Effect of UWS injection at low exhaust gas temperature on NO<Subscript>x</Subscript> removal efficiency of diesel engine

Urea-SCR systems have been widely used in diesel vehicles according to the strengthened NO_x (Nitrogen Oxides) emission standard. The NO_x removal efficiencies of the latest well optimized urea-SCR system are above 90 % at moderate exhaust gas temperature of 250 ~ 450 °C. However, a large amount of NO_x is emitted from diesel vehicles at cold start or urban driving conditions, when the exhaust gas temperature is not high enough for SCR catalyst activation. Although many researchs have been stuied to improve NO_x conversion efficiency at these low temperature conditions, it is still one of important technical issues. In this study, the effect of UWS injection at low exhaust gas temperature conditions is studied. This study uses a 3.4 L diesel engine equipped with a commertial urea SCR system. As a result, it is found that about 5 % of NO_x removal efficiency is improved in the NRTC test when UWS injection starts at the SCR inlet temperature of 150 °C compared to 200 °C. It is also found that urea deposits can be formed on the wall of exhaust pipe, when the local wall temperature is lower than temperature of urea decomposition.     

Computational study on the effects of volume ratio of DOC/DPF and catalyst loading on the PM and NOx emission control for heavy-duty diesel engines

The use of a diesel particulate filter (DPF) in a diesel aftertreatment system has proven to be an effective and efficient method for removing particulate matter (PM) in order to meet more stringent emission regulations without hurting engine performance. One of the favorable PM regeneration technologies is the NO₂-assisted regeneration method due to the capability of continuous regeneration of PM under a much lower temperature than that of thermal regeneration. In the present study, the thermal behavior of the monolith during regeneration and the conversion efficiency of NO₂ from NO with an integrated exhaust system of a diesel oxidation catalyst (DOC) and DPF have been predicted by one-channel numerical simulation. The simulation results of the DOC, DPF, and integrated DOC-DPF models are compared with experimental data to verify the accuracy of the present model for the integrated DOC and DPF modeling. The effects of catalyst loading inside the DOC and the volume ratio between the DOC and DPF on the pressure drop, the conversion efficiency, and the oxidation rate of PM, have been numerically investigated. The results indicate that the case of the volume ratio of ‘DOC/DPF=1.5’ within the same diameter of both monoliths produced close to the maximum conversion efficiency and oxidation rate of PM. Under the engine operating condition of 175 kW at 2200 rpm, 100% load with a displacement of 8.1, approximately 55 g/ft³ of catalyst (Pt) loading inside the DOC with the active Pt surface of 5.3 m²/g_pt was enough to maximize the conversion efficiency and oxidation rate of PM.     

分子筛型SCR对车用柴油机排放改善的试验研究

商用车柴油机多采用DOC+SCR的后处理系统来满足国Ⅳ、国Ⅴ排放标准的要求,而不同类型SCR的催化特性对最终污染物排放影响也不同。试验获取了一支铜基分子筛型SCR,基于1台2.8L柴油机和一支钒基SCR,运行了车用柴油机稳态循环(ESC)和瞬态排放循环(ETC),研究并分析了其对柴油机污染物的减排特性。结果表明,相较于钒基SCR,运行ETC循环时分子筛型SCR对发动机NOx和PM排放的减排效率分别提升19%和33%;分子筛型SCR对NOx的低温转化效率更高,且由于对排气流量不敏感,在高空速工况下其转化效率显著高于钒基SCR;分子筛型SCR对颗粒物个数的减排效率弱于钒基SCR,达7%以上,容易将大质量颗粒物分解为小质量颗粒物;两种SCR均对CO和HC具有一定的减排效果,减排率可达20%左右。     

