Cyclic behavior and strain energy-based fatigue damage analysis of mooring chains high strength steel

This study investigates the low-cycle fatigue behavior of mooring chains high-strength steel grade R4 under different strain amplitudes and strain ratios at room temperature. A fatigue test program has been carried out on small low cycle fatigue specimens cut from large mooring chains. The experimental results characterize the cyclic stress-strain relationship, the mean stress relaxation behavior, and the cyclic plasticity parameters of the material. Strain energy density is correlated with fatigue life through a simple power-law expression and very well represented by Basquin-Coffin-Mansion relationship. Further, a non-linear elastic-plastic material model is calibrated to the experimental stress-strain curves and used for the estimation of energy dissipation in the specimens under applied cyclic loads. The predicted fatigue life using the calibrated material parameters demonstrates a close agreement with the experimental fatigue life. Numerical simulations are carried out to analyze local plastic straining and assess crack initiation at the pit site of corroded mooring chains considering the multiaxial stress state. An energy-based approach is employed to estimate the number of cycles needed for a crack to initiate from an existing corrosion pit.     

Fatigue life prediction of welded stiffened 350WT steel plates

The propagation of fatigue cracks under constant amplitude cyclic loading was studied in welded stiffened steel plates. The residual stresses in the stiffened plates were measured using the neutron diffraction strain-scanning technique. A finite element model of the stiffened plate was constructed to simulate the residual stresses by an uncoupled thermal and thermo-mechanical analysis. Both the finite element model and the neutron diffraction measurements indicated that in general the residual stresses were tensile near the welded stiffeners and compressive between the stiffeners and ahead of the starter notch tip. Fatigue testing indicated that the fatigue crack growth rates of the stiffened plates were in general lower than that of a corresponding unstiffened plate, especially near the notch tip where compressive residual stresses existed. Both the finite element method and Green's function predicted the fatigue crack growth rates with reasonable accuracy.     

高强度钛合金深潜器载人舱在三种不同类型载荷下的裂纹扩展预报

随着安全性要求的提高,深潜器耐压舱的疲劳寿命评估变得越来越重要。对于耐压舱,在其服役期间经历的载荷历程包括扰动疲劳载荷和相对稳定的蠕变载荷,目前尚未有公认合适的模型来描述这一载荷谱历程。传统疲劳寿命预报方法通常忽略蠕变效应导致疲劳寿命预测较大的不确定性。为了更清楚地理解这一机理,该文对深潜器耐压舱用β-退火钛合金TC4 ELI的裂纹扩展率进行了理论分析,分别引入了三种类型载荷作用下的裂纹扩展率模型。并开展了在包含过载和保载载荷的一系列循环三角载荷下的疲劳裂纹扩展试验,对理论模型进行了验证,为合理评估深海载人潜水器的疲劳寿命提供了基础。     

07MnNiCrMoVDR钢在硫化氢溶液中的腐蚀疲劳裂纹扩展速率数学模型

本文通过试验研究07MnNiCrMoVDR钢在硫化氢水溶液中的腐蚀疲劳裂纹扩展特性,根据试验数据,利用神经网络,以介质浓度、载荷频率、应力比作为输入节点,裂纹扩展速率系数C作为输出节点,训练该网络预测不同条件下的裂纹扩展速率.根据由神经网络所预测的数据找出这三个影响因素在裂纹扩展速率系数C中的关系表达式,从而回归出07MnNiCrMoVDR钢在硫化氢水溶液中的腐蚀疲劳裂纹扩展速率数学模型.     

Remaining fatigue life assessment of corroded mooring chains using crack growth modelling

Failures caused by the combined actions of fatigue, corrosion and wear are important safety concerns for mooring chains used on floating structures in the oil and gas industry. Prediction of remaining corrosion fatigue life based on surface condition could therefore be a useful tool for the continued safe operation of corroded chains. This paper investigates the use of crack growth modelling for estimating the remaining corrosion fatigue life of mooring chains that exhibit significant pitting corrosion damage. A crack growth modelling approach is used to produce remaining fatigue life estimates for a selection of severely pitted mooring chains. Using fatigue crack growth rate test results for grade R4 high strength mooring chain steel, empirical crack growth laws are presented for free corrosion and cathodic protection conditions at load ratio R = 0.1. Two different methods for establishing equivalent cracks from surface scans of corrosion damage are presented. The mooring chains are proof loaded as part of their manufacturing process. Residual stresses introduced during this process have therefore been determined by finite element analysis and accounted for in the fatigue crack growth predictions. One of the equivalent crack models, accounting for the single dominant corrosion pit, provided quite accurate fatigue life predictions when compared with full scale test results.     

