高压共轨燃油喷雾特性的试验研究与模型修正

利用高速闪光摄像技术建立了燃油喷雾特性试验台架,在不同喷射压力(80 MPa,102 MPa,130 MPa)和不同喷射背压(2 MPa,3 MPa)下对高压共轨电控喷油器的燃油瞬态喷雾特性进行了研究,并用Matlab编程对喷雾图像进行了处理,测量了不同工况下油束的贯穿度和锥角。通过试验数据,利用最小二乘非线性曲线拟合方法对高压喷射油束模型进行了修正,模型计算结果与试验结果基本吻合,表明修正后的油束模型能更好地预测高压喷射时的油束贯穿度和锥角。     

二甲醚／柴油混合燃料在压燃式发动机上的应用

为探索二甲醚/柴油混合燃料作为柴油机替代燃料的应用性能,对D20二甲醚/柴油混合燃料的喷雾特性进行了试验研究;同时,开展了直喷式柴油机燃用二甲醚/柴油混合燃料动力性能、经济性能及排放性能研究。结果表明:在同样的环境背压下,D20混合燃料的油束与柴油相比较,贯穿度有所缩短,喷雾锥角有所增大;柴油机燃用二甲醚/柴油混合燃料时,通过适当调整循环油量,发动机的动力性可以超过原柴油机,最低当量比油耗下降4.5%,烟度指标下降70%以上,NOx排放降低30%~50%;二甲醚/柴油混合燃料是一种能实现高比功率、低排放的石油替代燃料。     

Instantaneous 2-D visualization of spray combustion and flame luminosity of GTL and GTL-biodiesel fuel blend under quiescent ambient conditions

An experimental study has been performed on spray combustion and two-dimensional soot concentration in diesel (ULSD), GTL and GTL-biodiesel fuel jets under high-pressure, high-temperature quiescent conditions. Instantaneous images of the fuel jets were obtained with a high-speed camera. It was confirmed that by blending GTL with 20% rapeseed biodiesel, certain fuel properties such as kinematic viscosity, density, surface tension, volatility, lower heating value and others may be designed and improved to be more like those of conventional diesel fuel but with considerable decrease in the amount of sulfur, PAH, cold filter plugging point, etc. The results showed that the spray tip penetration increased and the spray cone angle decreased when 20% biodiesel fuel was added to GTL fuel. Autoignition of the GTL-biodiesel blend occurred slightly earlier than that of diesel fuel. Experiments under high-pressure, high-temperature conditions showed that higher injection pressure induced a lower soot formation rate. The integrated flame luminosity, which serves as an indicator of soot concentration in the fuel jet, was slightly higher for the GTL-biodiesel blend than for pure GTL fuel due to the slightly higher sulfur content of pure biodiesel fuel.     

柴油掺混二甲醚喷雾粒子尺寸分布特性试验研究

为确定二甲醚掺入柴油后对燃料雾化性能的改善效果,利用阴影成像与数字图像处理技术,对不同掺混比、喷射压力以及喷孔直径等条件下的二甲醚-柴油混合燃料喷雾粒子尺寸分布特性进行了对比试验研究.结果发现:由于柴油中二甲醚的闪急沸腾作用,随着二甲醚掺混比的增加,混合燃料粒子尺寸分布曲线整体向小颗粒方向偏移,较大粒子数目较柴油明显减少,有助于降低发动机炭烟排放;喷孔直径、喷射压力等喷射参数对混合燃料雾化粒子分布有较大影响,减小喷孔直径使燃油粒子更加细化,降低喷射压力则使混合燃料雾化效果有变差的趋势.     

柴油-正丁醇混合燃料的宏观喷雾特性试验研究

在高压共轨燃油喷雾试验台上对正丁醇体积掺混比分别为0%,5%,10%和20%的柴油-正丁醇混合燃料的宏观喷雾特性进行了研究。结果表明:在相同共轨压力下,随着背压的增加,喷雾锥角增大,喷雾贯穿距减小;在相同背压下,随着共轨压力的增加,喷雾贯穿距和喷雾锥角均逐渐增大,但当共轨压力增大到110 MPa时,二者不再增大;在相同背压和相同共轨压力下,喷雾贯穿距和喷雾锥角随着正丁醇比例的增加逐渐增大,说明在柴油中混合一定比例的正丁醇可以提高燃料的雾化质量。     

高压共轨柴油机喷雾特性研究

为了探究大背压环境下高压共轨柴油机的喷雾特性,研制了一种可视化喷雾系统,该系统能够实现3 MPa背压环境下的高压喷射.基于该系统,研究了不同喷射压力和背压对高压共轨柴油机喷雾特性的影响.结果表明:同一背压下,随着喷射压力的提高,喷雾锥角逐渐变大,并且存在微小的波动现象,贯穿距离也随之增长,但增长的幅度较小;同一喷射压力...     