前置DOC对SCR系统柴油机NO_x排放的影响

对装配前置DOC和无DOC的SCR系统柴油机进行稳态和瞬态试验,研究了前置DOC在不同循环状态下对NOx排放的影响。结果表明:前置DOC能显著提高SCR入口处NO2与NOx的体积比V(NO2)∶V(NOx),加速SCR反应,提高NOx转化效率,改善NOx排放;在ESC非怠速工况下,DOC对V(NO2)∶V(NOx)的影响会随着排气中氧含量和排气温度、空速的提高逐渐降低;温度超过一定范围时,NH3对O2的选择性突然提高,V(NO2)∶V(NOx)对NOx转化效率的影响将减小;DOC内氧化反应产生的热量有限,不足以提高SCR入口处排气温度,而DOC陶瓷载体的储热特性在瞬态循环下会对SCR入口温度产生一定影响,但这并不是改善NOx排放的主要原因。     

Heat exchanger/catalytic system for reducing the exhaust emissions from diesel engines

A system has been researched over the past 3 years for reducing the exhaust pollutants from diesel engines for light commercial vehicles. The system researched achieves Euro 6 standards for reduction of polluting gases (CO, HC, PM, NO). It consists of 4 main sections: 1. A heater and heat exchanger (HE); 2. A CO/HC oxidising catalyst (D°C); 3. Pt catalyst on a diesel particulate filter (DPF); 4. A NO reducing reaction (SCR) within the DPF. The system operates as follows. The exhaust gas contains oxidising gases, namely both O₂ and NO₂. The levels of CO and HC are oxidised by O₂ to CO₂ for temperatures above 200°C. Carbon (PM) is oxidised to CO₂ by NO₂ but requires a temperature above 250°C. The operating exhaust temperature of 300°C is ideal for the removal of NO by using the Pt catalyst and the CO generated within the DPF. The heater is required to be able to raise the exhaust temperature at any time to 300°C in order to optimise the performance of the system, since diesel engine exhaust temperatures vary between 160°C (slow speeds) to 350°C (high speeds). Considerable heat is required (??3 kW) to maintain the exhaust gas for a 2l engine at 300°C for engine idle conditions. Therefore a heat exchanger is required to re-circulate the input heat and thereby reduce the maximum power consumption to a maximum of 500W over the engine full operating test cycle. This energy is supplied by the engine battery and alternator. Experimental results have been obtained for the exhaust from a Kubota diesel engine and the reductions in exhaust emissions of 83% (CO/ HC), 58% (NOx) and 99% (PM) were obtained. The PM was continuously cleaned so that there was no build up of back pressure.     

Measurement of soot oxidation with No<Subscript>2</Subscript>-O<Subscript>2</Subscript>-H<Subscript>2</Subscript>O in a flow reactor simulating diesel engine DPF

Understanding the mechanism of carbon oxidation is important for the successful modeling of diesel particulate filter regeneration. Characteristics of soot oxidation were investigated with carbon black (Printex-U). A flow reactor system that could simulate the condition of a diesel particulate filter and diesel exhaust gas was designed. Kinetic constants were derived and the reaction mechanisms were proposed using the experimental results and a simple reaction scheme, which approximated the overall oxidation process in TPO as well as CTO. From the experiments, the apparent activation energy for carbon oxidation with NO₂-O₂-H₂O was determined to be 40±2 kJ/mol, with the first order of carbon in the range of 10∼90% oxidation and a temperature range of 250∼500°C. This value was exceedingly lower than the activation energy of NO₂-O₂ oxidation, which was 60±3 kJ/mol. When NO₂ exists with O₂ and H₂O, the reaction rate increases in proportion to NO₂. It increases nonlinearly with O₂ or H₂O concentration when the other two oxidants are fixed.     

Comparison of HC species from diesel combustion modes and characterization of a heat-up doc formulation

