Impact of passing-climbing lanes on traffic flow on upgrades

This study evaluates a new approach for reducing delay, and consequently improving level of service and safety on long upgrades on two-lane rural roads. This is the systematic provision of overtaking lanes, termed passing-climbing lanes (PCL), to improve traffic flow, safety, and capacity. The traffic impact of such lanes is analyzed for various grades, traffic volumes, and lane configurations by means of a simulation model developed for this study. Results show that this concept could provide substantial flow benefits—reduction in delay and in passenger-car platooning—with implications for better safety. Although the reduction in delay is found to be more pronounced as volume increases, these results may be obtained even with a small percentage of passing-climbing lanes. A model predicting average relative delay, formulated and calibrated on the basis of the simulation output, explains 95% of the observed variability. The economic advantages of the concept in optimizing the distribution of a limited budget among several sites, in staging construction over several years, and in adapting highway investment to traffic-demand variations are also discussed.     

Modeling the effect of electric vehicle adoption on pedestrian traffic safety: An agent-based approach

When operated at low speeds, electric and hybrid vehicles have created pedestrian safety concerns in congested areas of various city centers, because these vehicles have relatively silent engines compared to those of internal combustion engine vehicles, resulting in safety issues for pedestrians and cyclists due to the lack of engine noise to warn them of an oncoming electric or hybrid vehicle. However, the driver behavior characteristics have also been considered in many studies, and the high end-prices of electric vehicles indicate that electric vehicle drivers tend to have a higher prosperity index and are more likely to receive a better education, making them more alert while driving and more likely to obey traffic rules. In this paper, the positive and negative factors associated with electric vehicle adoption and the subsequent effects on pedestrian traffic safety are investigated using an agent-based modeling approach, in which a traffic micro-simulation of a real intersection is simulated in 3D using AnyLogic software. First, the interacting agents and dynamic parameters are defined in the agent-based model. Next, a 3D intersection environment is created to integrate the agent-based model into a visual simulation, where the simulation records the number of near-crashes occurring in certain pedestrian crossings throughout the virtual time duration of a year. A sensitivity analysis is also carried out with 9000 subsequent simulations performed in a supercomputer to account for the variation in dynamic parameters (ambient sound level, vehicle sound level, and ambient illumination). According to the analysis, electric vehicles have a 30% higher pedestrian traffic safety risk than internal combustion engine vehicles under high ambient sound levels. At low ambient sound levels, however, electric vehicles have only a 10% higher safety risk for pedestrians. Low levels of ambient illumination also increase the number of pedestrians involved in near-crashes for both electric vehicles and combustion engine vehicles.     

Towards an understanding of adaptive cruise control

Adaptive cruise control (ACC) provides assistance to the driver in the task of longitudinal control of their vehicle during motorway driving. The system controls the accelerator, engine powertrain and vehicle brakes to maintain a desired time-gap to the vehicle ahead. This research describes the results of a detailed microscopic simulation investigation into the potential impacts of ACC on motorway driving. In addition to simulation, real vehicle driving profiles, obtained from instrumented vehicle experiments in three European countries, have been used to compare real following behaviour with that of a simulated ACC equipped vehicle. This new approach has shown that following with an ACC system can provide considerable reductions in the variation of acceleration compared to manual driving. This indicates a potential comfort gain for the driver and environmental benefits. A number of critical situations in which ACC does not perform well have also been identified. The research also highlights the limitations of microscopic simulation in modelling the impacts of ACC because of the lack of understanding of the interaction between the driver and the ACC system relative to the traffic conditions.     