Effect of nozzle orifice diameter on diesel spray tip penetration according to various spray models for CFD simulation with widely varying back pressure

CFD simulations of spray tip penetration with the standard KIVA3V, ‘original gas jet’ and ‘Normal gas jet profile with breakup length formula’ (NGJBL) spray models were performed to investigate the effects of nozzle orifice size and ambient gas density combinations on the spray penetration. The accuracy of the CFD simulation results was estimated by comparing them with available experimental data. The ambient gas density was varied in 12 kg/m³ intervals from 12 to 69 kg/m³ for each nozzle orifice diameter. The nozzle orifice diameters used were 119, 140, 183 and 206 mm. A total of 20 cases in the CFD simulations were considered with combinations of the 4 nozzle orifice diameters and 5 ambient gas densities. CFD simulations with the NGJBL spray model were more accurate than those with either the standard KIVA3V or gas jet spray models as the nozzle orifice diameter and ambient gas density was increased. The NGJBL and original gas jet model is more effective in predicting the spray tip penetration near the nozzle tip region.     

二甲醚发动机的燃烧与排放研究

在一台2135直喷柴油机上，对燃油供给系统进行了适当的改造，测试了燃用二甲醚发动机的燃料喷射时刻、气缸压力和有害排放，计算分析了放热规律及滞燃期变化规律。研究结果表明，在供油提前角相同的情况下，二甲醚的喷射延迟比柴油长而滞燃期比柴油短，着火时刻落后于柴油；二甲醚的最大放热速率小，而燃烧持续期短；二甲醚发动机接近无烟排放，N0x排放浓度显著低于柴油机。     

高温高压条件下柴油的雾化蒸发特性

利用高速摄影和纹影法,在可变温度和压力的定容燃烧弹中,模拟发动机的实际运转工况,进行了不同喷油压力和背景压力条件下柴油的雾化蒸发特性试验研究,得出一系列热态喷雾图像。研究表明：喷油压力越高,雾注总的贯穿距离、锥角和投影面积越大,但液核的最大贯穿距离、锥角和投影面积变化不大,显著蒸发时刻不断提前,气相部分投影面积增大,混合均匀性改善;随着背景压力的升高,气、液相贯穿距离均下降,雾注总的喷雾锥角增大,雾注面积、液核面积减小。     

转子发动机喷雾特性试验研究

利用定容弹、纹影仪以及高速相机等装置,就柴油转子发动机工况下的喷雾过程进行了试验研究,重点分析了喷雾环境背压和喷射压力对喷雾特性的影响。结果表明:在转子发动机喷雾过程中,喷雾扩散速度先快速增大后逐渐减小;喷雾锥角在初次雾化阶段内急剧减小,然后在二次雾化作用下保持相对稳定。喷雾环境背压的增大,有效减小了喷雾贯穿距离,增大了喷雾锥角,说明喷雾环境背压的增大对喷雾贯穿距离和锥角都有显著的影响,从而为转子发动机喷油正时的优化提供了试验数据支持;随着喷射压力提高,喷雾贯穿距离和喷雾锥角都增大,并且增大喷射压力加强了燃油的初次雾化和二次雾化,有利于提高转子发动机喷雾质量,为优化柴油转子发动机油气混合状态创造了条件。     

柴油机静态喷雾特性的实验研究

利用高速摄像装置和高压容器，拍摄了柴油机喷雾的逆光图像；研究了喷雾周围介质密度和种类对喷雾贯穿距离、喷雾锥角以及蒸发等喷雾特性的影响。     

不同喷射工况下的GDI喷雾模拟标定研究

准确模拟喷雾是提高缸内模拟准确性的关键,为了使模拟喷雾与试验喷雾更加一致,需要根据试验喷雾贯穿距及粒径对模拟喷雾进行标定。使用AVL FIRE软件建立定容弹及喷雾数值模型,对处于不同喷射工况(喷射压力、环境压力、油温)下的喷雾进行数值模拟,根据试验喷雾的贯穿距及喷嘴下方30 mm平面处SMD对模拟喷雾进行标定,并对不同喷射工况的标定参数选择进行探讨。结果表明:为了同时满足贯穿距和粒径的标定要求,需要根据工况参数对标定参数进行调整;对于本研究中的GDI喷油器,喷射压力10 MPa时使用KH-RT模型的模拟结果与试验值匹配较好,5 MPa时使用Huh-Gosman模型匹配更好;在喷射压力、环境压力和环境温度相同的条件下,高油温和低油温工况可以用同一套参数满足标定要求。     

利用高速摄影研究二甲基醚的喷雾特性

本文利用高速摄影技术在定容压力室中，通过6孔电磁喷射器，研究了二甲基醚（DME）的喷雾特性。结果表明，二甲基醚的喷雾射程随着定容压力室内气体压力的增加而减少；喷雾锥角则随和的升高而增大，在相同的条件下，二甲基 喷射锥角大于 喷射锥角；喷雾射程则低于柴油的喷雾射程。Hiroyasu喷雾射程的计算模型，通过适当的系数修正可以用于DME喷雾射程预测，由于DME喷雾射程和着火延迟期都比柴油短，在屐机缸内着火时刻，柴油的喷雾射程约为DME的2倍，从高速摄影的喷雾影像中可以清楚的看到，DME的蒸发速度明显比柴油快。     

