Unconventional USC intersection corridors: evaluation of potential implementation in Doha,Qatar

Unconventional intersection designs have been recently proposed as a new approach to deal with heavy left turns at signalized intersections. One of these unconventional schemes, the Upstream Signalized Crossover (USC) intersection, was shown to significantly reduce average vehicle delays; particularly when the volumes entering the intersection are relatively high. The Ministry of Public Works of Qatar is considering the implementation of the USC intersection on three signalized intersections along a major urban corridor in Doha. This paper investigates the potential improvements associated with the USC implementation. VISSIM was used to analyze the proposed USC intersections and the existing conventional intersections. Analyses were carried out for AM , Midday, and PM peak hours. The results showed that most of the travel time measurement sections experienced lower delays in the USC configuration for the three peak periods. As well, the total system delay, in hours, for the USC configuration was less than that of the conventional configuration by 19.4, 14.8, and 13.6% for the AM , Midday, and PM peaks, respectively. The average control delay for each single USC intersection was lower than its conventional counterpart by between 7.6 and 22.9%. Copyright © 2010 John Wiley & Sons, Ltd.     

Modeling traffic operation at signalized intersections without explicit left‐turn yielding rules with an enhanced cell transmission model

This paper presents an enhanced cell transmission model (CTM) to capture traffic operation at signalized intersections without explicit permissive left‐turn yielding rules (i.e. aggressive permissive left‐turn maneuvers may not necessarily yield to opposing through traffic), which can be widely observed in many developing countries. Different from previous studies that focus on traffic dynamics on approaching links, this study contributes to modeling traffic operations within the intersection. A novel cell transmission framework with various types of virtual cells is proposed to model the dynamics of traffic movements from approach to exit. The unique phenomenon of competitive occupying of the conflict point between the left turn and opposing through movements is modeled. The cell state indicating its blockage is proposed to capture the dynamic queue formulation and dissipation and to evaluate the operational traffic performance at the intersection. Field validation results show that the proposed model can capture the operation of traffic at signalized intersections without explicit permissive left‐turn yielding rules with significantly higher level of accuracy than traditional traffic flow models. Copyright © 2016 John Wiley & Sons, Ltd.     

Operational analysis of the contraflow left-turn lane design at signalized intersections in China

The primary objective of the study was to evaluate the impacts of an unconventional left-turn treatment called contraflow left-turn lane (CLL) on the operational performance of left-turn movement at signalized intersections. An analytical model was developed for estimating the capacity of left-turn movement at signalized intersections with the CLL design. The capacity model was calibrated and validated using field data collected at six approaches at five signalized intersections in the city of Handan, China. The results of field data analyses showed that the use of CLL design improved the capacity of left-turn movements. However, the capacity gains with the CLL design were quite stochastic considering the randomness in the arrivals of left-turning vehicles. Analytical delay models were proposed for estimating the delay to left-turning vehicles at intersections with the CLL design. A procedure was also proposed for optimizing the location of the upstream median opening and the green interval of the pre-signal. Simulation analyses were conducted to compare the delay experienced by the left-turning and through vehicles at signalized intersections with the conventional left-turn lane, the CLL and another unconventional left-turn treatment entitled “tandem design”. The results showed that both CLL and tandem designs outperformed conventional left-turn lane design; and the CLL design generated less delay to both the left-turning and through vehicles as compared with the tandem design.     

