波激振动和砰击颤振对大型油船疲劳强度影响研究

文章给出线性波激振动和砰击颤振引起的大型油船结构疲劳贡献度的计算方法。基于三维线性水弹性理论可计算得到包括刚体和2节点的振动模态下的垂向弯矩的传递函数,采用谱分析法对某30万吨油船进行结构疲劳强度计算,分析波激振动对船体结构疲劳损伤影响;基于二维非线性波浪载荷程序（含砰击颤振的波浪载荷）,采用时域方法对该油船进行船体梁弯矩计算,分析砰击颤振对船体梁弯矩及疲劳载荷的影响;结果表明对于该类大型油船波激振动和砰击颤振对船体的结构疲劳损伤的影响不可忽略。     

Extensive study on the design loads used for strength assessment of tanker and bulk carrier structures

ClassNK has undertaken wide-ranging basic research covering many aspects related to the safety of ship structures, including design loads, structural analysis, strength assessment of buckling, collapse, and fatigue, and rational corrosion margins to develop new design standards which have transparency and consistency. Among the wide-ranging basic research, this article summarizes the results of extensive work on the design loads used for strength assessments of tanker and bulk carrier structures. The main aim of the research was to develop practical estimation methods of design loads with rational technical backgrounds relating to the actual loads acting on the primary structural members of tankers and bulk carriers. During this study, we proposed the following methodology. Design sea states that closely resemble the actual sea states which are considered to be the most severe for hull structures. Find practical estimation methods for the design sea states by parametric studies using the results of series calculations on representative tankers and bulk carriers. Find practical estimation methods for design regular waves which will result in the same level of stresses as those induced in irregular waves under the design sea states. We also briefly introduced some practical estimation methods for the design loads, such as ship motions, accelerations, hull-girder bending moments, and hydrodynamic pressures that are induced under design regular waves. The findings in this study have been summarized and implemented in the new design standards for tanker and bulk carrier structures.Updated from the Japanese original which won the 2003 SNAJ prize (J Soc Nav Archit Jpn 2002; 191:195–207; 2002; 191:208–220; and 2002; 192:723–733)     

逐步破坏法破损油船剩余强度研究

基于IACS共同规范研制了逐步破坏法计算完整油船极限强度和破损剩余强度的程序.考虑了船体发生搁浅碰撞后,其剩余有效剖面是非对称的,船体还可能发生不同程度倾斜的实际情况,计算了双壳油船在不同破损情况下破损船体的剩余强度,并给出了实例及结果分析.     

绿色油船发展趋势分析

以油船防污染为切入点,深入探讨单壳油船到双壳油船,再到共同规范时代油船的产生、发展变化,对未来绿色船舶发展浪潮中油船发展趋势进行分析,并针对业界应对绿色油船发展提出建议。     

Fatigue damage calculation for oil tanker and container ship structures

The fatigue behaviour of longitudinal stiffeners of oil tankers and container ships, subjected to dynamic loads, is analysed. The following dynamic load components are considered: hull girder vertical wave bending moment, alone and combined with the horizontal wave bending moment, hydrodynamic pressure and inertial forces caused by cargo acceleration.

The spectral method was selected to calculate the fatigue damage, based on S—N curves and Miner's rule. Following this approach, the fatigue damage may be calculated as a function of a stress parameter Ω_p, which represents the cumulative effect of wave induced loads in the unit of time and incorporates the combined effects of stress level and its occurring frequency.

Simple formulas for Ω_p of oil tankers and container ships are given, obtained from the results of hydrodynamic analyses performed on several ships, in different wave environments.

Several examples show the applicability of the methods to real ship structures. The method, however, still needs to be calibrated because of the simplifying hypotheses introduced in the loading conditions.     

基于共同结构规范的油船结构分析方法

以VLCC为例，着重阐述了中国船级社（CCS）自主研发的结构分析软件CCS—Tools在共同结构规范（CSR）油船设计审图中的应用。IACSJTP油船结构设计程序是CCS最新研究成果，它将使人们从繁冗的CSR评估工作中解脱出来，从而通过先进完善的计算手段完成油船的设计和校核工作。     