正丁醇-柴油混合燃料喷雾特性的模拟研究

根据喷雾可视化试验的结果,利用三维CFD软件建立了正丁醇柴油喷雾的仿真模型,并验证了模型的准确性。利用该模型研究正丁醇柴油混合燃料的喷雾特性,模拟了喷雾的发展过程,计算了不同掺混比对喷雾贯穿距、液滴索特平均直径、速度场、密度场的影响。结果表明:模拟计算与可视化试验结果基本一致;随着正丁醇掺混比的增加,混合燃料的喷雾贯穿距和索特平均直径均降低,喷雾锥角变大,雾化特性变好。     

Effects of diesel fuel characteristics on spray and combustion in a diesel engine

Fuel properties play a dominant role in the spray, mixture formation and combustion process, and are a key to emission control and efficiency optimization. This paper deals with the influence of the fuel properties on the spray and combustion characteristics in a high-pressure and temperature chamber. Light diesel fuel spray and combustion images were taken by using a high-speed video camera and analyzed by their penetration and evaporation characteristics in comparison with current diesel fuel. Then, a single-cylinder DI engine was used to investigate combustion and exhaust characteristics. The mixture formation of the light diesel fuel is faster than that of the current fuel depending on physical properties like boiling point, density, viscosity and surface tension. Engine test results show that smoke is reduced without an increase in other emissions.     

Modeling of gasoline fuel spray penetration in SIDI engines

The paper presents a research on the fuel injection and atomization depending on the thermodynamic quantities inside the cylinder of a combustion engine. With the use of piezoelectric outward-opening injectors the changes in the geometrical quantities of the atomized fuel in the aspect of its injection were determined. The studies concerning the influence of the individual quantities on the fuel spray penetration injected by the outward-opening injectors comprise a synthesis of the injection and atomization tests. Own mathematical equation describing the fuel spray penetration was proposed. The exponents (equation coefficients) related to the influence of the fuel pressure, air backpressure, charge density and time of fuel spray development were determined with the coefficient of determination 0.9797, indicating a congruence of the experimental data with the values obtained on the basis of the mathematical equation.     

Effects of injection parameters on the spray characteristics of swirl and slit injectors using the Mie-scattering method

We investigated the effects of injection parameters such as injection pressure, ambient pressure, and ambient temperature on spray characteristics. We calculated the turbulence occurring point (t _c ), defined as the time required to generate a vortex, and the deceleration point (t _b ), defined as the time when spray penetration begins to decelerate, to elucidate the breakup mechanism of the test injectors. The spray velocity coefficient (C_v) was obtained to evaluate the spray characteristics. As the ambient pressure increases in the case of a slit injector, C_v decreases. We investigated the effects of nozzle tip shape according to injection pressure, ambient pressure, and fuel properties on spray characteristics and provide a C_v value of 0.38 for the swirl injector with a spray angle of 60° and the slit injector under atmospheric conditions. The value of C_v in the case of a slit injector was reduced by increasing the ambient pressure. Our results suggest that C_v of a swirl injector is constant regardless of changes in ambient pressure, injection pressure, and fuel properties. On the other hand, C_v of a slit injector is altered by changes in ambient pressure.     

二甲醇(DME)发动机共轨燃料系统的试验研究

针对二甲醚燃料饱和蒸气压高、黏度低、易与空气形成混合气等特性,开发了低压共轨燃油系统。主要进行了系统的总体设计、电子控制单元(ECU)的软硬件开发和在油泵台架上的试验。试验结果表明,在新开发系统的驱动下,喷油器启合及时,喷射有力,雾化效果好;并获取供油量的MAP图,实现了对喷油量和喷油定时的外触发、外同步的反馈控制。     

Study of diesel spray combustion and ignition using high-pressure fuel injection and a micro-hole nozzle with a rapid compression machine: improvement of combustion using low cetane number fuel

This study aimed to reduce NO_x and soot by creating a more homogeneous lean fuel distribution in a diesel spray using high-pressure fuel injection and a micro-hole nozzle. This injection system shortened the ignition delay, but a homogeneous lean fuel distribution in the diesel spray was not achieved. Using a lower cetane number fuel, the resulting longer ignition delay made a uniform, lean fuel distribution in the diesel spray possible with this injection system. Ignition and combustion were analyzed by the combustion chamber pressure history, and flame temperatures and KL values were analyzed by the two-color method.     

喷油策略对柴油机燃烧噪声及排放影响的模拟研究

进行了通过优化高压共轨系统燃油喷射策略来改善缸内燃烧排放性能的研究,基于AVL Fire软件,针对1015柴油机开展了不同燃油喷射策略下的喷雾燃烧和排放的数值模拟,建立了数学模型并验证了模型的可靠性,分析了一次预喷的预喷时刻、预喷量、主喷提前角对燃烧噪声及排放的影响,揭示了各参数对燃烧噪声和NOx及炭烟生成的影响机理,为进一步优化预喷方案提供了理论依据。