Optimizing signals for arterials experiencing heavy mixed scooter-vehicle flows

Recognizing the increasing popularity of scooters among urban commuters in developing countries and the significant impacts of their dynamic maneuverability on the progression of mixed traffic, this study presents a simulation-based signal optimization model for arterials experiencing heavy scooter-vehicle flows. The proposed model consists of a macroscopic simulation and a signal optimization module, where the former functions to capture the interactions between scooter and passenger-car flows over the process of discharging, propagation, and formation of intersection queues. The latter offers a specially-designed algorithm to search for the optimal signal plan and arterial offsets, based on the complex departure and arrival patterns of mixed flows estimated with the simulation module. To account for scooters’ unique parallel moving and queue patterns in a travel lane, the proposed signal module has adopted the sub-lane concept in estimating the mixed-flow queue distribution across lanes and their discharging flow rates. The results of extensive experimental analyses with various mixed-flow scenarios confirm that the proposed model offers the potential for signal design for arterials plagued by heavy scooter-vehicle mixed flows.     

Development of signal optimization models for asymmetric two-leg continuous flow intersections

Despite extensive studies have been reported to address the operational issues of full Continuous Flow Intersection (CFI) in the literature, the asymmetric two-leg CFI, which is more applicable in practice, has not received adequate attentions yet. To satisfy such need, this study develops two signal optimization models for asymmetric CFI based on its unique geometric features. The first proposed model, following a two-step procedure, determines the cycle length, phase design and sequence, and green split in the first step and optimizes intersection offset in the second step. To benefit both intersections’ capacity maximization and signal progression design by optimizing phase plan and sequence, the second proposed model takes the Mixed-Integer-Linear-Programming (MILP) technique to concurrently optimize all signal control variables. With extensive case studies on a field site in Maryland, the simulation results prove that the proposed models can effectively provide signal progression to critical path-flows and prevent the potential queue spillover on the short turning bays/links. Further comparisons between the two proposed models reveal that the second model is more flexible in designing phase plan but the first model performs better in reducing link queue length.     

Model for the capacity of the urban signal intersection with work zone

Work zones exist widely on urban arterials in the cities that are undergoing road construction or maintenance. However, the existing studies on arterial work zones are very limited, especially on the work zones at urban intersections, although they have a severe negative impact on the urban traffic system. For the first time, this study focuses on how work zones reduce intersection capacity. A type of widely observed work zone, the straddling work zone that straddles on a road segment and an intersection, is studied. A linear regression model and a multiplicative model suggested by Highway Capacity Manual are proposed respectively to determine the saturation flow rate of the signal intersection with the straddling work zone. The data of 22 straddling work zones are collected and used to evaluate the performances of the proposed models. The results display that the linear regression model outperforms the multiplicative model suggested by Highway Capacity Manual. The study also reveals that reducing approach (or exit) lanes and the mixture of motor vehicles and non‐motor vehicles (and pedestrians) can significantly decrease the capacity of the intersection with straddling work zone. Therefore, in setting a straddling work zone, workers should try to ensure that the intersection approach and exit are unobstructed and set a separation for non‐motors and pedestrians to avoid mixed traffic flow. Copyright © 2016 John Wiley & Sons, Ltd.     

Self-organizing traffic signals using secondary extension and dynamic coordination

Actuated traffic signal control logic has many advantages because of its responsiveness to traffic demands, short cycles, effective use of capacity leading to and recovering from oversaturation, and amenability to aggressive transit priority. Its main drawback has been its inability to provide good progression along arterials. However, the traditional way of providing progression along arterials, coordinated–actuated control with a common, fixed cycle length, has many drawbacks stemming from its long cycle lengths, inflexibility in recovering from priority interruptions, and ineffective use of capacity during periods of oversaturation. This research explores a new paradigm for traffic signal control, “self-organizing signals,” based on local actuated control but with some additional rules that create coordination mechanisms. The primary new rules proposed are for secondary extensions, in which the green may be held to serve an imminently arriving platoon, and dynamic coordination, in which small groups of closely spaced signals communicate with one another to cycle synchronously with the group’s critical intersection. Simulation tests in VISSIM performed on arterial corridors in Massachusetts and Arizona show overall delay reductions of up to 14% compared to an optimized coordinated–actuated scheme where there is no transit priority, and more than 30% in scenarios with temporary oversaturation. Tests also show that with self-organizing control, transit signal priority can be more effective than with coordinated–actuated control, reducing transit delay by about 60%, or 12 to 14 s per intersection with little impact on traffic delay.     

