water vapor. However, as the water concentration was increased to 2.5 and 5.0 vol. % in the n-C₁₂H₂₆ CPOx reactions, the maximum hydrogen selectivity was increased from 64% in the absence of water to 70% and 75%, respectively. This effect is a consequence of the water-gas shift reaction over the catalyst bed. Regarding oxygen concentration effects, hydrogen selectivity slightly increased with increasing oxygen concentration from 10% to 15%. It was also found that the CPOx reaction of n-C₁₂H₂₆ can be ignited at temperatures below 300 C. Accordingly, it can be concluded that CPOx is a useful and feasible device for promoting diesel DeNOx catalysis in terms of hydrogen productivity and reaction initiation.     

Effect of Hydrothermal Aging over a Commercial DOC on NO<Subscript>2</Subscript> Production and Subsequent SCR Efficiency

In this study, the effect of hydrothermal aging over a commercial diesel oxidation catalyst (DOC) on deterioration in nitrogen dioxide (NO₂) production activity has been experimentally investigated based on a micro-reactor DOC experiment. Through this experimental result, the NO₂ to nitrogen oxides (NOx) ratio at DOC outlet has been mathematically expressed as a function of DOC temperature according to various aging conditions. The current study reveals that the catalyst aging temperature is a more dominant factor than the aging duration in terms of the decrease in NO₂ production performance through DOC. The DOC sample hydrothermally aged for 25 h at 750 °C has displayed the lowest NO₂ to NOx ratio compared to the samples aged for 25 ~ 100 h at 650 °C. Also, in this study, the impact of hydrothermal aging of a DOC on the selective catalytic reduction (SCR) efficiency in a ‘DOC + SCR’ aftertreatment system was predicted by using transient SCR simulations. To validate the SCR simulation, this study has conducted a dynamometer test of a non-road heavy-duty diesel engine with employing a commercial ‘DOC + SCR’ system on the exhaust line. The current study has quantitatively estimated the effect of the variation in NO₂ to NOx ratio due to the hydrothermal aging of DOC on the NOx removal efficiency of SCR.     

O2和 NO2气氛下柴油机炭烟氧化过程及其化学反应动力学参数研究

用热重分析仪对 O2和 NO2气氛下柴油机炭烟的氧化过程进行了试验研究,并利用程序升温氧化（TPO）试验对其化学反应动力学参数进行了研究,建立了 O2和 NO2气氛下柴油机炭烟氧化过程的化学反应动力学模型,并用模型对 O2和 NO2对炭烟的氧化效果进行了对比分析。研究结果表明：柴油机炭烟在 O2气氛下大约从700 K 时开始氧化,氧化反应的活化能为76．8 kJ／mol ,对 O2的反应级数为0．85;而在 NO2气氛下大约从600 K时开始氧化,氧化反应的活化能为21．9 kJ／mol ,对 NO2的反应级数为0．85。在柴油机排气组分条件下,当温度低于750 K 时,NO2氧化炭烟引起的炭烟质量减少占主导;而当温度高于800 K 时,O2氧化炭烟引起的炭烟质量减少占主导。     

Effect of UWS injection at low exhaust gas temperature on NO<Subscript>x</Subscript> removal efficiency of diesel engine

Urea-SCR systems have been widely used in diesel vehicles according to the strengthened NO_x (Nitrogen Oxides) emission standard. The NO_x removal efficiencies of the latest well optimized urea-SCR system are above 90 % at moderate exhaust gas temperature of 250 ~ 450 °C. However, a large amount of NO_x is emitted from diesel vehicles at cold start or urban driving conditions, when the exhaust gas temperature is not high enough for SCR catalyst activation. Although many researchs have been stuied to improve NO_x conversion efficiency at these low temperature conditions, it is still one of important technical issues. In this study, the effect of UWS injection at low exhaust gas temperature conditions is studied. This study uses a 3.4 L diesel engine equipped with a commertial urea SCR system. As a result, it is found that about 5 % of NO_x removal efficiency is improved in the NRTC test when UWS injection starts at the SCR inlet temperature of 150 °C compared to 200 °C. It is also found that urea deposits can be formed on the wall of exhaust pipe, when the local wall temperature is lower than temperature of urea decomposition.     

