Minimizing the Path Radius of Curvature for Collision Avoidance

Purpose of this article was to especially emphasize the contribution of tires nonuniformity radial and lateral force variation to vehicles vibrations, within developed nonlinear dynamic model of a vehicle. The tire nonuniformity force variations are introduced in simulations processes by radial and lateral dynamic forces in the area of wheels-road contact. The limits of admissible Peak - to - Peak radial and lateral force variation and Peak - to - Peak first harmonic radial and lateral force variation nonuniformity were defined by using a vehicle vibratory model. The tire nonuniformity parameters were defined from the aspect of vertical seat cushion and the steering wheel rim vibrations using the developed optimization program and the Pentium 90 MHz computer.     

Tire wear estimation based on nonlinear lateral dynamic of multi-axle steering vehicle

This paper presents a novel nonlinear dynamic model of a multi-axle steering vehicle to estimate the lateral wear amount of tires. Firstly, a 3DOF nonlinear vehicle dynamic model is developed, including dynamic models of the hydropneumatic suspension, tire, steering system and toe angle. The tire lateral wear model is then built and integrated into the developed vehicle model. Based on the comparison of experimental and simulation results, the nonlinear model is proved to be better than a linear model for the tire wear calculation. In addition, the effects of different initial toe angles on tire wear are analyzed. As simulation results shown, the impact of the dynamic toe angle on the tire wear is significant. The tire wear amount will be much larger than that caused by normal wear if the initial toe angle increases to 1° - 1.5°. The results also suggest that the proposed nonlinear model is of great importance in the design and optimazation of vehicle parameters in order to reduce the tire wear.     

轮胎动力学特性仿真分析研究

分析了各种常用轮胎模型的特点与应用范围,根据汽车操纵动力学研究的需求,在Matlab环境下运用魔术公式建立了轮胎动力学模型,并对汽车轮胎力与纵向滑移率,纵向力、侧向力及回正力矩与纵向滑移率、侧偏角、外倾角、垂直载荷的关系等轮胎特性进行了仿真分析,实验结果表明,魔术公式轮胎动力学模型可以较好地模拟轮胎的动力学特性,适用于车辆动力学研究领域。     

用于动力学模拟的STI轮胎模型分析

介绍了用于汽车驾驶模拟器动力学模拟的STI（Systems Technologies Inc）轮胎半经验模型,建立了该轮胎模型的复合滑移率、横向刚度和纵向刚度以及横向力和纵向力的计算方程,并利用Vc＋＋6．0编程计算得到的理论值与实验值对比,对该模型进行了分析和验证。分析结果表明,该轮胎模型用于车辆动力学模拟时有较好的精度。     

Tire Lateral Force Estimation Using Kalman Filter

As for the tire analysis, lateral tire force is a fundamental factor that describes the stability of vehicle handling. Attempts to analyze the vehicle stability have been made based on various objective test methods and some specific factors such as yaw, lateral acceleration and roll angle. However, the problem to identify which axle is lack of the tire grip at a certain situation still remains. Since indoor tire force measurement system cannot represent a real road and vehicle conditions, tire force measurement through a real vehicle test is inevitable. Due to the high price of the tire force measurement device, tire force estimator can be an alternative toward cost reduction and device failure. In this paper, nonlinear planar full car model combined with tire model is proposed. Then, using discrete-time extended Kalman-Bucy filter (EKBF), individual tire lateral force are estimated with modified relaxation length model.     

用于公路车-桥系统振动分析的精细化轮胎模型

为了解决当前公路车桥耦合振动模型中轮胎模型过于简化、车轮-路面接触力与桥梁响应计算结果不够精确的问题,提出了一种精细化轮胎模型.首先基于车辆橡胶轮胎的几何、力学特征,建立了径向弹簧力学模型并进行了理论推导;然后考虑轮胎与路面接触面的刚度分布特征和高速状况下轮胎的惯性力,提出了轮胎接触面分布刚度的计算方法,保证了轮胎接触...     