A decomposition scheme for estimating dynamic origin–destination flows on actuation-controlled signalized arterials

This paper presents a decomposition framework for estimating dynamic origin–destination (O–D) flows on actuation-controlled signalized arterials from link counts, mainly addressing the issues of incomplete information and the large number of O–D pairs. The framework decomposes the original high-dimensional problem into much smaller sub-problems at the intersection and corridor levels. At the intersection level, turning movements are inferred with incomplete information; at the corridor level, the final estimates of O–D flows are constructed as weighted averages of the estimates from the column and row decompositions. Numerical examples are presented to demonstrate the effectiveness and the computational efficiency of the decomposition framework.     

Development of a delay model for unsignalized intersections applicable to traffic assignment

Abstract

This paper develops a model for estimating unsignalized intersection delays which can be applied to traffic assignment (TA) models. Current unsignalized intersection delay models have been developed mostly for operational purposes, and demand detailed geometric data and complicated procedures to estimate delay. These difficulties result in unsignalized intersection delays being ignored or assumed as a constant in TA models.

Video and vehicle license plate number recognition methods are used to collect traffic volume data and to measure delays during peak and off-peak traffic periods at four unsignalized intersections in the city of Tehran, Iran. Data on geometric design elements are measured through field surveys. An empirical approach is used to develop a delay model as a function of influencing factors based on 5- and 15-min time intervals. The proposed model estimates delays on each approach based on total traffic volumes, rights-of-way of the subject approach and the intersection friction factor. The effect of conflicting traffic flows is considered implicitly by using the intersection friction factor. As a result, the developed delay model guarantees the convergence of TA solution methods.

A comparison between delay models performed using different time intervals shows that the coefficients of determination, R ², increases from 43.2% to 63.1% as the time interval increases from 5- to 15-min. The US Highway Capacity Manual (HCM) delay model (which is widely used in Iran) is validated using the field data and it is found that it overestimates delay, especially in the high delay ranges.     

Speed variation during peak and off-peak hours on urban arterials in Shanghai

Increased speed variation on urban arterials is associated with reductions in both operational performance and safety. Traffic flow, mean speed, traffic control parameters and geometric design features are known to affect speed variation. An exploratory study of the relationships among these variables could provide a foundation for improving the operational and safety performance of urban arterials, however, such a study has been hampered by problems in measuring speeds. The measurement of speed has traditionally been accomplished using spot speed collection methods such as radar, laser and loop detectors. These methods can cover only limited locations, and consequently are not able to capture speed distributions along an entire network, or even throughout any single road segment. In Shanghai, it is possible to acquire the speed distribution of any roadway segment, over any period of interest, by capturing data from Shanghai’s 50,000+ taxis equipped with Global Positional Systems (GPS). These data, hereafter called Floating Car Data, were used to calculate mean speed and speed variation on 234 road segments from eight urban arterials in downtown Shanghai. Hierarchical models with random variables were developed to account for spatial correlations among segments within each arterial and heterogeneities among arterials. Considering that traffic demand changes throughout the day, AM peak, Noon off-peak, and PM peak hours were studied separately. Results showed that increases in number of lanes and number of access points, the presence of bus stops and increases in mean speed were all associated with increased speed variation, and that increases in traffic volume and traffic signal green times were associated with reduced speed variation. These findings can be used by engineers to minimize speed differences during the road network planning stage and continuing through the traffic management phase.     

A shockwave profile model for traffic flow on congested urban arterials

In this paper a new traffic flow model for congested arterial networks, named shockwave profile model (SPM), is presented. Taking advantage of the fact that traffic states within a congested link can be simplified as free-flow, saturated, and jammed conditions, SPM simulates traffic dynamics by analytically deriving the trajectories of four major shockwaves: queuing, discharge, departure, and compression waves. Unlike conventional macroscopic models, in which space is often discretized into small cells for numerical solutions, SPM treats each homogeneous road segment with constant capacity as a section; and the queuing dynamics within each section are described by tracing the shockwave fronts. SPM is particularly suitable for simulating traffic flow on congested signalized arterials especially with queue spillover problems, where the steady-state periodic pattern of queue build-up and dissipation process may break down. Depending on when and where spillover occurs along a signalized arterial, a large number of queuing patterns may be possible. Therefore it becomes difficult to apply the conventional approach directly to track shockwave fronts. To overcome this difficulty, a novel approach is proposed as part of the SPM, in which queue spillover is treated as either extending a red phase or creating new smaller cycles, so that the analytical solutions for tracing the shockwave fronts can be easily applied. Since only the essential features of arterial traffic flow, i.e., queue build-up and dissipation, are considered, SPM significantly reduces the computational load and improves the numerical efficiency. We further validated SPM using real-world traffic signal data collected from a major arterial in the Twin Cities. The results clearly demonstrate the effectiveness and accuracy of the model. We expect that in the future this model can be applied in a number of real-time applications such as arterial performance prediction and signal optimization.     

An investigation of multiplier effects generated by implementing queue jump lanes at multiple intersections

This paper investigates the combination effects of queue jump lanes (QJLs) on signalised arterials to establish if a multiplier effect exists, that is, the benefit from providing QJLs at multiple intersections is higher than the sum of benefits from providing them individually at each of those intersections. To explore the combination effects on bus delay and total person delay, a delay estimation model is developed using kinematic wave theory, kinematic equations and Monte Carlo simulation. In addition, to investigate the combination effects in offset settings optimised for bus delay or total person delay, offset optimisation models are proposed. Validation results using traffic micro‐simulation indicate the effectiveness and computational efficiency of the proposed models. Results of a modelling test bed suggest that providing QJLs at multiple intersections can create a multiplier effect on one‐directional bus delay savings with signal offsets that provide bus progression. Furthermore, optimising offsets to minimise bus delay tends to create a multiplier effect on one‐directional bus delay savings, particularly when variations in dwell times are not high. The reason for the multiplier effect may be that providing QJLs reduces variations in bus travel times, which makes signal coordination for buses perform more effectively. From a policy perspective, the existence of a multiplier effect suggests that a corridor‐wide scale implementation of QJLs has considerable merit. Copyright © 2016 John Wiley & Sons, Ltd.     

A continuous-flow-intersection-lite design and traffic control for oversaturated bottleneck intersections

Oversaturation has become a severe problem for urban intersections, especially the bottleneck intersections that cause queue spillover and network gridlock. Further improvement of oversaturated arterial traffic using traditional mitigation strategies, which aim to improve intersection capacity by merely adjusting signal control parameters, becomes challenging since exiting strategies may (or already) have reached their “theoretical” limits of optimum. Under such circumstance, several novel unconventional intersection designs, including the well-recognized continuous flow intersection (CFI) design, are originated to improve the capacity at bottleneck intersections. However, the requirement of installing extra sub-intersections in a CFI design would increase vehicular stops and, more critically, is unacceptable in tight urban areas with closed spaced intersections. To address these issues, this research proposes a simplified continuous flow intersection (called CFI-Lite) design that is ideal for arterials with short links. It benefits from the CFI concept to enable simultaneous move of left-turn and through traffic at bottleneck intersections, but does not need installation of sub-intersections. Instead, the upstream intersection is utilized to allocate left-turn traffic to the displaced left-turn lane. It is found that the CFI-Lite design performs superiorly to the conventional design and regular CFI design in terms of bottleneck capacity. Pareto capacity improvement for every traffic stream in an arterial system can be achieved under effortless conditions. Case study using data collected at Foothill Blvd in Los Angeles, CA, shows that the new design is beneficial in more than 90% of the 408 studied cycles. The testing also shows that the average improvements of green bandwidths for the synchronized phases are significant.     

Estimating link travel time functions for heterogeneous traffic flows on freeways

Oversized vehicles, such as trucks, significantly contribute to traffic delays on freeways. Heterogeneous traffic populations, that is, those consisting of multiple vehicles types, can exhibit more complicated travel behaviors in the operating speed and performance, depending on the traffic volume as well as the proportions of vehicle types. In order to estimate the component travel time functions for heterogeneous traffic flows on a freeway, this study develops a microscopic traffic‐simulation based four‐step method. A piecewise continuous function is proposed for each vehicle type and its parameters are estimated using the traffic data generated by a microscopic traffic simulation model. The illustrated experiments based on VISSIM model indicate that (i) in addition to traffic volume, traffic composition has significant influence on the travel time of vehicles and (ii) the respective estimations for travel time of heterogeneous flows could greatly improve their estimation accuracy. Copyright © 2016 John Wiley & Sons, Ltd.     

Microscopic pedestrian simulation model combined with a tactical model for route choice behaviour

This study proposes a microscopic pedestrian simulation model for evaluating pedestrian flow. Recently, several pedestrian models have been proposed to evaluate pedestrian flow in crowded situations for the purpose of designing facilities. However, current pedestrian simulation models do not explain the negotiation process of collision avoidance between pedestrians, which can be important for representing pedestrian behaviour in congested situations. This study builds a microscopic model of pedestrian behaviour using a two-player game and assuming that pedestrians anticipate movements of other pedestrians so as to avoid colliding with them. A macroscopic tactical model is also proposed to determine a macroscopic path to a given destination. The results of the simulation model are compared with experimental data and observed data in a railway station. Several characteristics of pedestrian flows such as traffic volume and travel time in multidirectional flows, temporal–spatial collision avoidance behaviour and density distribution in the railway station are reproduced in the simulation.     

Short-term prediction of border crossing time and traffic volume for commercial trucks: A case study for the Ambassador Bridge

Short-term forecasting of traffic characteristics, such as traffic flow, speed, travel time, and queue length, has gained considerable attention from transportation researchers and practitioners over past three decades. While past studies primarily focused on traffic characteristics on freeways or urban arterials this study places particular emphasis on modeling the crossing time over one of the busiest US–Canada bridges, the Ambassador Bridge. Using a month-long volume data from Remote Traffic Microwave Sensors and a yearlong Global Positioning System data for crossing time two sets of ANN models are designed, trained, and validated to perform short-term predictions of (1) the volume of trucks crossing the Ambassador Bridge and (2) the time it takes for the trucks to cross the bridge from one side to the other. The prediction of crossing time is contingent on truck volume on the bridge and therefore separate ANN models were trained to predict the volume. A multilayer feedforward neural network with backpropagation approach was used to train the ANN models. Predicted crossing times from the ANNs have a high correlation with the observed values. Evaluation indicators further confirmed the high forecasting capability of the trained ANN models. The ANN models from this study could be used for short-term forecasting of crossing time that would support operations of ITS technologies.     

A virtual vehicle probe model for time-dependent travel time estimation on signalized arterials

Estimation of time-dependent arterial travel time is a challenging task because of the interrupted nature of urban traffic flows. Many research efforts have been devoted to this topic, but their successes are limited and most of them can only be used for offline purposes due to the limited availability of traffic data from signalized intersections. In this paper, we describe a real-time arterial data collection and archival system developed at the University of Minnesota, followed by an innovative algorithm for time-dependent arterial travel time estimation using the archived traffic data. The data collection system simultaneously collects high-resolution “event-based” traffic data including every vehicle actuations over loop detector and every signal phase changes from multiple intersections. Using the “event-based” data, we estimate time-dependent travel time along an arterial by tracing a virtual probe vehicle. At each time step, the virtual probe has three possible maneuvers: acceleration, deceleration and no-speed-change. The maneuver decision is determined by its own status and surrounding traffic conditions, which can be estimated based on the availability of traffic data at intersections. An interesting property of the proposed model is that travel time estimation errors can be self-corrected, because the trajectory differences between a virtual probe vehicle and a real one can be reduced when both vehicles meet a red signal phase and/or a vehicle queue. Field studies at a 11-intersection arterial corridor along France Avenue in Minneapolis, MN, demonstrate that the proposed model can generate accurate time-dependent travel times under various traffic conditions.     

Speed,travel time and delay for intersections and road segments in the Montreal network using cyclist Smartphone GPS data

Very little is known about cyclist speeds and delays at the disaggregate level of each road segment and intersection in an entire city network. Speeds and delays serve as vital information for planning, navigation and routing purposes including how they differ for different times of the day and across road and bicycle facility types, after controlling for other factors. In this work, we explore the use of recent GPS cyclist trip data, from the Mon RésoVélo Smartphone application, to identify different performance measures such as travel time, speed and delay at the level of the entire network of roads and intersections on the island of Montreal. Also, a linear regression model is formulated to identify the geometric design and built environment characteristics affecting cyclist speeds on road segments. Among other results, on average, segment speeds are greater along arterials than on local streets and greater along segments with bicycle infrastructure than those without. Incorporating different measures of cyclist personality in the models revealed that the following characteristics all affect cyclist speeds along segments, each cyclist’s average speed on uphill, downhill and level segments as well as geometric design and built environment characteristics. The model results also identify that the factors that increase cyclist speeds along segments include, segments which have cyclists biking for work or school related purposes, segments used during morning peak and segments which do not have signalized intersections at either end.     

Urban traffic state estimation: Fusing point and zone based data

Loop detectors are the oldest and widely used traffic data source. On urban arterials, they are mainly installed for signal control. Recently state-of-the art Bluetooth MAC Scanners (BMS) has significantly captured the interest of stakeholders for exploiting it for area-wide traffic monitoring. Loop detectors provide flow – a fundamental traffic parameter; whereas BMS provides individual vehicle travel time between BMS stations. Hence, these two data sources complement each other, and if integrated should increase the accuracy and reliability of the traffic state estimation.This paper proposed a model that integrates loops and BMS data for seamless travel time and density estimation for urban signalised network. The proposed model is validated using both real and simulated data and the results indicate that the accuracy of the proposed model is over 90%.     