有效应力强度因子幅值计算模型的验证

裂纹闭合效应在金属疲劳中有着十分重要的作用,裂纹闭合概念已经用于解释变幅载荷作用下的裂纹扩展问题,已提出了许多基于裂纹闭合概念的有效应力强度因子计算模型.黄等人在Newman模型的基础上,提出了考虑因素更全面且便于应用的有效应力强度因子幅计算模型以及变幅载荷下工程结构疲劳寿命预测模型.为了验证该模型对不同材料的有效性和适应性,收集了一些相关的试验数据,和该模型的预测结果对比发现该模型的预测结果和试验数据符合得很好.对几种钢、铝合金和钛合金材料在不同应力比下的裂纹扩展速率数据用该模型转换成用有效应力强度因子表示的裂纹扩展速率,结果表明由有效应力强度因子幅表示的扩展速率将不同应力比下较分散的裂纹扩展率数据集中在一个很小的分散带内,同时得到了有参考价值的的一些结论.     

Crack growth direction effects on corrosion-fatigue behaviour of offshore wind turbine steel weldments

In this study corrosion-fatigue tests have been conducted on fracture mechanics specimens extracted from an S355 G10+M structural steel welded plate. The tests have been performed on compact tension specimens with the crack tip located in the heat affected zone. The corrosion-fatigue test results from this study have been compared with the data available on the base metal as well as air tests on the same material. Moreover, the obtained results have been compared with the corrosion-fatigue data available in the literature on a wide range of steels and also the fatigue trends for welded joints in free-corrosion condition recommended in the BS7910 Standard. The effect of the specimen orientation, with respect to the weld region, is also examined in this study and it has been found that higher corrosion-fatigue crack growth rates are generally observed in the tests with 0° orientation. The results have also shown that the corrosive environment has significant effects on the fatigue crack growth acceleration at the beginning of the tests; however, as the crack propagates, the environmental damage effect on crack growth behaviour becomes less pronounced. The results presented in this study are discussed in terms of improvement in the structural integrity assessment of offshore wind turbine monopiles.     

Numerical simulation of fatigue crack propagation under superimposed stress histories containing different frequency components with several mean stress conditions

Fatigue crack propagation behavior under superimposed stress histories containing different frequency components with several mean stress conditions was investigated. Numerical simulation of fatigue crack propagation based on an advanced fracture mechanics approach using the RPG (Re-tensile Plastic zone Generating) stress criterion for fatigue crack propagation was improved to extract the effective part from the applied stress history for fatigue crack propagation. The parameter, which is based on the plastic hysteresis energy consumed in the vicinity of a crack tip, was applied and implemented into the numerical simulation code of fatigue crack propagation. Fatigue crack propagation tests under various superimposed stress conditions with several mean stress conditions were performed and compared with the fatigue crack propagation histories obtained from the improved numerical simulations. These comparisons show the validity of the proposed procedure for extracting the effective stress history from the superimposed stress histories with different frequency components and mean stresses. Additionally, practical fatigue strength evaluations based on the linear cumulative fatigue damage parameter were conducted to investigate the tendency of the fatigue damage value under these stress conditions.     

压力容器接管区应变分布模拟试样(ECT)的低周疲劳裂纹扩展

设计了一种含局部减薄半椭圆缺口的紧凑拉伸试样(ECT),以模拟压力容器接管区结构,并对16MnR钢的ECT试样进行了不同应力比的恒幅低周疲劳裂纹扩展试验.结果表明:ECT试样具有类似压力容器接管区的高应变分布场;低周疲劳裂纹扩展速率与由线积分定义计算的循环J积分,△J在双对数坐标中呈良好线性相关,且回归的材料参数与相同材质的高周疲劳试验获得的Paris常数基本一致.     