Design of a signal transducer for direct conversion of wheel linear accelerations into tire lateral forces

This paper describes a design of a real-time conversion system of wheel linear accelerations into tire lateral forces. Though the tire lateral forces are important elements for analyzing vehicle dynamic control performances, they cannot be easily measured in real-time owing to the non-linearities of tire dynamics, friction, and slippage on road. In this paper, we propose a practical direct method using wheel linear accelerations in order to estimate tire lateral forces transmitted into the vehicle in real-time. A simplified vehicle model based on force-acceleration analysis is proposed to assure the real-time performance. The acceleration values are obtained using three-axis accelerometers attached on each wheel location. For conditioning and rectifying the acceleration signals, a signal transducer is designed using a digital filter. And in order to investigate the feasibility and real-time performance, a prototype of signal transducer is fabricated using a digital signal processor. The experimental results and performance are validated with the road test results using six-component wheel force transducers.     

轮胎附着极限下差动制动对汽车横摆力矩的影响

本文以纵滑－侧偏联合工况的稳态轮胎模型为基础，分析了汽车极限转向条件下制动作用于不同车轮时对汽车横摆力矩的影响，并通过整车动力学仿真进行了验证，研究结果为利用差动制动控制提高汽车的高速操纵稳定性提供了动力学依据。     

Selfexcited Vibrations of the Tire

In this paper a mechanical work of external forces and torques, acting on the tire has been considered. A theory has been developed for the prediction of necessary conditions for selfexciting vibrations. The theory establishes, that the mechanical work of external forces and torques must be positive, or, what is equivalent, that the tire has to transmit energy from external environment to vehicle. The work of forces and torques has been considered as a convolution of functions, which next has been submitted to Laplace transformation. The condition of selfexcitation of vibrations, obtained from above in the frequency domain, establishes, that the imaginary part of all eigenvalues of frequency response matrix must be negative. As an example, the ranges of selfexcited vibrations of the tire have been calculated. The tire has been treated as a stretched circular string. Four different models have been considered. Three of them have been massles (kinematic), namely Pacejka's model, Von Schlippe's model and single-point model. As fourth model the dynamic Pacejka's model has been considered. The influences of longitudinal deflections on the shimmy tendency have been studied for all models

Frequency response characteristics have been numerically computed and compared for all models. A critical speed and a critical reduced frequency of first and second kind have been defined. Admissible, negative, imaginary parts of the eigenvalues of frequency response matrix have been established. These admissible values of imaginary parts of eigenvalues assure, that the energy absorbing does not excite shimmy vibrations.     

基于整车模型的车-路耦合作用仿真分析

为研究车‐路系统耦合作用下汽车行驶平顺性,运用车辆动力学仿真软件CarSim建立整车模型,并采用傅里叶逆变换法对 GB7031中规定的A~D级路面进行数值仿真与验证,分析了车辆以不同速度行驶在不同等级路面上的加速度和车轮法向动载系数。结果表明:①随着路面等级的降低和车辆行驶速度的提高,车身加速度显著增大,由50 km/h、A级路面上的0.2599 m/s2变化为120 km/h、D级路面上的1.6889m/s2,增加了5.5倍,车辆行驶平顺性下降;②车‐路耦合产生的动载作用受路面工况和车速的影响也较大,由50 km/h、A级路面上的0.0833变化为120 km/h、D级路面上的0.7754,增大8.3倍。路面等级越低,车速越高,动载系数越大,对路面的破坏作用越严重。      

Effects of Model Complexity on the Performance of Automated Vehicle Steering Controllers: Model Development,Validation and Comparison

SUMMARY

Recent research on autonomous highway vehicles has begun to focus on lateral control strategies. The initial work has focused on vehicle control during low-g maneuvers at constant vehicle speed, typical of lane merging and normal highway driving. In this paper, and its companion paper, to follow, the lateral control of vehicles during high-g emergency maneuvers is addressed. Models of the vehicle dynamics are developed, showing the accuracy of the different models under low and high-g conditions. Specifically, body roll, tire and drive-train dynamics, tire force saturation, and tire side force lag are shown to be important effects to include in models for emergency maneuvers. Current controllers, designed for low-g maneuvers only, neglect these effects. The follow on paper demonstrates the performance of lateral controllers during high-g lateral emergency maneuvers using these vehicle models.     

Effects of Model Complexity on the Performance of Automated Vehicle Steering Controllers: Model Development, Validation and Comparison

Recent research on autonomous highway vehicles has begun to focus on lateral control strategies. The initial work has focused on vehicle control during low-g maneuvers at constant vehicle speed, typical of lane merging and normal highway driving. In this paper, and its companion paper, to follow, the lateral control of vehicles during high-g emergency maneuvers is addressed. