Dynamic Interaction of Railway Systems with Large Bridges

SUMMARY

In this paper have been described

- railway runability problems on large span bridges;

- the state-of-art of the methodologies adopted for a systematic analysis of the dynamic behaviour of railway vehicles running on a deformable structure, with particular reference to large span suspension bridges;

- some meaningful experimental and analytical results, related to railway runability of large span bridges.     

Railway Vehicle Active Suspensions

This paper reviews the state-of-the-art of active suspensions for use on railway vehicles. The primary focus of the paper is on ride quality control, both vertical and lateral, and on lateral stability control.

The section on theoretical considerations summarizes the results of a one-degree of freedom optimization and then investigates analytically the use of active suspensions for lateral ride and stability augmentation. It is shown that separate control structures using different measurements and actuator actions are very effective in controlling both ride quality and stability.

A section on a survey ofcurrent activities reviews published research on active railway suspension work around the world.

Finally a concluding section indicates future trends in active suspension applications.     

Critical Speed and Limit Speed in Phenomena of Lateral Instability on Railway Vehicles

A comparison between theoretical calculations on dynamic lateral behaviour of railway vehicles and experimental results shows quite a sizeable difference between the calculated critical speed and the actual speed at which side impact phenomena will repeatedly occur between wheel flange and rail (running speed limit), such impact speed being remarkably lower than calculated.

Another typical experimental aspect is that the running speed limit will considerably vary for the same vehicle depending on the test track conditions. Such difference is usually attributed to alterations of the wheel-rail contact surfaces, only.

This paper will discuss some concurrent causes which may prove far from negligible, such as the effects of track defects, an amplification of the dynamic lateral displacement between wheel and rail on approaching the critical speed, the track mechanical properties, and in particular the track lateral rigidity.

The influence of some geometrical factors typical of the wheel-rail contact, such as side clearance and linearized conicity, will also be discussed. The approach is based on the application of statistical methods to dynamic linear systems.     

新建200 km/h客货共线铁路大跨度连续刚构桥设计研究

遂渝铁路是我国第一条新建时速200 km铁路,跨越涪江和嘉陵江时采用大跨度预应力混凝土连续刚构桥。在已建成的铁路桥梁中,无论是设计行车速度、大跨桥上无缝线路设计,还是结构形式均有新的突破。介绍其结构设计,并着重对其关键技术分析进行论述。     

A Theory of Wheelset Forces for Two Point Contact Between Wheel and Rail

This paper describes a quasistatic theory of wheelset forces for an important practical case of the wheelset rolling when one of the wheels touches the rail in two contact zones. One of these zones lies on the tread and the other on the wheel flange. For such contact the specific problem of finding the distribution of forces between the tread and flange arises. The simultaneous frictional rolling contact problems for both contact zones have been described with Kalker×apos;s non-linear theory and wheelset equilibrium equations.

The numerical results presented are for an individual wheelset on straight track, the distribution of forces being described for a wide range of loading conditions. The influence of steering on the distribution of forces has also been presented.

This theory can be easily extended for quasistatic curving of railway vehicles and may assist wear studies for vehicles with worn wheels.     

Solution of the Multiple Wheel and Rail Contact Dynamic Problem

An unconventional method for calculating the forces developing in the wheel and rail contact patches of a railway vehicle has been implemented at the New Technology Laboratory of INRETS. It takes into account the elastic deformations of the materials in the Hertzian elliptical contact areas; the possibility of having simultaneously several contact patches on each wheel, is introduced in the simulation of the dynamic phenomena.

The theory is applied for a high speed bogie running on a perfectly straight track.     

Steering and Dynamic Stability of Railway Vehicles

For railway vehicles having coned wheels mounted on solid axles there is a conflict between dynamic stability and steering ability

It is shown that the stiffness and kinematic properties of all possible interwheelset connections are characterised by two properties describing the distortional characteristics of the vehicle in plan. Within this framework, the various possibilities for steered wheelsets are considered, and several past and current proposals are reviewed. Using the linear approach to dynamic stabibty and curve negotation the performance of existing and newly proposed configurations is discussed

For any symmetric, two-axle vehicle it is shown that for perfect steering on a curve there should be zero bending stiffness between the wheelsets. It is further shown that if the bending stiffness is zero, the vehicle lacks dynamic stability as the critical speed of instability, is zero. In this case, the vehicle undergoes a steering oscillation which occurs at the kinematic frequency of a single wheelset and which is a motion in which pure rolling occurs

Similar results are obtained with vehicles with three or more axles if adjacent axles are connected by shear structures. However, it is shown that it is possible to satisfy both the requirements of perfect steering and a non-zero critical speed if the vehicle has zero bending stiffness and if, in addition to adjacent wheelsets being connected in shear, at least one pair of non-adjacent axles are connected by a shear structure.     

Simulation model for the study of overhead rail current collector systems dynamics, focused on the design of a new conductor rail

Overhead rigid conductor arrangements for current collection for railway traction have some advantages compared to other, more conventional, energy supply systems. They are simple, robust and easily maintained, not to mention their flexibility as to the required height for installation, which makes them particularly suitable for use in subway infrastructures. Nevertheless, due to the increasing speeds of new vehicles running on modern subway lines, a more efficient design is required for this kind of system.