不同腐蚀修正方式对LNG船疲劳强度评估的影响

船舶航行于江河湖海且装载各种货物,这决定了其构件常常承受交变载荷和腐蚀环境的共同作用,进行疲劳强度评估时必须对腐蚀介质的影响加以考虑。依据中国船级社2013年版《船体结构强度指南》,对某LNG船底边舱折角的节点疲劳强度进行了计算,分别采用腐蚀修正系数,腐蚀条件下S-N曲线和扣除腐蚀余量等三种修正方式来考虑腐蚀对疲劳强度评估的影响。研究表明,采用腐蚀条件下S-N曲线方法校核最为苛刻,扣除腐蚀余量1.5mm的结果和腐蚀修正系数1.08的结果接近。     

一种基于累积损伤理论和裂纹尖端弹塑性应力场的裂纹扩展预测方法

文章提出了一种预测疲劳寿命的应力循环叠加和损伤循环叠加的双重叠加方法。该方法依据累积损伤理论,通过分析变幅载荷下裂纹尖端的应力场,采用应力循环叠加的方法反映残余应力的影响;同时利用SWT应力应变和寿命的关系,循环叠加裂尖损伤。该方法能够很好地反映过载时裂纹扩展的迟滞效应,适合变幅载荷下疲劳寿命的评估分析。     

具初始裂纹钢桥梁焊接构件疲劳裂纹扩展和疲劳寿命计算

钢桥梁构件因焊接缺陷或者在疲劳应力交互作用下萌生裂纹,钢桥梁构件因存在初始裂纹大大地降低焊接构件的疲劳性能.文中考虑到焊接构件往往会存在初始缺陷,研究了含初始缺陷的桥梁焊接构件的疲劳分析方法.在已有的大量含裂纹构件的疲劳实验工作基础上,结合课题组所做的焊接构件疲劳实验资料,假设初始裂纹焊接构件在疲劳裂纹扩展过程中裂纹形状保持为半椭圆形状;针对桥梁构件实际受力特征,由钢桥梁构件的高周疲劳损伤演化方程入手,考虑初始裂纹条件下裂纹前缘的损伤区的存在及其对裂纹扩展的影响,采用虚拟裂纹扩张方法推导了适用于钢桥梁构件的疲劳裂纹扩展分析的疲劳裂纹扩展率公式,建议了裂纹扩展和疲劳寿命数值计算方法.采用文中的计算方法,研究了已有的钢桥梁结构焊接构件疲劳实验的裂纹扩展过程和疲劳寿命的计算.计算结果表明:裂纹的扩展过程中裂纹的深度和表面半长度之比a/c是一个变化的数值,且在一定的a0/t0条件下,随着a0/c0的增加,循环次数逐渐增大.     

A computational approach for fatigue crack propagation in ship structures under random sequence of clustered loading

The authors have developed a simulation program, CP-System, for multiple cracks propagating in a three-dimensional stiffened panel structure, where through-the-thickness crack propagation is formulated as a two-dimensional in-plane problem, and the crack propagation behavior is simulated by step-by-step finite element analyses. In order to evaluate the fatigue lives of marine structures accurately, it is necessary to take into account the load histories induced by sea waves, which may be composed of a random sequence of certain clustered loads with variable stress range. In the proposed crack growth model, the crack opening and closure behavior is simulated by using the modified strip yielding model, and the effective tensile plastic stress intensity range, ΔK _RP, is calculated by considering the contact of plastic wake along the crack surfaces. The adequacy of the proposed crack growth model is examined by comparison with fatigue tests under non-constant-amplitude loading. The usefulness of the developed method is demonstrated for a ship structural detail under certain simulated load sequences. It is shown that the fatigue crack growth of a ship structure is significantly retarded due to the load interaction effects, so that the conventional method for fatigue life assessment may predict a relatively conservative fatigue life of a structure.     

钛合金疲劳裂纹扩展速率试验及预报方法

本文针对深海载人潜水器耐压壳用钛合金,开展疲劳性能试验研究,得到该类型钛合金的室温断裂韧性,载荷比R=0.1下的疲劳裂纹扩展门槛值及疲劳裂纹扩展速率,基于选用的疲劳裂纹扩展预报模型,对载荷比R=0.1下的钛合金疲劳裂纹扩展行为进行了预报研究。结果表明:在载荷比不变的前提下,应力强度因子范围是疲劳裂纹扩展速率的主要影响因素,应力强度因子范围的增加会导致疲劳裂纹扩展速率增加;考虑小裂纹效应的疲劳裂纹扩展预报模型可对钛合金的疲劳裂纹扩展行为进行准确预报。     

钛合金疲劳小裂纹扩展行为预报方法研究

针对小裂纹扩展阶段裂纹尖端塑性区域尺寸相对于小裂纹长度是不可忽略的问题,在考虑小裂纹效应裂纹扩展速率修正模型基础上,对该模型中裂纹尺寸进行修正,即裂纹长度等于真实裂纹长度加上平面应变状态下裂纹尖端塑性区域一半;并利用修正后的模型对钛合金材料不同情况下疲劳小裂纹扩展速率和寿命进行预报,同时将预报结果与试验值比较.结果表明:修正后的预报模型对小裂纹扩展速率和寿命均有很好的预报效果.     