A dynamic evacuation model for pedestrian–vehicle mixed-flow networks

In urban emergency evacuation, a potentially large number of evacuees may depend either on transit or other modes, or need to walk a long distance, to access their passenger cars. In the process of approaching the designated pick-up points or parking areas for evacuation, the massive number of pedestrians may cause tremendous burden to vehicles in the roadway network. Responsible agencies often need to contend with congestion incurred by massive vehicles emanating from parking garages, evacuation buses generated from bus stops, and the conflicts between evacuees and vehicles at intersections. Hence, an effective plan for such evacuation needs to concurrently address both the multi-modal traffic route assignment and the optimization of network signal controls for mixed traffic flows. This paper presents an integrated model to produce the optimal distribution of vehicle and pedestrian flows, and the responsive network signal plan for massive mixed pedestrian–vehicle flows within the evacuation zone. The proposed model features its effectiveness in accounting for multiple types of evacuation vehicles, the interdependent relations between pedestrian and vehicle flows via some conversion locations, and the inevitable conflicts between intersection turning vehicle and pedestrian flows. An illustrating example concerning an evacuation around the M&T stadium area has been presented, and the results indicate the promising properties of our proposed model, especially on reflecting the complex interactions between vehicle and pedestrian flows and the favorable use of high-occupancy vehicles for evacuation operations.     

Estimating performance of traffic signals based on link travel times

Recent advances in communication and computing technology have made travel time measurements more available than ever before. In urban signalized arterials, travel times are strongly influenced by traffic signals. This study presents a novel method based on well‐known principles to estimate traffic signal performance (or more precisely their major “through” movements) based on travel time measurements. The travel times were collected between signals in the field by using point‐to‐point travel time measurement technologies. Closed‐circuit television cameras and signal databases were used to collect traffic demand and signal timings, respectively. Then, the volume/capacity ratio of major downstream signal movements was computed based on demand and signal timings. This volume/capacity ratio was then correlated with travel times on the relevant intersection approach. The best volume‐delay function was found, along with many other functions, to fit the field data. This volume‐delay function was then used to estimate volume/capacity ratios and, indirectly, a few other signal performance metrics. The method, called travel time‐based signal performance measurements, was automated and displayed on a Google Map. The findings show that the proposed method is accurate and robust enough to provide necessary information about signal performance. A newly developed volume‐delay function was found to work just slightly better than the Bureau of Public Roads curve. Several issues, which may reduce the accuracy of the proposed method, are identified, and their solutions are proposed for future research. Copyright © 2016 John Wiley & Sons, Ltd.     

An intersection turning movement estimation procedure based on path flow estimator

Estimation of intersection turning movements is one of the key inputs required for a variety of transportation analysis, including intersection geometric design, signal timing design, traffic impact assessment, and transportation planning. Conventional approaches that use manual techniques for estimation of turning movements are insensitive to congestion. The drawbacks of the manual techniques can be amended by integrating a network traffic model with a computation procedure capable of estimating turning movements from a set of link traffic counts and intersection turning movement counts. This study proposes using the path flow estimator, originally used to estimate path flows (hence origin–destination flows), to derive not only complete link flows, but also turning movements for the whole road network given some counts at selected roads and intersections. Two case studies using actual traffic counts are used to demonstrate the proposed intersection turning movement estimation procedure. Copyright © 2010 John Wiley & Sons, Ltd.     

Lane-based real-time queue length estimation using license plate recognition data

License plate recognition (LPR) data are emerging data sources that provide rich information in estimating the traffic conditions of urban arterials. While large-scale LPR system is not common in US, last few years have seen rapid developments and implementations in many other parts of world (e.g. China, Thailand and Middle East). Due to privacy issues, LPR data are seldom available to research communities. However, when available, this data source can be valuable in estimating real-time operational metrics in transportation systems. This paper proposes a lane-based real-time queue length estimation model using the license plate recognition (LPR) data. In the model, an interpolation method based on Gaussian process is developed to reconstruct the equivalent cumulative arrival–departure curve for each lane. The missing information for unrecognized or unmatched vehicles is obtained from the reconstructed arrival curve. With the complete arrival and departure information, a car-following based simulation scheme is applied to estimate the real-time queue length for each lane. The proposed model is validated using ground truth information of the maximum queue lengths from the city of Langfang in China. The results show that the model can capture the variations in queue lengths in the ground truth data, and the maximum queue length for each signal cycle can be estimated with a reasonable accuracy. The estimated queue length information using the proposed model can serve as a useful performance metric for various real-time traffic control applications.