浮动核电站安全壳泄漏率指标分配

[目的]为了探索船用堆安全壳整体和局部泄漏率水平,明确安全壳密封性试验验收准则标准,并开展安全壳周围舱室的气载放射性物质浓度分析。[方法]基于陆上核电站安全壳密封性试验标准,根据"标准分析-提出指标-验证指标"的总体思路,开展浮动核电站泄漏率指标分配、泄漏率计算和可行性分析研究。[结果]结果表明,设计基准事故工况下,浮动核电站安全壳整体泄漏率应控制在3‰/24 h左右,B类和C类贯穿件泄漏率分配分别占整体泄漏率的10%和50%;在试验工况下,安全壳整体泄漏率考虑25%的设计余量。[结论]泄漏率数值分析计算结果满足指标要求,并具有较好的设计余量,对明确安全壳密封性试验验收准则具有重要参考价值。     

一型小水线面双体船的水动力性能与结构设计

简要介绍了中国船舶重工集团公司(CSIS)建立和发展的一种小水线面双体船(SWATH)优化设计工程技术系统.主要包括SWATH船型的概念设计、主尺度与线型优化、有效功率预报、纵向运动稳定性校验及稳定鳍设计、耐波性预报、结构载荷评估、波浪中的船体结构动、静响应分析等有关设计、预报与评估的系统方法.并以一型1500吨级小水线面双体型海洋调查船设计和评估为例对有关设计方法进行了说明和验证,在该船设计中,采用线性和非线性三维水弹性理论来预报载荷与评估在波浪中航行船体的结构安全性,同时在中国船舶科学研究中心(CSSRC)的拖曳水池与耐波性水池中进行了阻力与自航、耐波性与操纵性、波浪载荷等船模拖曳及自航试验.文中还给出了该船有关优化设计及模型试验结果.     

极区船舶冰带构件极限载荷评估

弹性设计准则下,极区船舶通常需要过度的结构加强以确保航行安全。若采用极限载荷设计准则,考虑结构的塑性承载能力,利用一部分屈服点之后的强度储备,则能大大减轻结构重量。本文以中国船舶及海洋工程设计研究院（MARIC）研发的某20000吨级PC5级极地多用途运输船为目标船型,基于IACS URI规范关于冰载荷及相应计算工况的要求,进行了非线性有限元分析。基于计算结果,工程计算推荐100mm×100mm的网格尺寸,材料定义推荐使用理想弹塑性材料。通过对比不同极限载荷准则,认为两倍弹性斜率准则相对更适用于船舶构件。研究成果可为极区船舶结构的设计与强度验证提供参考。     

多用途船集装箱装载工况直接计算分析

多用途船的货舱内装载集装箱的固定形式与普通集装箱船不同,船级社及船舶的设计、建造方对此类船舶结构强度的安全性和可靠性投入更多的关注。为此,参照中国船级社钢质海船入级规范的要求,研究提出了舱内载荷的模拟方法,以某多用途船舱段结构强度有限元计算分析为例,分析研究集装箱横向运动和垂向运动惯性力对船体结构强度的影响。为多用途船装载集装箱工况的结构设计提供准确的分析方法。     

空爆载荷作用下波形夹层板抗爆结构优化设计

为了提高空爆载荷作用下夹层板的抗爆能力,提升其在舰船和海工装备上的应用程度,本文提出了一种针对波形夹层板结构的优化方法,该方法以结构质量和在爆炸载荷作用下的结构应力、变形以及吸能作为评估标准,利用正交试验筛选出样本点,通过BP神经网络生成夹层板结构参数与评估标准间的响应面模型,用遗传算法对响应面模型进行多目标优化分析,得出全局最优解,形成一套夹层板的优化设计方案,这为夹层板抗爆结构优化设计提供了一种新的设计思路和优化方法。     

大型浮式结构物结构碰撞性能分析

碰撞事故是基于事故极限状态设计重点考虑的对象,在设计中越来越受到重视。文章以某大型浮式结构物为研究对象,总结分析ISO、API、HSE、DNV、ABS、BV、LR等标准及规范对碰撞场景的相关规定,提出碰撞分析场景及设计衡准;基于简化分析技术建立碰撞力学模型,利用动态非线性结构分析软件ABAQUS进行仿真分析,通过分析塑性应变、塑性变形、吸能、碰撞力及运动等,校核评估舷侧结构的耐撞性能;分析不同碰撞位置、撞击船型式等对碰撞性能的影响。研究表明:目标大型浮式结构物舷侧结构碰撞事故极限强度满足规范要求,首柱撞击相对比较危险,可作为计算分析控制工况。     

Design of bridges against ship collisions

The paper outlines a rational design procedure for bridge piers and pylons against ship collision impacts. Firstly, a set of risk acceptance criteria are proposed. This is followed by a mathematically based procedure for calculation of the probability of critical ship meeting situations near the bridge, and the probability of ship collision accidents caused by human errors as well as technical errors. This first part of the paper leads to identification of the largest striking ship, “design vessels”, a given bridge pier must withstand without structural failure in order for the bridge connection to fulfil the risk acceptance criteria. The final part of the paper is devoted to an analysis of the needed impact capacity for the bridge pylons and piers exposed to ship bow impact loads from these “design vessels”. For a number of different ship types and different tonnage merchant vessels, load – displacement relations for ship bow collisions against rigid walls are derived. Based on these comprehensive numerical results, a new empirical relation is derived which is suited for design against bow collisions. This expression for maximum bow collision forces is compared with a previously published expression for ice-strengthened ships and with existing standards for assessment of bow crushing forces. It is shown that there is need for an update of these existing standards. For design of piers and pylons against local impact pressure loads, a pressure - area relation for bulbous bow impacts is derived.     