Impact of heavy vehicles on surrounding traffic characteristics

This work examines the impact of heavy vehicle movements on measured traffic characteristics in detail. Although the number of heavy vehicles within the traffic stream is only a small percentage, their impact is prominent. Heavy vehicles impose physical and psychological effects on surrounding traffic flow because of their length and size (physical) and acceleration/deceleration (operational) characteristics. The objective of this work is to investigate the differences in traffic characteristics in the vicinity of heavy vehicles and passenger cars. The analysis focuses on heavy traffic conditions (level of service E) using a trajectory data of highway I‐80 in California. The results show that larger front and rear space gaps exist for heavy vehicles compared with passenger cars. This may be because of the limitations in manoeuvrability of heavy vehicles and the safety concerns of the rear vehicle drivers, respectively. In addition, heavy vehicle drivers mainly keep a constant speed and do not change their speed frequently. This work also examines the impact of heavy vehicles on their surrounding traffic in terms of average travel time and number of lane changing manoeuvres using Advanced Interactive Microscopic Simulator for Urban and Non‐Urban Networks (AIMSUN) microscopic traffic simulation package. According to the results, the average travel time increases when proportion of heavy vehicles rises in each lane. To reflect the impact of heavy vehicles on average travel time, a term related to heavy vehicle percentage is introduced into two different travel time equations, Bureau of Public Roads and Akçelik's travel time equations. The results show that using an exclusive term for heavy vehicles can better estimate the travel times for more than 10%. Finally, number of passenger car lane changing manoeuvres per lane will be more frequent when more heavy vehicles exist in that lane. The influence of heavy vehicles on the number of passenger car lane changing is intensified in higher traffic densities and higher percentage of heavy vehicles. Large numbers of lane changing manoeuvres can increase the number of traffic accidents and potentially reduce traffic safety. The results show an increase of 5% in the likelihood of accidents, when percentage of heavy vehicles increases to 30% of total traffic. Copyright © 2014 John Wiley & Sons, Ltd.     

基于元胞自动机的双车道变道交通流特性研究

在庞杂的城市交通环境下,驾驶员为了寻求更快的速度,常常采用主动的换道行为。由于汽车使用量逐年增长,换道引起的交通事故经常发生。研究车辆变道行为,寻求有效措施减少交通事故的发生,对提高道路安全性具有积极的意义。本文以多车道系统中车辆变道行为为研究对象,以元胞自动机理论为基础,对比分析单向单车道、单向双车道换道行为,并运用MATLAB仿真软件进行分析,获得变道交通流的相关特性曲线。     

Passing Bays for Slow Moving Vehicles on Rural Two‐lane Roads

Abstract

Slow‐moving vehicles, including agricultural vehicles, on arterial highways can cause serious delays to other traffic as well as posing an extra safety risk. This paper elaborates on a small‐scale solution for these problems: the passing bay. It investigates the impacts of a passing bay on the total delay for other motorized vehicles, the number of passing manoeuvres and hindered vehicles, and the mean delay per hindered vehicle. The latter is also considered to be an indicator for traffic safety. The calculations are performed for two characteristic trips with a slow‐moving vehicle. The passing bay is an effective solution to reducing delays on arterial highways when two‐way hourly volumes exceed 600–1000 vehicles. The effects depend on the trip length and speed of the slow‐moving vehicle, and on the passing sight distance limitations of the road. A distance of 2–4?km between the passing bays seems an acceptable compromise between the reduction of delay for other motorized vehicles and the extra discomfort and delay for drivers of slow‐moving vehicles. This result also shows that passing bays are not effective in regions where slow‐moving vehicles mainly make trips shorter than this distance.     

Developing freeway lane‐changing support systems using artificial neural networks

Lane‐changing involves many concerns about safety and efficiency which makes it one of the most difficult tasks of driving. It is indeed quite personal since drivers operate vehicles according to their integrated perception of comprehensive circumstances rather than individual rules. A lane‐changing decision support model is developed in this study using artificial neural networks (ANN). The advantages of the ANN approach lie in the learning capability. Due to its nature, an ANN model can consolidate various kinds of information surrounding the vehicle for the drivers and generate reliable results to help control vehicles. It then becomes a useful mechanism to assist drivers in judging current situations and making the right decisions. Several preliminary validations and comparisons are conducted with the field survey data. It is confirmed that the ANN model mimics traffic characteristics more accurately than conventional methods. This product would expedite the implementation of relevant applications in the intelligent transportation systems context. In particular, the ANN model can be adapted to individual driver characteristics. This reveals practical feasibility and significant market potential for customized in‐vehicle equipment.     