Heat exchanger/catalytic system for reducing the exhaust emissions from diesel engines

A system has been researched over the past 3 years for reducing the exhaust pollutants from diesel engines for light commercial vehicles. The system researched achieves Euro 6 standards for reduction of polluting gases (CO, HC, PM, NO). It consists of 4 main sections: 1. A heater and heat exchanger (HE); 2. A CO/HC oxidising catalyst (D°C); 3. Pt catalyst on a diesel particulate filter (DPF); 4. A NO reducing reaction (SCR) within the DPF. The system operates as follows. The exhaust gas contains oxidising gases, namely both O₂ and NO₂. The levels of CO and HC are oxidised by O₂ to CO₂ for temperatures above 200°C. Carbon (PM) is oxidised to CO₂ by NO₂ but requires a temperature above 250°C. The operating exhaust temperature of 300°C is ideal for the removal of NO by using the Pt catalyst and the CO generated within the DPF. The heater is required to be able to raise the exhaust temperature at any time to 300°C in order to optimise the performance of the system, since diesel engine exhaust temperatures vary between 160°C (slow speeds) to 350°C (high speeds). Considerable heat is required (??3 kW) to maintain the exhaust gas for a 2l engine at 300°C for engine idle conditions. Therefore a heat exchanger is required to re-circulate the input heat and thereby reduce the maximum power consumption to a maximum of 500W over the engine full operating test cycle. This energy is supplied by the engine battery and alternator. Experimental results have been obtained for the exhaust from a Kubota diesel engine and the reductions in exhaust emissions of 83% (CO/ HC), 58% (NOx) and 99% (PM) were obtained. The PM was continuously cleaned so that there was no build up of back pressure.     

Computational study on the effects of volume ratio of DOC/DPF and catalyst loading on the PM and NOx emission control for heavy-duty diesel engines

The use of a diesel particulate filter (DPF) in a diesel aftertreatment system has proven to be an effective and efficient method for removing particulate matter (PM) in order to meet more stringent emission regulations without hurting engine performance. One of the favorable PM regeneration technologies is the NO₂-assisted regeneration method due to the capability of continuous regeneration of PM under a much lower temperature than that of thermal regeneration. In the present study, the thermal behavior of the monolith during regeneration and the conversion efficiency of NO₂ from NO with an integrated exhaust system of a diesel oxidation catalyst (DOC) and DPF have been predicted by one-channel numerical simulation. The simulation results of the DOC, DPF, and integrated DOC-DPF models are compared with experimental data to verify the accuracy of the present model for the integrated DOC and DPF modeling. The effects of catalyst loading inside the DOC and the volume ratio between the DOC and DPF on the pressure drop, the conversion efficiency, and the oxidation rate of PM, have been numerically investigated. The results indicate that the case of the volume ratio of ‘DOC/DPF=1.5’ within the same diameter of both monoliths produced close to the maximum conversion efficiency and oxidation rate of PM. Under the engine operating condition of 175 kW at 2200 rpm, 100% load with a displacement of 8.1, approximately 55 g/ft³ of catalyst (Pt) loading inside the DOC with the active Pt surface of 5.3 m²/g_pt was enough to maximize the conversion efficiency and oxidation rate of PM.     

Research on exhaust emission control characteristics of a natural gas vehicle — Characteristics of methane oxidation reaction of three-way catalysts

Model gas reaction experiments were conducted to analyze the factors causing the conversion rate of hydrocarbons (consisting mainly of CH₄) to decline in the lean-mixture region, using a natural gas engine fitted with a three-way catalyst. The results showed that there was no decline in the conversion rate of methane in CH₄-O₂ reactions in the lean-mixture region. However, it was observed that oxidation of CH₄ was suppressed when either H₂O or NO was also present. It is thought that prior adsorption of H₂O and NO inhibits adsorption of CH₄ at active sites, resulting in a lower conversion rate.     

Comparison of HC species from diesel combustion modes and characterization of a heat-up doc formulation

This study summarizes engine speed and load effects on HC species emissions from premixed charge compression ignition (PCI) and conventional diesel combustion, and it evaluates diesel oxidation catalyst (DOC) formulations on a gas flow reactor for the purpose of diesel particulate filter regeneration or lean NO_x trap desulfation. HC emissions are sampled simultaneously by a Tedlar bag for light HC species and by a Tenax TA™ adsorption trap for semi-volatile HC species, and they are analyzed by gas chromatography with a flame ionization detector. The bulk temperature and residence time during combustion are key parameters that are important for understanding the effects of speed and load on engine-out HC emissions. The degree of post-flame oxidation is higher in PCI than in conventional combustion, and it is increased for PCI with a higher speed and load, as indicated by a lower fuel alkanes/THC ratio, a higher alkenes/fuel alkanes ratio, and a higher methane/THC ratio. Ethene and n-undecane are two representative HC species, and they are used as a surrogate mixture in the gas flow reactor to simulate PCI and conventional combustion with in-cylinder post fuel injection. Among the three DOC formulations tested, the catalyst with constituent precious metals of platinum and palladium (PtPd) showed the best light-off performance, followed by PtPd with an addition of cerium dioxide (PtPd+CeO₂), and platinum (Pt), regardless of exhaust compositions. Conventional combustion exhaust composition shows a lower light-off temperature than that of PCI, regardless of catalyst formulation.     

Estimation of soot oxidation rate in DPF under carbon and non-carbon based particulate matter accumulated condition

By high particulate matter(PM) reduction performance, diesel particulate filter(DPF) is applied to almost all of modern HSDI diesel engine. PM emitted from diesel engine is consist of carbon based and non-carbon based material. Representative carbon based PM is soot. Non-carbon based PM is produced by wear of engine and exhaust component, combustion of lubrication oil and sulphur in fuel. Accumulation of non-carbon based PM affects pressure difference of DPF and thus accuracy of soot mass estimation in DPF can be lowered during normal and regeneration condition when the pressure difference caused by non-carbon based PM is not recognized correctly. Also unevenly accumulated PM inside of DPF can produce locally different exhaust gas temperature and thus it can lower accuracy of soot mass estimation during regeneration. This study focuses on estimation of soot oxidation rate not by conventional pressure difference but by exhaust gas analysis at up and downstream of DPF. Results, strong correlations between CO₂ -fuel mass ratio and soot oxidation was observed.     

Real-time empirical NO<Subscript>x</Subscript> model based on In-cylinder pressure measurements for light-duty diesel engines

This paper proposes a real-time empirical model of NO_x emissions for diesel engines. The proposed model predicts the level of NO_x emissions using an empirical model developed based on the thermal NO formation mechanism, the extended Zeldovich mechanism. Since it is difficult to consider the exact physical NO formation phenomena in real-time applications, the proposed algorithm adapts the key factors of the NO formation mechanism from the extended Zeldovich mechanism: temperature of the burned gas, concentration of the gas species, and combustion duration where NO is generated. These factors are considered in a prediction model as four parameters: exhaust gas recirculation rate (EGR rate), crank angle location of 50 % of mass fraction burned (MFB50), exhaust lambda value, and combustion acceleration. The proposed prediction model is validated with various steady engine experiments that showed a high linear correlation with the NO_x emission measured by a NO_x sensor. Furthermore, it is also validated for transient experiments.     

微粒氧化催化器与催化型燃油添加剂联合降低重型柴油车微粒排放的试验研究

在低、中、高3种转速及不同扭矩的工况下对重型柴油车进行了PM排放试验,对比了微粒氧化催化器(POC)+柴油机氧化催化剂(DOC)和POC+燃媒催化型燃油添加剂两种PM净化方案。试验研究表明,添加剂最佳添加质量分数为90×10-6,添加剂可替代DOC与POC联合净化PM,并得到较为理想的净化效果。     

Experimental study on the characteristics of nano-particle emissions from a heavy-duty diesel engine using a urea-SCR system

Particulate matter in diesel engine exhaust, particularly nano-particles, can cause serious human health problems including diseases such as lung cancer. Because diesel nano-particle issues are of global concern, regulations on particulate matter emissions specify that not only the weight of particulate matter emitted but also the concentration of nanoparticles must be controlled. This study aimed to determine the effects on nano-particle and PM emissions from a diesel engine when applying a urea-SCR system for NO_x reduction. We found that PM weight increases by approximately 90% when urea is injected in ND-13 mode over the emission without urea injection. Additionally, PM weight increases as the NH₃/NO_x mole ratio is increased at 250 °C. In SEM scans of the collected PM, spherical particles were observed during urea injection, with sizes of approximately 200 nm to 1 μm. This study was designed to determine the conditions under which nano-particles and PM are formed in a urea-SCR system and to relate these conditions to particle size and shape via a quantitative analysis in ND-13 mode.     