In this paper, the authors present a dynamic analysis of overhead conductor rail systems focused on the design of a new conductor profile with a dynamic behaviour superior to that of the system currently in use. This means that either an increase in running speed can be attained, which at present does not exceed 110 km/h, or an increase in the distance between the rigid catenary supports with the ensuing saving in installation costs.

This study has been carried out using simulation techniques. The ANSYS programme has been used for the finite element modelling and the SIMPACK programme for the elastic multibody systems analysis.     

Very-High-Speed Tests on the French Railway Track

The very-high-speed tests carried out by SNCF between the end of 1989 and May 1990, are an extension of the investigations which have been made for many years in order to acquire the control of high speeds. The high-speed run which ended the tests is well known [1], [2],[3].

In order to place the final test campaign in its context, we can recall progression made during the last decade.

In February 1981, the maximal speed of 380 km/h was reached with a TGV-PSE¹ train set, having the same configuration as the series, but only seven trailers instead of eight.

During the following years, until 1986, the pneumatic suspension and the new Y 231 carrying bogies designed for TGV-ATL train sets were developed, with numerous test runnings in the speed range from 300 to 350 km/h, in order to obtain certitudes as regards the stability of the bogies and the appropriate choice of anti-hunting devices for commercial speeds of 270 km/h (LGV-PSE) or 300 km/h (LGV-ATL).

These tests allowed the definition of the TGV equipment design principles, which are applied today as regards the critical speed of the bogies.

Between 1985 and 1988, the development of the prototype train set equiped with self-controlled synchronous motors (March 1988) led once more to numerous runnings at high speed, in December 1988 with the so-called “operation TGV 88”. During this operation, the speed range from 350 to 400 km/h was investigated (maximal speed 408,4 km/h on December 12th 1988).

Apart from the capability of the synchronous traction equipment to develop the required power and the performance consisting in the realization of such tests on a line kept in operation (LGV-PSE), the teachings gathered together during this test campaign were decisive for the pursuit of the operation.

On this occasion, we discovered that:

-with the single-phase GPU pantograph mounted on this train set, we could get the current collection under control without difficulties inside the studied speed range,

-the bogies presented a stability margin distinctly higher than that which had been estimated, according to the results of former experiences.

Consequently, the test campaign of the TGV 117 could be engaged with a great confidence in the capabilities of the TGV equipment to achieve markedly higher speeds with full safety. The preparation of this test campaign had begun in 1986 and was conducted in a parallel direction to the above mentioned experimentation.

The campaign was preceded by a preliminary test campaign with the train set TGV-ATL n° 308, with a reduced train composition, including eight trailers. The goal was the validation, until 390 km/ h, of the test field consisting in the TGV-ATL Aquitaine branch, as well for the track as for the overhead contact line, the achievement of which was just ended.

The operation TGV 117 was then carried out in two phases:

-in December 1989 the train set TGV-ATL 325 with a reduced train composition consisting in four trailers between two motor cars reached the maximal speed of 482,4 km/h on December 5th,

-in May 1990 the same train set, but with only three trailers, improved the performance unto the final record: the speed of 515,3 km/h was reached on May 18th.     

Railway Vehicle Modelling by the Constraint Equation Method*

A method for the dynamic analysis of railway vehicles is proposed. The method is based on both the using of constraint equations, and on the building of the mathematical model by means of the initial data.

The calculation models are nonlinear, due both to the connecting elements, and to the wheel-rail contact modelling. Solving of differential equations is achieved by time step integration. The method has been applied to the analysis of a freight wagon and a train unit.     

Dynamic Behaviour of a Mobile Robot Vehicle with a Two Caster and Two Driving Wheel Configuration

The actual trajectory covered by a mobile robot in motion differs from the trajectory planned on the basis of the kinematic characteristics of its directional control system. This difference is essentially related to the behaviour of wheel-road contact, the influence of dynamic loads and the presence of caster wheels.

This paper presents a mathematical model (“ DDPP) which simulates the motion of a generic mobile robot vehicle with a propulsion and directional control system based on two independent driving wheels and two caster wheels.

The differential equations of motion have been obtained by applying modified equations of Lagrange.

The role played by the dynamic loads, the wheel-road contact features and the caster wheels is discussed hereof.     

Determining the Characteristics of Helical Springs for Application in Suspensions of Railway Vehicles

This study concerns the theoretical calculation of the characteristics of helical springs used, particularly, for the primary and secondary suspensions of railway vehicles: the static characteristics will be determined by an exact method where as the dynamic characteristics will be determined with the help of an approximate method whose precision is, however, sufficient to make a valid evaluation of the dynamic behavior of the vehicles themselves.

The first part of the study is presented here, while a second part will appear in the next issue of “Vehicle System Dynamics”.     

Dynamic Measurements in the Research and Development of Rail Vehicles

This paper reviews the measurements which are necessary to all aspects of vehicle dynamics as applied to rail vehicles. Although an attempt has been made to introduce some reference to measurements made in Europe and America, the detailed discussion has been limited to those techniques employed by British Rail. This has the advantage that the discussion can be first hand and therefore more specific.