This study summarizes engine speed and load effects on HC species emissions from premixed charge compression ignition (PCI) and conventional diesel combustion, and it evaluates diesel oxidation catalyst (DOC) formulations on a gas flow reactor for the purpose of diesel particulate filter regeneration or lean NO_x trap desulfation. HC emissions are sampled simultaneously by a Tedlar bag for light HC species and by a Tenax TA™ adsorption trap for semi-volatile HC species, and they are analyzed by gas chromatography with a flame ionization detector. The bulk temperature and residence time during combustion are key parameters that are important for understanding the effects of speed and load on engine-out HC emissions. The degree of post-flame oxidation is higher in PCI than in conventional combustion, and it is increased for PCI with a higher speed and load, as indicated by a lower fuel alkanes/THC ratio, a higher alkenes/fuel alkanes ratio, and a higher methane/THC ratio. Ethene and n-undecane are two representative HC species, and they are used as a surrogate mixture in the gas flow reactor to simulate PCI and conventional combustion with in-cylinder post fuel injection. Among the three DOC formulations tested, the catalyst with constituent precious metals of platinum and palladium (PtPd) showed the best light-off performance, followed by PtPd with an addition of cerium dioxide (PtPd+CeO₂), and platinum (Pt), regardless of exhaust compositions. Conventional combustion exhaust composition shows a lower light-off temperature than that of PCI, regardless of catalyst formulation.     

某柴油机催化器性能的CFD模拟分析

在某柴油机催化转化器的设计开发阶段,需要对其催化转化器进行分析,目的是找出优化措施。使用FIRE软件对优化前和优化后的DOC和SCR进行了CFD分析。结果表明：优化前的DOC和SCR在入口段扩张管存在漩涡,出现流动分离现象;优化后的DOC和SCR消除了漩涡,气流速度均匀性系数提高了。     

Sliding-mode observer for urea-selective catalytic reduction (SCR) mid-catalyst ammonia concentration estimation

This paper presents an observer design for SCR mid-catalyst ammonia concentration estimation using tailpipe NO_x and ammonia sensors. Urea-SCR has been popularly used by Diesel engine powered vehicles to reduce NO_x emissions in recent years. It utilizes ammonia, converted from urea injected at upstream of the catalyst, as the reductant to catalytically convert NO_x emissions to nitrogen. To simultaneously achieve high SCR NO_x conversion efficiency and low tailpipe ammonia slip, it is desirable to control the ammonia storage distribution along the SCR catalyst. Such a control method, however, requires a mid-catalyst ammonia sensor. The observer developed in this paper can replace such a mid-catalyst ammonia sensor and be used for SCR catalyst ammonia distribution control as well as serves for fault diagnosis purpose of the mid-catalyst ammonia sensor. The stability of the observer was shown based on the sliding mode approach and analyzed by simulations. Experimental validation of the observer was also conducted based on a medium-duty Diesel engine two-catalyst SCR system setup with emission sensors.     

SCR系统降低柴油机NOx排放的试验研究

设计了SCR系统反应器,制备了TiO2-WO3-V2O5催化剂,在6106柴油机上进行了台架试验,以验证SCR系统对NOx排放的转化效率.试验结果表明,在温度为350～500℃、空速为60 000 h-1时,SCR系统的NOx转化率可达到50%～60%.最后分析了SCR系统NOx转化率相对不高的原因.     

Urea-SCR system optimization with various combinations of mixer types and decomposition pipe lengths

The demand for NO_x after-treatment system has increased dramatically due to the stricter NO_x emission regulations for diesel vehicles. The urea-SCR system is one of the NO_x after-treatment methods found to be quite effective to meet the regulation requirement enforced by various authorities including the Euro-6. In order to develop an effective urea-SCR system, it is critical to establish an even distribution of reductant over the catalyst surface since this favorable distribution can increase reduction reaction and in turn, improve NO_x conversion efficiencies. In the current study, a number of design variations of the urea-SCR system which included two mixer types and three decomposition pipe lengths, were evaluated systematically using CFD analysis and experimental measurements. The purpose of the CFD analysis was to estimate the distribution of reductant within the urea-SCR system with a specific configuration and the purpose of the engine emission test was to measure the amount of NO_x reduction, respectively. The results from the systematic analysis revealed the relation between the reductant distribution over the SCR and the performance of the NO_x reduction.     

NOx reduction characteristics of Pt-ZSM-5 catalyst with diesel engine exhaust

The platinum ion-exchanged ZSM-5 zeolite catalyst (Pt-5), which reduces nitrogen oxides (NO_x) in the presence of oxygen and hydrocarbons, was applied to actual diesel engine exhaust. Compared to the Cooper ion-exchanged ZSM-5 zeolite catalyst, the Pt-Z had higher NO_x reduction efficiency, η_NOx = 33%, and lower activation temperature, 250°C, in normal engine operation. It was found that water in the exhaust gas did not apparently affect the NO_x reduction, while the reduction efficiency was significantly affected by the aspect ratio of the catalyst reactor and by the shape of the catalyst, i.e. pellet or honeycomb.     