Development of new 4-valve/cylinder small DI diesel engine

Nitrous oxide (NO_x) and the particulate matter contained in the exhaust given off by diesel powered vehicles have been identified as elements responsible for polluting the atmosphere. As such, these emissions have been the targets of increasingly strict emission control regulations. Plans are underway to introduce regulations that are even stricter some time early in the next century. The advanced thermal efficiency offered by diesel engines is a feature clearly desired for its potential contribution toward energy conservation and the reduction of global warming. Research and development on the highly thermal-efficient direct-injection diesel engine are progressing at a rapid pace in Europe where introduction of a carbon dioxide tax is under consideration.     

Exhaust emissions and its control methods in compression ignition engines: A review

Extensive usage of automobiles has certain disadvantages and one of them is its negative effect on environment. Carbon dioxide (CO₂), carbon monoxide (CO), hydrocarbons (HC), oxides of nitrogen (NO_x), sulphur dioxide (SO₂) and particulate matter (PM) come out as harmful products during incomplete combustion from internal combustion (IC) engines. As these substances affect human health, regulatory bodies impose increasingly stringent restrictions on the level of emissions coming out from IC engines. This trend suggests the urgent need for the investigation of all aspects relevant to emissions. It is required to modify existing engine technologies and to develop a better after-treatment system to achieve the upcoming emission norms. Diesel engines are generally preferred over gasoline engines due to their undisputed benefit of fuel economy and higher torque output. However, diesel engines produce higher emissions, particularly NO_x and PM. Aftertreatment systems are costly and occupy more space, hence, in-cylinder solutions are preferred in reducing emissions. Exhaust gas recirculation (EGR) technology has been utilized previously to reduce NO_x. Though it is quite successful for small engines, problem persists with large bore engines and with high rate of EGR. EGR helps in reducing NO_x, but increases particulate emissions and fuel consumption. Many in-cylinder solutions such as lower compression ratios, modified injection characteristics, improved air intake system etc. are required along with EGR to accomplish the future emission norms. Modern combustion techniques such as low temperature combustion (LTC), homogeneous charge compression ignition (HCCI), premixed charge compression ignition (PCCI) etc. would be helpful for reducing the exhaust emissions and improving the engine performance. However, controlling of autoignition timing and achieving wider operating range are the major challenges with these techniques. A comprehensive review of diesel engine performance and emission characteristics is given in this paper.     

Numerical study to evaluate the characteristics Of HVAC-related Parameters to reduce CO<Subscript>2</Subscript> concentrations in cars

Today, as people are spending increasing amounts of time in their cars, they have come to recognize that the car should function as a “residential” space. An eco-friendly indoor environment that provides comfort in terms of visual, tactile, and auditory senses is needed for the driver and the passengers. The quality of the car’s indoor environment was evaluated on various factors, such as indoor thermal comfort, indoor air quality, smell, and noise. For the indoor air quality, the typical pollutants that degrade the air quality are CO₂, volatile organic compounds, and exhaust gases. Especially, CO₂ has a direct relationship with drowsy driving which leads to traffic accidents. There have been many experimental and analytical studies to reduce the level of CO₂ in a short time, but analyses of parameters that affect indoor CO₂ concentration are insufficient and comprehensive standards for evaluating the car indoor CO₂ concentration do not yet exist. In this study, several parameters were selected that can influence the reduction rate of CO₂ concentration, and a series of computational analyses were conducted to study the results of these parameters in CO₂ reduction. Based on this study, a prediction equation for CO₂ concentration was derived. For this, a general full factorial design was used to evaluate the CO₂ reduction characteristic based on various parameters (ventilation mode, boarding condition, vent angle, mass flow rate, and operation mode), and then their effects were analyzed to obtain an evaluation database of indoor air quality. From that, a prediction equation was derived to estimate the indoor air quality, enabling us to evaluate the CO₂ concentration quickly that actually influences the human body without carrying out time-consuming CFD analyses for CO₂ concentration. This study will be useful in designing HVAC systems and establishing the control logic for effective improvement of the car’s indoor air quality in the future.     