Derivation of plastic framing requirements for polar ships

A new International Association of Classification Societies standard for polar ship design, in the form of a unified requirement is being developed by an international committee with representatives from many classification societies and with the active participation of many polar nations. The framing structural requirements have been developed by a combination of analysis of existing rules and ships, finite element (FE) analysis and analytical solutions of plastic collapse mechanisms. This paper describes the derivation of the 3-hinge and asymmetrical shear plastic collapse mechanisms using work–energy principles. Energy methods are robust and well suited for developing design standards. The results are shown to compare well with non-linear FE analyses of frame strength.     

双平面焊接圆管截面DKT节点的中心撑杆鞍点及冠点位置的应力集中系数(英文)

A set of parametric stress analyses was carried out for two-planar tubular DKT-joints under different axial loading conditions.The analysis results were used to present general remarks on the effects of the geometrical parameters on stress concentration factors(SCFs) at the inner saddle,outer saddle,and crown positions on the central brace.Based on results of finite element(FE) analysis and through nonlinear regression analysis,a new set of SCF parametric equations was established for fatigue design purposes.An assessment study of equations was conducted against the experimental data and original SCF database.The satisfaction of acceptance criteria proposed by the UK Department of Energy(UK DoE) was also checked.Results of parametric study showed that highly remarkable differences exist between the SCF values in a multi-planar DKT-joint and the corresponding SCFs in an equivalent uni-planar KT-joint having the same geometrical properties.It can be clearly concluded from this observation that using the equations proposed for uni-planar KT-connections to compute the SCFs in multi-planar DKT-joints will lead to either considerably under-predicting or over-predicting results.Hence,it is necessary to develop SCF formulae specially designed for multi-planar DKT-joints.Good results of equation assessment according to UK DoE acceptance criteria,high values of correlation coefficients,and the satisfactory agreement between the predictions of the proposed equations and the experimental data guarantee the accuracy of the equations.Therefore,the developed equations can be reliably used for fatigue design of offshore structures.     

安全水平法在SOLAS 救生艇结构强度衡准制定中的应用

本文将安全水平法应用于SOLAS第III章救生艇结构强度衡准的制定。主要采用综合安全评估对救生艇结构强度相关的功能性要求进行衡准的初步制定,从而得出需要的安全水平。基于强度衡准理论分析、实艇试验和事故数据分析相结合的方式评估了现有救生艇结构强度的安全水平,对衡准的合理性提出修改的建议。研究结果为安全水平法在船舶技术标准制定和安全水平评估方面的应用提供了实际案例和使用建议。     

液化气体船独立液舱的疲劳与断裂寿命预测

随着低温、高强度钢和薄板在液化气体船上的广泛应用,使得液舱结构安全性问题愈发严重,传统的强度评估方法已经不能满足产品设计的特殊要求,基于断裂力学的疲劳寿命评估已成为液化气体船结构安全评估的主要手段。本文选取江南造船自主研发的超大型乙烷运输船为研究对象,其独立液舱的舱体采用低温镍钢5Ni材料,可运载温度低至-104℃的乙烯、乙烷和丙烷等货品,需满足IGC CODE,USCG和船级社规范等要求。本文采用BS7910失效评定方法和Pairs裂纹扩展速率计算公式,完成液舱结构初始表面裂纹扩展至贯穿型裂纹,再产生结构断裂失效损坏的寿命预测,为超大型乙烷运输船的自主研发提供一种有效的技术途径。     

MARK III 型LNG模拟舱结构安全评估及优化设计研究

液化天然气（Liquefied Natural Gas）运输船的建造技术复杂，货物维护系统（Cargo Containment System） 种类繁多，船上 LNG 常采用低温高压的储藏方式，该方式对储舱结构强度以及货物维护系统的 变形要求非常高。本文采用有限元方法， 对根据行业规范设计的 MARK III 型 LNG 模拟舱结构进行结构 强度安全性评估，并在满足 LNG 模拟舱结构承载能力要求的基础上，对 MARK III 型 LNG 模拟舱进行结 构优化设计研究，为今后 MARK III 型 LNG 运输船的船体结构设计和优化提供可靠的技术支撑。     

碰撞/搁浅事故中船体强桁材结构损伤机理解析预报方法研究

随着航运业的快速发展,海上航行的船舶越来越多.尽管人们做了许多努力避免海上意外事故的发生,但海难事故依然不可避免.为了降低上述事故造成的损失,需要在设计阶段快速并准确地预报船舶的结构耐撞性.本文以强桁材结构为研究对象,通过开展准静态冲压试验及相应的数值仿真,分析强桁材结构在面内冲压载荷作用下的变形机理,并基于试验与仿真所得到的结构变形特点,提出强桁材面内受压时的变形模式.以此为基础,运用塑性力学理论,推导出结构变形能、瞬时结构变形抗力及平均结构变形抗力的解析预报公式,并将计算结果与试验结果进行比较验证.研究得到的结构面内受压变形能和抗力解析计算公式,可以快速评估事故载荷下结构的响应情况,包括结构变形阻力及能量耗散,具有使用方便,计算速度快,计算结果相对可靠的优点,对船体耐撞结构设计及抗撞性能评估具有一定的指导意义.     