深水Spar钻采储运平台极限强度可靠性分析

针对一种新型的深水立柱式Spar钻采储运平台(Spar Drilling Production Storage Offloading)的结构特点进行极限强度可靠性研究。SDPSO平台的中间舱段为储油系统,其结构的安全性尤为重要,本文验证了在波浪弯矩年极值条件下其特殊储油系统结构的安全性。采用SESAM/Wadam软件对SDPSO平台进行水动力计算,利用序列统计法得到年极值短期海况,然后采用极值I型分布得到该短期海况下的波浪弯矩极值;利用ABAQUS非线性有限元软件和改进的Rosenblueth法进行SDPSO平台中舱段的极限强度计算,并得到极限承载能力的概率分布。最后基于一次二阶矩法完成SDPSO平台弯曲极限强度的可靠性计算,结果表明平台结构极限强度具有较高的安全水平,为深海立柱式海洋平台设计提供了依据和参考。     

大型油船和集装箱船静水弯矩的统计特性研究

本文介绍了国内外静水弯矩的研究现状，对Soares和Moan的经验回归公式进行了详细讨论，发现不同的研究人员对静水弯矩统计特征的认识存在相当大的差异。文中对静水弯矩均值和变异系数对船舶总纵强度安全指数的敏感度进行了分析，发现均值比变异系数更加重要。在分析和比较的基础上，根据简单可靠的原则，对集装箱船和油船的静水弯矩统计特征计算提出了如下建议：集装箱船，Cov=0．30；油船，满载（中垂）时，Cov＝0．4，压载（中拱）时，Cov=0．70。     

协调版共同结构规范对船体局部支撑构件的影响分析

IMO GBS框架下的协调版共同结构规范（CSR-H）对船舶结构设计提出新的要求。文章分析CSR-H和CSR对散货船和油船局部支撑构件（包括板与扶强材）的规范要求差异,并针对典型CSR散货船和CSR油船进行CSR-H符合性验证计算,初步归纳CSR-H对船体局部支撑构件的影响规律,可为CSR-H的研究和应用提供参考。     

Assessment of IACS-CSR implicit safety levels for buckling strength of stiffened panels for double hull tankers

The present study aims at applying structural reliability methods to assess the implicit safety levels of the buckling strength requirements for longitudinal stiffened panels implemented in the IACS Common Structural Rules (CSR) for double hull oil tankers. The buckling strength requirements considered are used in the initial stage of the hull girder scantlings’ design to control the buckling capacity of longitudinal stiffened panels subjected to the compressive loads induced by the hull girder vertical bending. The following buckling collapse failure modes are explicitly considered in the design formulation: uniaxial buckling of the plating between stiffeners, column buckling of stiffeners with attached plating and lateral-torsional buckling or tripping of stiffeners.The paper presents the procedure used to assess the implicit safety levels of the strength requirements for the three buckling collapse failure modes above mentioned, which includes the optimization of the scantlings of the plate panels and longitudinal stiffeners in order to reflect the minimum strength required by the formulation. A first order reliability formulation is adopted, and stochastic models proposed in the literature are used to quantify the uncertainty in the relevant design variables. A sample of five oil tankers representative of the range of application of the IACS-CSR design rules is considered. The effect of corrosion in the implicit safety levels is quantified based on the three corrosion levels of the Net Thickness Approach (NTA) adopted in the design rules. Sensitivity analyses are also performed to quantify the relative contribution or importance of each design random variable to the implicit safety levels.     

液货晃荡对油船结构性能的影响研究

论文研究了液货晃荡对油船的结构响应影响研究.论文对比研究了考虑液货晃荡与忽略液货晃荡影响的油船结构强度,包括设计波参数对比,最大扭矩、最大垂向弯矩、最大水平弯矩控制参数对应工况下的结构应力分布特征对比.对比研究了考虑液货晃荡与忽略液货晃荡影响的油船疲劳强度,包括满载状态下的疲劳评估结果、疲劳损伤的浪向角分布结果对比.论文针对液货晃荡对油船结构响应影响提出的研究结论,对油船的结构设计及评估具有重要的研究意义.     

Circular motion tests and uncertainty analysis for ship maneuverability

Circular motion test data and uncertainty analysis results of investigations of the hydrodynamic characteristics of ship maneuvering are presented. The model ships used were a container ship and two tankers, and the measured items were the surge and sway forces, yaw moment, propeller thrust, rudder normal and tangential forces, pitch and roll angles, and heave. The test parameters were the oblique angle and yaw rate for the conditions of a hull with a rudder and propeller in which the rudder angle was set to zero and the propeller speed was set to the model self-propulsion conditions. Carriage data showing the accuracy of the towing conditions in the circular motion test are also presented. It was confirmed that the uncertainties in the hydrodynamic forces such as the surge and sway forces, yaw moment, rudder tangential and normal forces, and propeller thrust were fairly small. The reported uncertainty analysis results of the circular motion test data may be beneficial in validating data quality and in discussing reliability for simulation of ship maneuvering performance.     