Carbon Deposit Incineration During Engine Flameout Using Non-Thermal Plasma Injection

In order to investigate the influence of initial regeneration temperatures on diesel particulate filter (DPF) regeneration, an experimental study of DPF regeneration was implemented using a dielectric barrier discharge (DBD) reactor, aided by exhaust waste heat after engine flameout. DPF trapping characteristics and carbon deposit mass were discussed to facilitate further data analysis and calculation. DPF regeneration was then investigated by comparison analysis of deposit removal mass, backpressure drop, and internal temperature change. The results revealed that a large amount of particulate matter (PM) was deposited in DPF with a high filtration efficiency of about 90 %. The deposit removal rate and percentage drop of the backpressure both maximized at the initial temperature of 100 °C. During DPF regeneration, the sharp rise of internal temperature indicated vigorous PM incineration and high CO₂ emission. The results successfully demonstrated DPF regeneration using non-thermal plasma injection during engine flameout, and prominent heat durability was achieved in this method.     

Effect of direct in-cylinder CO2 injection on HCCI combustion and emission characteristics

Fuel injection during negative valve overlap period was used to realize diesel homogeneous charge compression ignition (HCCI) combustion. In order to control the combustion, CO₂ in-cylinder injection was used to simulate external EGR. Effects of CO₂ injection parameters (injection timing, quantity, pressure) on HCCI combustion and emission characteristics were investigated. Experimental results revealed that CO₂ in-cylinder injection can control the start of combustion and effectively reduce NO_x emission. Either advancing CO₂ injection timing or increasing CO₂ injection quantity can reduce peak cylinder pressure and mean gas temperature, delay the starts of low temperature reaction (LTR) and high temperature reaction (HTR), and lower pressure rise rate; NO_x emission was reduced, while smoke, HC, and CO emissions increased. Since the combustion phase was improved, the indicated thermal efficiency was also improved. Injection pressure determines the amount of disturbance introduced into the cylinder. Generally, with the same injection quantity, higher injection pressure results in higher momentum flux and total momentum. Larger momentum flux and momentum has a stronger disturbance to air-fuel mixture, resulting in a more homogeneous mixture; therefore, larger injection pressure leads to lower NO_x and smoke emissions.     

一种基于神经网络的氧化催化器出口温度控制方法

氧化催化器(DOC)出口温度控制是实现颗粒捕集器(DPF)主动再生控制的关键。本文介绍一种基于神经网络的氧化催化器出口温度控制方法,首先结合DOC系统的实际特征以及DOC传热及化学反应特性建立了一阶延迟DOC出口温度模型,然后在温度模型基础上基于神经网络建立了DOC出口温度预测模型,最后将DOC出口温度预测值作为闭环反馈输入建立反馈控制器计算HC喷射量进而控制DOC出口温度。本方法采用整车试验中连续变化工况来验证,试验结果表明DOC出口温度在DPF再生过程中控制在600±20℃范围内,满足DPF精确再生控制要求。     

NOx reduction characteristics of Pt-ZSM-5 catalyst with diesel engine exhaust

The platinum ion-exchanged ZSM-5 zeolite catalyst (Pt-5), which reduces nitrogen oxides (NO_x) in the presence of oxygen and hydrocarbons, was applied to actual diesel engine exhaust. Compared to the Cooper ion-exchanged ZSM-5 zeolite catalyst, the Pt-Z had higher NO_x reduction efficiency, η_NOx = 33%, and lower activation temperature, 250°C, in normal engine operation. It was found that water in the exhaust gas did not apparently affect the NO_x reduction, while the reduction efficiency was significantly affected by the aspect ratio of the catalyst reactor and by the shape of the catalyst, i.e. pellet or honeycomb.     

面向控制的DPF再生效率建模和试验研究

对柴油机颗粒物捕集器(DPF)的再生效率进行实时和准确的在线预估,可为DPF热再生结束的控制提供判断依据,是实现DPF系统化和高效应用的重要功能.本文基于热再生过程中DPF内碳烟颗粒的氧化反应机理探讨并建立了DPF再生效率计算模型,通过发动机台架试验对模型的化学反应动力学参数进行了校核和辨识,从而得到DPF内碳烟颗粒热...