Modeling delay at signalized intersections with channelized right‐turn lanes considering the impact of blockage

This paper presents a probabilistic delay model for signalized intersections with right‐turn channelization lanes considering the possibility of blockage. Right‐turn channelization is used to improve the capacity and to reduce delay at busy intersections with a lot of right‐turns. However, under heavy traffic conditions the through vehicles will likely block the channelization entrance that accrues delay to right‐turn vehicles. If the right‐turn channelization gets blocked frequently, its advantage in reducing the intersection delay is neglected and as a result the channelization lane becomes inefficient and redundant. The Highway Capacity Manual (HCM) neglects the blockage effect, which may be a reason for low efficiency during peak hours. More importantly, using HCM or other standard traffic control methods without considering the blockage effects would lead to underestimation of the delay. To overcome this issue, the authors proposed delay models by taking into account both deterministic and random aspects of vehicles arrival patterns at signalized intersections. The proposed delay model was validated through VISSIM, a microscopic simulation model. The results showed that the proposed model is very precise and accurately estimates the delay. In addition, it was found that the length of short‐lane section and proportion of right‐turn and through traffic significantly influence the approach delay. For operational purposes, the authors provided a step‐by‐step delay calculation process and presented approach delay estimates for different sets of traffic volumes, signal settings, and short‐lane section lengths. The delay estimates would be useful in evaluating adequacy of the current lengths, identifying the options of extending the short‐lane section length, or changing signal timing to reduce the likelihood of blockage. Copyright © 2016 John Wiley & Sons, Ltd.     

Traffic conflict models to evaluate the safety of signalized intersections at the cycle level

The safety of signalized intersections has often been evaluated at an aggregate level relating collisions to annual traffic volume and the geometric characteristics of the intersection. However, for many safety issues, it is essential to understand how changes in traffic parameters and signal control affect safety at the signal cycle level. This paper develops conflict-based safety performance functions (SPFs) for signalized intersections at the signal cycle level. Traffic video-data was recorded for six signalized intersections located in two cities in Canada. A video analysis procedure is proposed to collect rear-end conflicts and various traffic variables at each signal cycle from the recorded videos. The traffic variables include: traffic volume, maximum queue length, shock wave characteristics (e.g. shock wave speed and shock wave area), and the platoon ratio. The SPFs are developed using the generalized linear models (GLM) approach. The results show that all models have good fit and almost all the explanatory variables are statistically significant leading to better prediction of conflict occurrence beyond what can be expected from the traffic volume only. Furthermore, space-time conflict heat maps are developed to investigate the distribution of the traffic conflicts. The heat maps illustrate graphically the association between rear-end conflicts and various traffic parameters. The developed models can give insight about how changes in the signal cycle design affect the safety of signalized intersections. The overall goal is to use the developed models for the real-time optimization of signalized intersection safety by changing the signal design.     

Traffic performance of shared lanes at signalized intersections based on cellular automata modeling

Shared lanes at signalized intersections are designed for use by vehicles of different movement directions. Shared lane usage increases the flexibility of assigning lane grouping to accommodate variable traffic volume by direction. However, a shared lane is not always beneficial as it can at time result in blockage that leads to both capacity and safety constraints. This paper establishes a cellular automata model to simulate traffic movements at signalized intersections with shared lanes. Several simulation experiments are carried out both for a single shared lane and for an approach with a shared lane. Simulation of a single shared lane used by straight‐through and right‐turn (as similar to left‐turn in the USA) vehicles suggests that the largest travel delay occurs when traffic volumes (vehicles/lane) of the two movement streams along the shared lane are at about the same level. For a trial lane‐group with a shared lane, when traffic volumes of the two movement streams are quite different, the shared lane usage is not efficient in terms of reduction in traffic delay. The simulation results are able to produce the threshold traffic volume to arrange a shared lane along an approach. Copyright © 2013 John Wiley & Sons, Ltd.     

A reverse causal-effect modeling approach for signal control of an oversaturated intersection

A novel approach is presented in which signalized intersections are treated as normal highway bottlenecks for improved computational efficiency. It is unique in two ways. First, it treats the signalized intersections as common freeway bottlenecks by a reversed cause and effect modeling approach. Both traffic arrivals and departures are modeled by smooth continuous functions of time as if there were no interruptions to traffic flows from signals. The use of smooth continuous functions for departure curves instead of commonly used step functions makes it easy to apply differential calculus in optimization and future extension to a system of intersections. Second, a dynamic linear programming (LP) model is then developed to maximize the total vehicular output from the intersection during the entire period of congestion subject to prevailing capacity and other operational constraints. The continuous optimal departure flow rate (the effect) is then converted to signal timing parameters (the cause) that can be readily implemented. Two numerical examples are presented to demonstrate the properties of the proposed algorithm and examine its performance.     