A behavioural approach to the measurement of motorway circulation comfort and safety

The paper presents a method for measuring motorway circulation comfort and safety, based on the determination of the risk and stress levels characterizing the various choices made by drivers on the road. The method was worked out by analysing the distributions of the angular speeds with which the eye of each driver subtends the preceding vehicle width. The data used were taken from 155,000 vehicle passages over two sections of two-lane, divided carriageway motorways of identical geometric characteristics. The analysis suggested that the drivers passing over a motorway section can find themselves in three different states, which we shall term A, B and C, each having its own domain of driving alternatives. State A includes those drivers whose behaviour is not influenced by other vehicles present on the carriageway; state B encompasses those drivers whose behaviour is not influenced by the vehicles preceding them on the same lane, but by those that are following them; state C comprises those whose behaviour is affected by the vehicle preceding them on the same lane. Drivers in state C can be further divided into two groups: those, called C1, who accept the speed of the preceding vehicle and place themselves at a distance from him sufficiently large not to perceive the random fluctaution of relative speed and those, called C2, who do not accept the preceding vehicle speed and, waiting to overtake, approach him at a distance well below that of the C1 drivers so as to prevent the insertion of any changing lane vehicle and, contemporaneously, making their presence felt to the preceding vehicle. Drivers C2 because of the relative speed fluctuations receive a sequence of stimuli to which they react, also unconsciously, with a sequence of accelerations and decelerations. In this way their type of driving is risky and stressing. The authors propose the proportion s of all the drivers not in state C2 to be used as a measure of comfort and safety. The paper discusses and demonstrates how the proportion of drivers in the different states can be estimated; it also investigates the relationship existing between the measure s and the flow rate Q for various flow and time of day conditions. Furthermore the quality of circulation measure ξ₁ defined by the same authors in a preceding paper is shown to be strongly correlated with s.     

Sight distance analysis of highways using GIS tools

Analyzing the distance visible to a driver on the highway is important for traffic safety, especially in maneuvers such as emergency stops, when passing another vehicle or when vehicles cross at intersections. This analysis is necessary not only in the design phase of highways, but also when they are in service. For its use in this last phase, a procedure supported by a Geographic Information System (GIS) has been implemented that determines the highway distances visible to the driver. The use of a GIS allows the sight distance analysis to be integrated with other analyses related to traffic safety, such as crash and design consistency analyses. In this way, more complete analyses could be made and costs shared. Additionally, with the procedure proposed it is possible to use data regarding the trajectory of a vehicle obtained on a highway with a Global Positioning System (GPS) device. This application is very useful when highway design data are not available. The procedure developed and its application in a case study are presented in this article.     

振动减速带的速度控制效果研究

车速是影响道路交通安全的一个重要因素,提高速度控制技术的功效,对于改善道路安全性具有重要的意义。文章通过对振动减速带的车辆速度进行观测和分析,评价了速度控制设施的减速效果。     

Geometric design safety estimation based on tire–road side friction

A closed-loop drive–vehicle–road–environment system (DVRES) model was established using Adams/Car and Matlab/Simulink. Dynamic responses of lateral tire forces based on tire–road side friction and road geometric characteristics are used to investigate vehicle side slip for geometric design safety estimation. The root mean square, the maximum values of lateral tire forces, comfort limit on curves and vehicle trajectories are used to quantify the safety margin of side friction. The simulation results show that the safety margins of lateral tire forces for radius, operating speed and superelevation rate were 18.2%, 19.3% and 17.6%, respectively, to guarantee good vehicle lateral reliability and ride comfort, while lower speeds are optimal in wet and slippery roads. Finally, a case study was conducted to illustrate the analysis of road design safety, and on-site experiment testing further validated the accuracy and reliability of the closed-loop DVRES model.     