Study of n-C<Subscript>12</Subscript>H<Subscript>26</Subscript> reforming over DFC catalyst in a simulated diesel exhaust

In lean-DeNOX catalysis reactions, hydrogen is a good reducing agent in PGM catalysts as well as an effective promoter in selective catalytic reduction reactions over base metal oxide catalysts. However, such a lean-DeNOX system, which uses hydrogen, requires an on-board fuel reforming system applicable to internal combustion engines. In this study, catalytic partial oxidation (CPOx) performance was tested in a laboratory for various reactants and hydrocarbon conditions. Volume concentrations of 5–10% oxygen and 0-5% water vapor were used to simulate diesel exhaust, and n-C₁₂H₂₆ was used as the feedstock for the reforming reaction. In the CPOx of n-C₁₂H₂₆, the highest hydrogen selectivity was 64% and was achieved at 100,000 h-1 GHSV. Additionally, the C/O ratio was less than unity in the absence of water vapor. However, as the water concentration was increased to 2.5 and 5.0 vol. % in the n-C₁₂H₂₆ CPOx reactions, the maximum hydrogen selectivity was increased from 64% in the absence of water to 70% and 75%, respectively. This effect is a consequence of the water-gas shift reaction over the catalyst bed. Regarding oxygen concentration effects, hydrogen selectivity slightly increased with increasing oxygen concentration from 10% to 15%. It was also found that the CPOx reaction of n-C₁₂H₂₆ can be ignited at temperatures below 300 C. Accordingly, it can be concluded that CPOx is a useful and feasible device for promoting diesel DeNOx catalysis in terms of hydrogen productivity and reaction initiation.     

Simulation Study on Thermal Management Strategy to Achieve 99 % SCR Efficiency of a Heavy-Duty Diesel Engine over a Transient Cycle

In this study, NOx conversion characteristics of a urea selective catalytic reduction (SCR) system equipped on a heavy-duty diesel engine were evaluated through engine dynamometer bench tests over a scheduled world harmonized transient cycle (WHTC). Also, based on transient SCR simulations, the thermal management strategy to improve SCR NOx conversion efficiency was investigated. As a result, it was found that a selective increase in exhaust temperature at low temperature period would be a useful measure to increase SCR efficiency on WHTC mode. From the baseline SCR efficiency of around 98 % on WHTC mode, the current simulation results have shown that around 99 % level of SCR efficiency would be achievable by increasing exhaust temperatures with modifying diesel exhaust fluid (DEF) dosage. Another valuable contribution of this study is that the design guidelines for controlling exhaust temperature and DEF injection to obtain a target NOx conversion efficiency are presented for SCR systems of heavy-duty diesel engines on transient operating conditions.     

Majorization of working parameters for non-thermal plasma reactor and impact on no oxidation of diesel engine

The main target of this work is to realize the function of pre-oxidizing NO from diesel engine’s exhaust by using self-designed double-dielectric Non-thermal Plasma (NTP) reactor. The majorized discharge frequency and discharge peak to peak voltage (V_p-p) range for NTP reactor were obtained through air discharge test. The diesel engine test bench was established to observe the effect of NTP on the volume fraction of NO. The results showed that there were more active substances and fewer by-products in NTP reactor when discharge frequency was 9 kHz and V_p-p was between 9 kV and 23 kV; Exhaust flows had insignificant effect on the performance of NTP pre-oxidizing NO; The ability of NTP to pre-oxidize NO gradually weakened with the increase of engine load, and when the engine load were 0 % and 25 %, the ratio of NO/NO₂ could reach 1. In such working conditions, SCR system could improve the conversion rate of the NO_x at low-temperature zone through quick reaction combined with NTP.     