A continuous-flow-intersection-lite design and traffic control for oversaturated bottleneck intersections

Oversaturation has become a severe problem for urban intersections, especially the bottleneck intersections that cause queue spillover and network gridlock. Further improvement of oversaturated arterial traffic using traditional mitigation strategies, which aim to improve intersection capacity by merely adjusting signal control parameters, becomes challenging since exiting strategies may (or already) have reached their “theoretical” limits of optimum. Under such circumstance, several novel unconventional intersection designs, including the well-recognized continuous flow intersection (CFI) design, are originated to improve the capacity at bottleneck intersections. However, the requirement of installing extra sub-intersections in a CFI design would increase vehicular stops and, more critically, is unacceptable in tight urban areas with closed spaced intersections. To address these issues, this research proposes a simplified continuous flow intersection (called CFI-Lite) design that is ideal for arterials with short links. It benefits from the CFI concept to enable simultaneous move of left-turn and through traffic at bottleneck intersections, but does not need installation of sub-intersections. Instead, the upstream intersection is utilized to allocate left-turn traffic to the displaced left-turn lane. It is found that the CFI-Lite design performs superiorly to the conventional design and regular CFI design in terms of bottleneck capacity. Pareto capacity improvement for every traffic stream in an arterial system can be achieved under effortless conditions. Case study using data collected at Foothill Blvd in Los Angeles, CA, shows that the new design is beneficial in more than 90% of the 408 studied cycles. The testing also shows that the average improvements of green bandwidths for the synchronized phases are significant.     

Disaggregate safety evaluation for signalized intersections and evaluation tool

This study was to evaluate traffic safety of four‐legged signalized intersections and to develop a spreadsheet tool for identifying high‐risk intersections taking into consideration vehicle movements, left‐turn signal phase types, and times of day. The study used data from Virginia and employed count data models and the empirical Bayes (EB) method for safety evaluation of such intersections. It was found that crash pattern defined by vehicle movements involved in a crash and time of day are important factors for intersection crash analysis. Especially for a safety performance function (SPF), a model specification (Poisson or NB), inclusion of left‐turn signal types, type of traffic flow variables, variable functional forms, and/or magnitudes of coefficients turned out to be different across times of day and crash patterns. The spreadsheet application tool was developed incorporating the developed SPFs and the EB method. As long as Synchro files for signal plans and crash database are maintained, no additional field data collection efforts are required. Adjusting the developed SPFs and the spreadsheet for recent traffic and safety conditions can be done by applying the calibration methods employed in the SafetyAnalyst software and the Highway Safety Manual. Implementing the developed tool equipped with streamlining data entry would greatly improve accuracy and efficiency of safety evaluation of four‐legged signalized intersections in localities and highway agencies that cannot operate the SafetyAnalyst. Copyright © 2010 John Wiley & Sons, Ltd.     

A programmable calculation procedure for number of traffic conflict points at highway intersections

Traffic movement conflict points at intersections are the points at which traffic movements intersect (including crossing, merging, and diverging). Numbers and distribution of different types of conflict points are used to evaluate intersection access management designs and safety performance. Traditionally, the determination of the numbers of conflict points for different traffic movements is based on manual methods, which causes the difficulty for computerized procedures to evaluate safety performance of different access management designs. Sometimes, a programmable calculation procedure may provide more effective solutions as compared with manual methods. This paper presents a programmable calculation procedure for the determination of the numbers of conflict points, which could be used as a basis for a computerized procedure. Concepts of virtual movement lanes and intersection quadrants are introduced to specify types of intersections, traffic lane configurations, and traffic movement regulations. Calculation models, based on such concepts, for traffic movement conflict points at signalized and unsignalized intersections can be obtained. In support of the procedure, case studies are presented in the paper. The procedure presented in the paper can be programmed into a computer program for the purpose of a computerized evaluation of intersection safety and design performance of different access management or control approaches. Copyright © 2012 John Wiley & Sons, Ltd.     