Deployment of interurban ATT test scenarios (DIATS): Implications for the European road network

The paper summarizes the research results and implications from the DGVII-funded Fourth Framework research project Deployment of Interurban ATT Test Scenarios (DIATS). The objective of DIATS was to identify options available in the short and medium terms, for implementing advanced transport telematics (ATT) systems for motorway-type roads and to develop scenarios of 'highest potential impact' for each of the systems identified. Included are the results of a Delphi study into the most likely deployment scenarios for ATT technologies. The methodology developed to assess the organizational, social, environmental, efficiency, safety and legal concerns associated with new ATT systems is then described. This includes stated preference questionnaires, traffic simulation modelling, driver behaviour assessment using an instrumented vehicle, analysis of accident databases and literature reviews. A multicriteria analysis of the impacts of a range of ATT systems is then presented. In particular, the results discuss the potential impacts of new in-vehicle driver assistance devices such as adaptive cruise control on the operation and effectiveness of existing fixed-infrastructure systems. The paper concludes with a prioritized list of deployment strategies of maximum impact for all of the systems assessed. The research findings are already being applied nationally and a number of field trial assessments that will assist in this are also proposed.     

Dynamic considerations of speed control humps

The objective of this study is to investigate the effects of hump parameters (cross section, dimensions, spacing, etc.) on the dynamic behaviour of the vehicle and the driver. Vehicle safety and driver comfort are most important in evaluating the effectiveness of speed control humps. A mathematical model representing the vehicle and the driver is developed. Several hump profiles are tried. A “basic” hump is selected and the effects of the individual parameters of the hump on the dynamic response of the system are evaluated through the computer simulation. The results are analysed, conclusions and recommendations for the design of speed control humps are specified.     

Queuing simulation of roadside survey station: Blocked traffic lane

External station travel surveys provide critical inputs to travel demand models. The results from these models are frequently used for statewide planning purposes. Although a roadside survey is very effective in obtaining useful information from road users, its major drawback is the excessive delay that is imposed onto road users particularly on high-volume facilities. In this paper, we used a discrete event simulation to model a blocked traffic lane survey, which is usually conducted for two-lane undivided highways. This type of survey station requires a complete stop of all oncoming traffic. Non-surveyed traffic has no ability to go around and thus has to wait in a queue in order to proceed through the survey station. Road users’ impacts are quantified in terms of delay and queue length while the performance of surveyors is measured by the number of surveys completed per unit time. Sensitivity analyses of simulation inputs reveal that simulation results are fairly insensitive to selected parameters. The results in this study provide a quick and useful guideline that roadside surveyors can use to estimate the road user impacts prior to the survey and to plan the survey procedure accordingly.     

Modelling acceleration decisions in traffic streams with weak lane discipline: A latent leader approach

Acceleration is an important driving manoeuvre that has been modelled for decades as a critical element of the microscopic traffic simulation tools. The state-of-the art acceleration models have however primarily focused on lane based traffic. In lane based traffic, every driver has a single distinct lead vehicle in the front and the acceleration of the driver is typically modelled as a function of the relative speed, position and/or type of the corresponding leader. On the contrary, in a traffic stream with weak lane discipline, the subject driver may have multiple vehicles in the front. The subject driver is therefore subjected to multiple sources of stimulus for acceleration and reacts to the stimulus from the governing leader. However, only the applied accelerations are observed in the trajectory data, and the governing leader is unobserved or latent. The state-of-the-art models therefore cannot be directly applied to traffic streams with weak lane discipline.This prompts the current research where we present a latent leader acceleration model. The model has two components: a random utility based dynamic class membership model (latent leader component) and a class-specific acceleration model (acceleration component). The parameters of the model have been calibrated using detailed trajectory data collected from Dhaka, Bangladesh. Results indicate that the probability of a given front vehicle of being the governing leader can depend on the type of the lead vehicle and the extent of lateral overlap with the subject driver. The estimation results are compared against a simpler acceleration model (where the leader is determined deterministically) and a significant improvement in the goodness-of-fit is observed. The proposed models, when implemented in microscopic traffic simulation tools, are expected to result more realistic representation of traffic streams with weak lane discipline.     