深海超高压环境模拟容器裂纹评定

深海超高压环境模拟容器用于模拟水下压力环境,其容器壁上承受反复载荷,容易产生疲劳裂纹.疲劳裂纹扩展是影响其断裂的主要因素.本文旨在分析半椭圆裂纹在老化的深海超高压环境模拟容器中的扩展行为,评估容器的安全性,因此对材料20MnMoNb钢的裂纹扩展特性进行了试验研究,首先考虑三角形和梯形加载情况,通过比较两组实验结果,考察了其材料对保载时间的敏感性.采用基于统一的裂纹扩展率模型的三维有限元方法进行了疲劳裂纹扩展计算,并通过CT试样的一组数值和实验结果进行了验证,最后建立了不同初始尺寸、展弦比和倾角的裂纹有限元模型,并根据裂纹在容器内壁的容许深度准则,计算了容器的剩余寿命.其分析结果可为深海超高压环境模拟容器可靠性评估提供参考.     

复杂载荷作用下潜艇结构疲劳裂纹扩展预报方法

统一疲劳裂纹扩展模型是课题组在McEvily模型基础上提出来的,它将疲劳裂纹扩展的3个扩展区域统一起来,并能解释更多的疲劳试验现象.本文介绍了统一疲劳裂纹扩展模型的基本表达式.将此模型与焊缝焊趾表面裂纹应力强度因子的计算方法结合起来,探讨复杂载荷作用下潜艇结构疲劳裂纹扩展预报方法.将服从Weibull分布的随机载荷系列编排为升序、降序载荷谱及随机载荷谱,预报潜艇锥柱结合壳焊缝焊趾处表面裂纹在3种载荷谱下的疲劳裂纹扩展情况,并分析随机载荷谱下载荷次序效应及初始裂纹尺寸对疲劳裂纹扩展行为的影响.结果表明,载荷次序效应对潜艇结构疲劳寿命的影响很明显,且合理的确定初始裂纹尺寸对潜艇结构的疲劳寿命预报是非常重要的.     

船体在疲劳和腐蚀损伤下的可靠性

在疲劳和腐蚀作用下，船体梁舯剖面模数折减，导致极限承载能力下降，在此基础上进行可靠性分析。文中腐蚀率是一个有常数平均值的随机变量，疲劳裂纹根据Paris公式计算，当静水弯矩和波浪弯矩的组合值超过船体梁极限承载能力时，发生船体梁失效。以一艘散货船为例，计算其可靠性随时间的变化。计算结果可为船东和船级社评估船舶营运期间疲劳和腐蚀对船舶可靠性的影响提供参考。     

船体结构表面裂缝在应力腐蚀耦合作用下的扩展机理数值研究

用数值方法研究了船体表面微裂缝在海水腐蚀以及外荷载耦合作用下扩展的机理.实验表明,在给定材料和腐蚀环境的条件下,外荷载越小,微裂缝扩展并最终导致材料断裂破坏过程越长;但当荷载小于某个值(门槛值或称疲劳极限)时,这种延迟的腐蚀断裂破坏现象可以避免.为研究方便,文中假设了在腐蚀环境中工作的材料为各向同性材料.根据数值计算结果,共发现了三种可能的裂缝扩展形式,并证实了导致腐蚀疲劳断裂临界条件的存在性.最后通过计算,针对不同材料以及不同环境条件,勾勒出导致腐蚀疲劳断裂相应的临界条件曲线.     

基于腐蚀疲劳裂纹扩展的自升式海洋平台桩腿时变可靠性研究

本文研究了腐蚀与疲劳载荷耦合作用下自升式平台桩腿服的可靠性问题。采用ANSYS对自升式海洋平台桩腿结构进行建模,根据平台服役海域的波浪散布图对桩腿结构的工况进行划分,确定浪溅区桩腿结构的疲劳关键节点及其等效应力;以桩腿材料E690高强钢为对象,进行腐蚀疲劳裂纹扩展实验,获得了不同环境下的疲劳裂纹扩展参数;提出了基于断裂力学的浪溅区桩腿关键节点的时变可靠性模型,与采用现有腐蚀模型的桩腿时变可靠性指标进行了对比,结果表明了本文所提方法能有效地反映平台桩腿服役期间关键节点的时变可靠性变化趋势,为平台在服役期间的安全运行与维护保养提供了理论指导。