Special provisions for left turns at signalized intersections to increase capacity and safety

Heavy left-turns at intersections are not only difficult to accommodate but also often cause traffic accidents. Such problem can be reduced by adopting an exclusive left-turn signal phase, but in this case the cycle length needs to be extended and the overall intersection capacity reduced. This problem is particularly important in such countries as Korea where unprotected left turns are rarely used. Innovative intersection designs and operational methods for avoiding these problems are presented and their effects of increasing capacity and reducing vehicle delay are analyzed. They rule out the requirement for exclusive left-turn phase while accommodating a large volume of left-turns quite safely.     

Noise level in the vicinity of signalized roundabouts

The analysis, assessment and estimation of noise levels in the vicinity of intersections is a more complex problem than a similar analysis for roads and streets. This is due to the varied geometry of the intersections, differences in the loads of individual movements, participation of heavy vehicles and mass transport vehicles, as well as the various types of traffic management and traffic control. This article analyses the influence of intersection type and traffic characteristics on the noise levels in the vicinity of classic channelized intersections with signalization, roundabouts and signalized roundabouts. Based on the conducted measurements, it has been established that, with comparable traffic parameters and the same distance from the geometric centre of the intersection, the L_Aeq value for signalized roundabouts is 2.5–10.8 dB higher in comparison to classic channelized intersections with signalization and 3.3–6.7 dB higher in relations to the analysed roundabout. Additionally the differences between L_Aeq levels at individual entries at the same signalized roundabouts may reach the value of approximately 4.5 dB. Such situation is influenced by differences in the intersection geometry, diameter of the intersection’s central island, traffic flow type, traffic management at the entries and traffic volume, especially the amount and traffic movements of multiple axle heavy vehicles. These factors have been analysed in detail in relation to signalized roundabouts in this paper.     

Increasing the capacity of signalized intersections by allocating exit lanes to turning movements

Unconventional intersection designs have been used to increase the capacity of intersections that are over‐saturated under conventional ones. However, existing unconventional designs typically require extra land space and their effectiveness often depends on drivers' familiarity with the uncommon operating rules. To overcome these challenges, we propose a new unconventional design, where movements that are mutually incompatible under the conventional design can be made compatible of each other by allocating exit lanes to them appropriately, thereby creating opportunities for capacity improvement. We develop a lane‐based capacity optimization model that incorporates the allocation of exit lanes as decision variables. The model is formulated as a Binary Mixed Integer Linear Programming problem, which can be efficiently solved by standard branch‐and‐bound algorithms. Numerical experiments show that significant capacity improvement can be obtained under our design. Besides proposing a new unconventional design, we also contribute to the literature of lane‐based signal optimization methods by providing a novel linear formulation for the latest, yet nonlinear, model described in Wong and Heydecker [Transportation Research Part B 45(4):667–681]. This improvement is methodologically beneficial as linear models are computationally more convenient than nonlinear ones. Copyright © 2017 John Wiley & Sons, Ltd.     

A probabilistic approach to calculate capacity of signalized intersections with a red light camera