Modeling chain collisions in vehicular networks with variable penetration rates

The vehicular ad hoc network has great potential in improving traffic safety. One of the most important and interesting issues in the research community is the safety evaluation with limited penetration rates of vehicles equipped with inter-vehicular communications. In this paper, a stochastic model is proposed for analyzing the vehicle chain collisions. It takes into account the influences of different penetration rates, the stochastic nature of inter-vehicular distance distribution, and the different kinematic parameters related to driver and vehicle. The usability and accuracy of this model is tested and proved by comparative experiments with Monte Carlo simulations. The collision outcomes of a platoon in different penetration rates and traffic scenarios are also analyzed based on this model. These results are useful to provide theoretical insights into the safety control of a heterogeneous platoon.     

A microscopic analysis of speed deviation impacts on lane-changing behavior

Driving behavior models that capture drivers’ tactical maneuvering decisions in different traffic conditions are essential to microscopic traffic simulation systems. This paper focuses on a parameter that has a great impact on road users’ aggressive overtaking maneuvers and directly affects lane-changing models (an integral part of microscopic traffic simulation models), namely, speed deviation. The objective of this research is to investigate the impacts of speed deviation in terms of performance measures (delay time, network mean speed, and travel time duration) and the number of lane-change maneuvers using the Aimsun traffic simulator. Following calibration of the model for a section of urban highway in Tehran, this paper explores the sensitivity of lane-changing maneuvers during different speed deviations by conducting two types of test. Simulation results show that, by decreasing speed deviation, the number of lane changes reduces remarkably and so network safety increases, thus reducing travel time due to an increase in network mean speed.     

Agricultural vehicles and sustainable safe road traffic: solving conflicts on arterial highways

Addressing the issues of traffic safety in rural areas presents a constant challenge. The mix of light and heavy vehicles and the considerable differences in speed among these traffic participants result in high risks and delays for the faster vehicles. Agricultural vehicles (AVs) in particular have such an impact on traffic, especially when using arterial highways. This paper reviews the problems of safety and delays that AVs cause on arterial highways, and the appropriate mitigation. The concept of 'sustainable safety' in The Netherlands focuses on these problems, because of the proposed construction of parallel roads alongside all arterial highways. However, Dutch accident statistics cannot justify the high costs for the construction of parallel roads alongside 7000 km of arterial highways. Delays experienced by fast traffic are another reason for separating AVs from other road users with parallel roads. Alternative measures alongside the arterial highway, such as passing bays, restricting AVs to travelling at off-peak only and improving the conspicuity of the AVs, may be more cost-effective ways of reducing delays and/or improving traffic safety on arterial highways. Another solution may be to eliminate the need for AVs to use the arterial highway by altering their routes. For this purpose, land reallocation projects (as practised in Holland) can provide a useful tool.     

Emission evaluation of inter-vehicle safety warning information systems

Driver inattentiveness is one of critical factors contributing to vehicle crashes. The inter-vehicle safety warning information system (ISWS) is a technology to enhance driver attentiveness by providing warning messages about upcoming hazards using connected vehicle environments. A novel feature of the proposed ISWS is its ability to detect hazardous driving events, such as abrupt accelerations and lane changes, which are defined as moving hazards with a higher potential of causing crashes. This study evaluated the effectiveness of the ISWS in reducing vehicle emissions and its potential for traffic congestion mitigation. This study included a field experiment that documented actual vehicle maneuvering patterns for abrupt accelerations and lane changes, which were used for more realistic simulation evaluations, in addition to normal accelerations and lane changes. Probe vehicles equipped with customized on-board units consisting of a global positioning system (GPS) device, accelerometer, and gyro sensor were used to obtain the vehicle maneuvering data. A microscopic simulator, VISSIM, was used to simulate a driver’s responsive behavior when warning messages were delivered. A motor vehicle emission simulator (MOVES) was then used to estimate vehicle emissions. The results show that reduction in vehicle emissions increased when the ISWS’s market penetration rate (MPR) and the congestion level of the traffic conditions increased. The maximum CO and CO₂ emission reductions achieved were approximately 6% and 7%, respectively, under LOS D traffic conditions. The outcomes of this study can be valuable for deriving smarter operational strategies for ISWS to account for environmental impacts.