柴油机尿素 SCR 反应特性的试验研究

利用可独立控制尿素喷射量的SCR系统,通过柴油机台架试验,研究了钒基催化剂温度和空速对SCR催化还原反应NOx 转化效率和反应速率的影响,以及尿素喷嘴安装位置对转化效率的影响。结果表明：NOx 转化率随着氨氮比（NH3与NOx 物质的量之比）的升高而逐渐升高,由于尿素水解和热解不完全等因素,氨氮比上升到2时NOx 转化率才可达到最大;NOx 转化率随着催化剂温度升高而升高,到400℃时基本趋于稳定,NOx 转化率随空速升高略有下降;SCR反应速率随温度的升高而升高,随空速的变化不明显;相同氨氮比时,尿素喷嘴与催化剂的距离增加,有利于NOx 转化率的升高。     

Model-based optimization of parameters for a diesel engine SCR system

A Selective Catalytic Reduction (SCR) system simulation model for diesel engines was established based on MATLAB/Simulink. The model includes four subsystems: signal acquisition, DEF (Diesel Exhaust Fluid) dosing control, catalytic chemistry reaction and NO_X emissions reduction. The SCR control strategy was optimized based on ETC simulation results. Simulation and test results indicate that the model developed in this paper can predict ETC NO_X emissions accurately.     

满足国Ⅴ排放的重型柴油机排气后处理技术

研究了国外重型发动机在欧Ⅳ到欧Ⅴ阶段(或US2007到US2010)的技术路线,并探讨国内重型柴油机达到国Ⅴ排放可采用的排气后处理技术方案。由于柴油机排放物PM与NOx存在折中效应,为达到国Ⅴ排放标准,应采用组合式后处理技术。在各种后处理技术方案中,SCR+DOC+DPF/POC和EGR+DOC+DPF是两种主要的技术措施,而LNT+DOC+DPF技术对排气中的S特别敏感。     

Real-time empirical NO<Subscript>x</Subscript> model based on In-cylinder pressure measurements for light-duty diesel engines

This paper proposes a real-time empirical model of NO_x emissions for diesel engines. The proposed model predicts the level of NO_x emissions using an empirical model developed based on the thermal NO formation mechanism, the extended Zeldovich mechanism. Since it is difficult to consider the exact physical NO formation phenomena in real-time applications, the proposed algorithm adapts the key factors of the NO formation mechanism from the extended Zeldovich mechanism: temperature of the burned gas, concentration of the gas species, and combustion duration where NO is generated. These factors are considered in a prediction model as four parameters: exhaust gas recirculation rate (EGR rate), crank angle location of 50 % of mass fraction burned (MFB50), exhaust lambda value, and combustion acceleration. The proposed prediction model is validated with various steady engine experiments that showed a high linear correlation with the NO_x emission measured by a NO_x sensor. Furthermore, it is also validated for transient experiments.     

Comparison of fuel efficiency and exhaust emissions between the aged and new DPF systems of Euro 5 diesel passenger car

This study was conducted to examine the impact of aged and new DPF systems of the Euro 5 diesel passenger car on fuel efficiency and exhaust emissions. Test diesel vehicle used in this study was equipped with diesel oxidation catalyst (DOC) and diesel particulate filter (DPF) as aftertreatment systems, and satisfied the Euro-5 emissions standard. The displacement volume of engine was 1.6 L and the cumulative mileage was 167,068 km before the test. The FTP-75 test procedure was used, and the time resolved and weight based exhaust emissions of total hydrocarbon (THC), carbon monoxide (CO) and nitrogen oxides (NOx) were measured. The results show that the vehicle with the new DPF system has lower emissions of THC, CO and NOx than the aged one, and fuel efficiency also increased about 5 percent. The aged DPF system had higher backpressure due to the particulate matter (mostly in the form of ash) accumulated in the DPF. As was shown in the analysis using X-CT (X-ray computer tomography), the aged DPF system had particulate matter (PM) accumulated to a length of 46.6 mm. In addition, a component analysis of PM through XRF (X-ray fluorescence) analysis found that 50 % or more of the components consisted of the P, S, Ca, and Zn.