In recent years, red light cameras (RLCs) have been installed at many signalized intersections. The main reason behind installing RLCs is to reduce intersection‐related accidents caused because of a driver's behavior to cross the intersection when the signal turns red. By nature, if the driver is aware of the presence of RLC his or her driving behavior is bound to change. This behavioral change, however, may be intentional or unintentional. This may influence the utilization of yellow intervals resulting in a possible increase in dilemma zone, which in turn, may reduce the service capacity of the intersection. To accurately capture this capacity reduction, we present a probabilistic approach to modify the saturation flow rate formula in the Highway Capacity Manual that is currently used to calculate the capacity of signalized intersections. We introduce a new factor in the saturation flow rate calculation called red light reduction factor, to account for the capacity reduction owing to RLCs. Using field data from Baltimore, Maryland, we establish a relationship for the red light reduction factor. We then show that capacity of RLC‐equipped intersections is generally lower than that without RLCs. Although the percentage reduction in capacity of a single intersection may not seem significant, the cumulative impact of such reduction in a heavily traveled road network may be quite significant, resulting in significant loss in travel time. In future works, the systemwide capacity reduction owing to the presence of RLCs can be studied in congested transportation networks. Copyright © 2012 John Wiley & Sons, Ltd.     

Stochastic adaptive control model for traffic signal systems

An adaptive control model of a network of signalized intersections is proposed based on a discrete-time, stationary, Markov decision process. The model incorporates probabilistic forecasts of individual vehicle actuations at downstream inductance loop detectors that are derived from a macroscopic link transfer function. The model is tested both on a typical isolated traffic intersection and a simple network comprised of five four-legged signalized intersections, and compared to full-actuated control. Analyses of simulation results using this approach show significant improvement over traditional full-actuated control, especially for the case of high volume, but not saturated, traffic demand.     

Real-time estimation of turning movement counts at signalized intersections using signal phase information

A variety of sensor technologies, such as loop detectors, traffic cameras, and radar have been developed for real-time traffic monitoring at intersections most of which are limited to providing link traffic information with few being capable of detecting turning movements. Accurate real-time information on turning movement counts at signalized intersections is a critical requirement for applications such as adaptive traffic signal control. Several attempts have been made in the past to develop algorithms for inferring turning movements at intersections from entry and exit counts; however, the estimation quality of these algorithms varies considerably. This paper introduces a method to improve accuracy and robustness of turning movement estimation at signalized intersections. The new algorithm makes use of signal phase status to minimize the underlying estimation ambiguity. A case study was conducted based on turning movement data obtained from a four-leg signalized intersection to evaluate the performance of the proposed method and compare it with two other existing well-known estimation methods. The results show that the algorithm is accurate, robust and fairly straightforward for real world implementation.     

Optimization of pedestrian phase patterns at signalized intersections: a multi‐objective approach

This paper presents a multi‐objective optimization model and its solution algorithm for optimization of pedestrian phase patterns, including the exclusive pedestrian phase (EPP) and the conventional two‐way crossing (TWC) at an intersection. The proposed model will determine the optimal pedestrian phase pattern and the corresponding signal timings at an intersection to best accommodate both vehicular traffic and pedestrian movements. The proposed model is unique with respect to the following three critical features: (1) proposing an unbiased performance index for comparison of EPP and TWC by explicitly modeling the pedestrian delay under the control of TWC and EPP; (2) developing a multi‐objective model to maximize the utilization of the available green time by vehicular traffic and pedestrian under both EPP or TWC; and (3) designing a genetic algorithm based heuristic algorithm to solve the model. Case study and sensitivity analysis results have shown the promising property of the proposed model to assist traffic practitioners, researchers, and authorities in properly selecting pedestrian phase patterns at signalized intersections. Copyright © 2013 John Wiley & Sons, Ltd.     

Automated cars: Queue discharge at signalized intersections with ‘Assured-Clear-Distance-Ahead’ driving strategies