集装箱船的振动与响应评估

按振动分布范围的不同,对集装箱船的振动与响应分析方法进行了分类,讨论了频率储备、激振力、阻尼、附连水质量、振动衡准等问题。并以一艘2750TEU集装箱船为例,进行了整船和局部结构的振动评估,最后对集装箱船的动态设计方法进行了归纳。     

潜艇结构的失效模式及影响分析

在结构系统可靠性分析或系统安全分析中，主要是要对系统的失效模式有较深刻的理解。而FMEA（失效模式及影响分析）方法虽然简单，却很实用，能够透彻地理解系统的安全性要求，同时也为结构系统的风险分析（PRA）打下基础。本文对潜艇结构的失效模式与影响分析作了初步研究。     

海上风电运维船小型化波浪补偿登乘栈桥设计

针对海上风电机组运维需求,设计海上风电运维船的小型化波浪补偿登乘栈桥。进行登乘栈桥的总体设计、力学分析和软件设计,并对登乘栈桥的三维模型进行有限元仿真。仿真结果表明,所进行的设计可满足海上风电运维船的小型化和轻量化要求,保证人员与物料的安全和作业环境的稳定。     

Design method for steel deck plates under quasi-static patch loads with allowable plastic deformations

Plastic deformation of plates in steel deck structures under heavy vehicle or helicopter wheel loads is common in ships and offshore structures, and is therefore of significant interest to designers of ro-ro/cargo ships, helicopter-carrying ships and offshore platforms. To provide insight into the plastic deformation of plates, the nonlinear elasto-plastic response of stiffened steel plates loaded quasi-statically by a central rigid rectangular indenter is investigated both experimentally and numerically. The numerically-determined stiffened plate permanent deflections compare well with those obtained experimentally. The concept of applying the elasto-plastic method to the design of deck plates under wheel patch loads is introduced, and the design principle of wheel patch loaded plating is studied together with the design criteria. A simple design formula to determine plating thickness is proposed based on an acceptable level of permanent set. Ship-mounted helideck plating design cases are given to illustrate the elasto-plastic method, and comparisons are made between the thicknesses derived using the proposed design formula and those found from Lloyd's Register (LR), Bureau Veritas (BV) and DNV-GL rule requirements.     

集装箱船整船有限元结构分析

文章以一艘１７００箱集装箱船为例,阐述了整船有限元结构分析方法。先建立全船有限元模型和质量模型,再用三维流体动力计算程序进行波浪随机载荷的长期预报,并在此基础上导出设计波参数组,最后,在全船有限元模型上 计算得出船体结构在各个设计波上的应力分布和变形结果,所得到的船体结构有限元分析结果对同类型集装箱船的设计和强度分析有一定的参考价值,对其它类型的船舶结构强度分析也有一定的借鉴意义。     

深水定位系统的安全管理(英文)

Based on relevant in-service experience, this paper discusses how risks associated with station-keeping systems can be controlled through adequate design criteria, inspection, repair and maintenance practice, as well as quality assurance and control of the engineering processes. Particular focus must be placed on quantitative design for system robustness. The application of structural reliability analysis to quantify safety is briefly reviewed. In particular it was emphasized that reliability predictions based on normal uncertainties and variability yielded lower failure rates than those experienced for predictions of hulls and catenary mooring systems; gross errors in design, fabrication and operation were responsible. For this reason the broad safety management approach mentioned above was proposed. Moreover, it was found that this approach needed to be supported by a quantitative risk assessment. Finally, the challenges in dealing with the effects of human factors in risk management are outlined, along with means to deal with them in a qualitative manner, by the so-called barrier method to limit risk.     

浮冰冲击作用下的乙烯运输船体 舷侧结构强度分析

对无限航区的21000m3乙烯运输船舷侧结构,分别采用纵骨架式和横骨架式冰区加强设计。根据FSICR规范要求,更新舷侧冰带区域内构件尺寸,并针对艏部冰带区域内船体结构,分别建立了原始的、纵骨架式的和横骨架式的冰带结构设计有限元模型。通过强度计算,认为艏部冰带区新结构满足规范设计载荷要求。在此基础上,单独建立艏货舱冰区舷侧外板板架有限元模型,研究两种新设计形式适用的外板在更大浮冰冲击载荷作用下塑性变形。计算结果表明:纵骨架式结构外板塑性变形明显低于横骨架式。