基于有限元力矩阵精确确定三舱段有限元模型边界力的计算方法

双壳油船结构统一规范要求进行三舱段的有限元模型强度计算.本文采用有限元力矩阵节点力计算方法,可以精确计算确定三舱段的有限元模型两端部应施加的边界力(弯矩和剪力),为正确实施三舱段的有限元模型的边界力计算提供了实用的计算方法.     

基于试验获取主应力应变曲线的油船极限强度评估研究(英文)

A geometrically similar scaling was made from small-scale specimen to full-scale stiffened panels and then their collapse behaviour is investigated. It is considered that the stiffened panel compressive ultimate strength test was designed according to geometrical scaling laws so that the output of the test could be used as representative of the stiffened panels of the compressive zone of a tanker hull subjected to vertical bending moment. The ultimate strength of a tanker hull is analysed by a FE analysis using the experimentally developed master stress-strain curves which are obtained by the beam tension test and the compressive test of the stiffened panel, and are then compared with the result achieved by the progressive collapse method.     

Ultimate strength assessment of a tanker hull based on experimentally developed master curves

A geometrically similar scaling was made from small-scale specimen to full-scale stiffened panels and then their collapse behaviour is investigated. It is considered that the stiffened panel compressive ultimate strength test was designed according to geometrical scaling laws so that the output of the test could be used as representative of the stiffened panels of the compressive zone of a tanker hull subjected to vertical bending moment. The ultimate strength of a tanker hull is analysed by a FE analysis using the experimentally developed master stress-strain curves which are obtained by the beam tension test and the compressive test of the stiffened panel, and are then compared with the result achieved by the progressive collapse method.     

超大型油船压载水舱分舱的优化研究

通过对国际船级社协会（IACS）URS11规范和其最新建议案的研究,结合已有VLCC船压载水舱分舱布置型式的分析,提出一种符合URS11最新要求的VLCC压载水舱分舱的优化方案,以达到降低船体设计最大中拱静水弯矩的目的。     

船体梁静水载荷效应统计预报

船体梁静水剪力、弯矩等是由装载状态决定的载荷效应。营运船舶装载记录表明，实际装载状态具有不确定性，由此导致载荷效应发生变异，其统计特性可利用回归公式或随机模拟原理进行估算或预报。通过对油船、散货船、滚装船及集装箱船约2000种随机工况所作的统计分析，表明其静水弯矩等随装载偏差的变化近似于正态分布律，并具有比船体中剖面模数或钢材屈服极限更为显著的变异性。在船舶结构可靠性分析或理性设计中，合理估算并预报这种及异性是必要的。     

Comparative reliability analysis of ships under vector-load processes

This paper deals with reliability analysis of ships under vector-load processes. Failure is expressed by multiple response variables. Different methods can be used to assess failure probability, primary among them are the time-independent and out-crossing (up-crossing) rate methods. This paper describes the procedure for performing reliability analysis of ships under vector-load processes by the out-crossing rate method. Alternative methods based on piecewise linear or continuous modeling of failure surface are explored for calculating the out-crossing rate and compared. The methods are exemplified by calculating the conditional probability of a damaged double hull oil tanker under combined vertical and horizontal bending moments.     

无压载水舱船型开发和前景分析

阐述了国外的无压载水舱的贯通流船体和V型船体,并以6500t无压载水舱油船为例,提供了主尺度、线型和技术参数。通过与常规油船的分析比较,显示该新船型的优势。为推动无压载水舱的其他船型的开发提供了指导方案。     

Supply and demand of new oil tankers

This paper examines the world-wide supply and demand for new oil tankers. A simultaneous supply and demand model is developed and estimated using two-stage least squares techniques and empirical data from 1972 to 1983. The relationships between tanker newbuilding orders and prices, and other relevant market factors are analysed. Major factors affecting the tanker new building market are identified. The results indicate that: oil price and second-hand tanker price are predominant factors influencing future newbuilding demand; a moderate decrease in laid-up tonnage would not induce a significant increase in newbuilding orders; shipbuilding capacity is a more influential factor for the short-run supply of new tankers than shipbuilding cost. Technological change has also played an important role in the market.