This study addresses the impacts of automated cars on traffic flow at signalized intersections. We develop and subsequently employ a deterministic simulation model of the kinematics of automated cars at a signalized intersection approach, when proceeding forward from a stationary queue at the beginning of a signal phase. In the discrete-time simulation, each vehicle pursues an operational strategy that is consistent with the ‘Assured Clear Distance Ahead’ criterion: each vehicle limits its speed and spacing from the vehicle ahead of it by its objective of not striking it, regardless of whether or not the future behavior of the vehicle ahead is cooperative. The simulation incorporates a set of assumptions regarding the values of operational parameters that will govern automated cars’ kinematics in the immediate future, which are sourced from the relevant literature.We report several findings of note. First, under a set of assumed ‘central’ (i.e. most plausible) parameter values, the time requirement to process a standing queue of ten vehicles is decreased by 25% relative to human driven vehicles. Second, it was found that the standard queue discharge model for human–driven cars does not directly transfer to queue discharge of automated vehicles. Third, a wet roadway surface may result in an increase in capacity at signalized intersections. Fourth, a specific form of vehicle-to-vehicle (V2V) communications that allows all automated vehicles in the stationary queue to begin moving simultaneously at the beginning of a signal phase provides relatively minor increases in capacity in this analysis. Fifth, in recognition of uncertainty regarding the value of each operational parameter, we identify (via scenario analysis, calculation of arc elasticities, and Monte-Carlo methods) the relative sensitivity of overall traffic flow efficiency to the value of each operational parameter.This study comprises an incremental step towards the broader objective of adapting standard techniques for analyzing traffic operations to account for the capabilities of automated vehicles.     

A new lost time estimation method for right‐turn traffic in Japan considering signal phasing and sneakers

Precise estimation of the capacity for right‐turn traffic (comparable to left‐turn traffic in the USA) is of great importance to determine signal phasing schemes at signalized intersections in Japan, where the left‐hand driving rule is valid. However, in most signal timing procedures across the world, the lost time of right‐turn traffic is simply determined by the duration of intergreen intervals and thus lacks considerations of various signal phasing and driver behavior. Meanwhile, sneakers per cycle are usually applied to account for the number of drivers completing right turns during the effective red portion of the clearance‐and‐change intervals. As a result, an initial cycle length must be hypothesized in order to assess the total number of sneakers within the analysis period. Consequently, a time‐consuming iterative calculation process often becomes necessary. Therefore, the present study aims to develop a new lost time estimation method for right‐turn traffic to overcome the aforementioned drawbacks. Lost times of right‐turn traffic under three conventional phasing plans are theoretically formulated on the basis of a time–space diagram and shock‐wave theory. The new method is validated using field data, with case studies of its application in the signal timing procedure. Results indicated that the proposed method is capable of offering more accurate estimation than conventional approaches, which leads to shorter cycle length and simplifies signal timing process by eliminating an iterative check to determine the number of sneakers. Copyright © 2012 John Wiley & Sons, Ltd.     

Investigating the applicability of exclusive pedestrian phase at two‐phase actuated controlled intersections

The exclusive pedestrian phase (EPP) has been used in many countries to promote walking around downtown areas by increasing the ease and convenience of pedestrian crossing. However, its applicability has not been systematically demonstrated, especially when an intersection is operated in actuated mode. This paper presents an extensive simulation‐based analysis of the applicability of EPP as compared with a normal concurrent pedestrian‐phase pattern at an isolated intersection controlled by actuated logic. Actuated signal control logics for EPP‐actuated and conventional concurrent pedestrian phase‐actuated controls are developed. Both of these control logics consider pedestrian crossing demands and can adapt to changes in vehicle traffic to reduce vehicle delay as well. A simulation model of a two‐phase controlled intersection is built and calibrated based on field data using VISSIM (PTV Planung Transport Verkehr AG in Karlsruhe, Germany). Extensive analysis is conducted to reveal fully the applicable EPP domain in terms of vehicle traffic demand, pedestrian demand, vehicle turning ratio, and pedestrian diagonal crossing ratio. The results show that the performance and applicable domain of EPP are jointly determined by those five factors. EPP significantly outperforms concurrent pedestrian phase if the vehicle turning ratio is greater than 0.6 and the pedestrian diagonal crossing ratio is greater than 0.6. These results can help traffic engineers in choosing the appropriate pedestrian‐phase patterns at actuated signalized intersections. Copyright © 2015 John Wiley & Sons, Ltd.