For convenience the measurements have been collected together under four broad headings.

1. Measurements of rail system data.

2. Measurements of vehicle parameters.

3. Measurements to validate theory and predictions.

4. Measurements of vehicle performance.     

沿海铁路温福线桥梁设计综述

由于客运专线线路标准较高,且处于沿海地区,受复杂自然条件的影响,温福铁路桥梁长联大跨弯连续梁采用较多。对温福铁路全线特殊跨度桥梁予以介绍,并对其中有代表性的桥梁设计特点进行了说明。     

Ride Quality and Dynamics of Rail Vehicle Models for Microcomputers

This paper describes mathematical and computer models for ride quality and dynamics of rail vehicles developed for running on personal computers. The purpose of the computer simulations is for prediction of ride quality in order to study the dynamic stability of the system and the effect of track quality and irregularities on ride quality.

In deriving the equations of motion for dynamic stability, the tangential forces acting on the contact areas between the wheels and rails are of fundamental importance in railway vehicles dynamics and are included in the analysis [1]. These forces are due to the creep phenomenon between the wheel and the rail on which it is rolling. Track irregularities are defined in terms of four components consisting of gauge, cross level, alignment and vertical surface profile [2]. Relation of allowable track irregularities versus speed is given by the FRA Track Safety Standards. Analytical representation of track irregularities should include both PSD (Power Spectral Density) for CWR (Continuous Welded Rail) as well as discrete inputs from track joints.

In this paper, the rail vehicle suspension analysis and dynamics mathematical and computer models are described. The computer models are written in Fortran 77 and designed to run on personal computer. The paper also discusses programming considerations that must be taken into account when programming for microcomputers under DOS (IBM's Disk Operating System) and MS or RM Fortran Compilers. Most of the considerations are however, valid in general with respect to engineering software development and programming for microcomputers.

Computer graphics is a powerful tool for visualization of the resulting solutions such as the display of the characteristic roots for the eigenvalues solution on a root locus plot and representation of acceleration levels versus the “Reduced Comfort Boundary” limits defined by the International Standards Organization” (ISO 2631-1985). In this paper some examples of these resulting outputs are presented and their significance discussed.     

Active Suspension Control; Performance Comparisons Using Control Laws Applied to a Full Vehicle Model

Based on a mathematical model of an actively suspended vehicle, the effects of the following issues in deriving the control laws are studied:

(a)representation of the ground surface as integrated or filtered white noise.

(b)cross-correlation between left and right track inputs.

(c)wheelbase time delay between front and rear inputs.

The third of these issues is shown to be by far the most important. Considerable improvements at the rear suspension can be obtained if the control law includes the information that the rear input is simply a delayed version of the front input. Effectively this provides feedforward terms in the control law for the rear actuator. For the full state feedback case, these improvements are indicated by reductions in the rear body acceleration and rear dynamic tyre load of around 20% and 40% respectively with no increase in suspension working space.     

A new method for the solution of the normal contact problem in the dynamic simulation of railway vehicles

Due to requirements related to computational efficiency, in the majority of railway dynamic simulators the Hertz theory is used for solving the normal problem in wheel/rail contact. This theory is based on a large number of assumptions. Particularly noteworthy is the assumed simplification that the undeformed distance between the bodies in contact can be assimilated by a quadratic function. There are many situations in which the undeformed distance cannot be represented by this kind of function. As such, the results obtained with Hertz theory in these cases are not accurate.

In this paper, a new method for solving the normal problem that overcomes the above-mentioned limitation is presented. First, the exactness of the new method is tested with Hertzian cases. The results obtained are almost exact. Second, the results calculated with the new method in more general cases are compared with the ones obtained with the variational method of Kalker (more exact but computationally less efficient).     

Messungen von Fahrbahn-Unebenheiten paralleler Fahrspuren und Anwendung der Ergebnisse

Measurement of two track road inputs and theoretical application of the results

The calculation of vehicle response to road-surface irregularity inputs requires the spectral densities of the left and right longitudinal track and their statistical dependence

This paper presents some resluts of parallel profile measurements, three typical german roads have been chosen

Random vibration of two vehicle types are digital-simulated. The dynamic tire load shows that independent suspension systems are more advantageous than beam axles, because by wheel tramp this type increases the dynamic tire load.     

Optimization for Vehicle Suspension II: Frequency Domain

The objective of this study is optimizing the components design of a vehicle suspension system under excitation due to road roughness. The vehicle is modelled as a dynamic system made of masses interconnected by, linear, springs and dampers. The optimizing code provides values corresponding to the caracteristics of masses, dampers and springs which, within a range, minimize the objective function for a defined excitation. This objective function auantifies the vehicle comfort level.

The optimization method used is the sequential linear programming by iteratively applying the Simplex algorithm. The model response is obtained in frequency domain and the vehicle excitation can be either random or deterministic.

The exact nature of the optimization problem, objective function and restrictions, depend on the type of excitation considered.

In succeeding paragraphs, the problem formulation together with a comparison with other authors is presented.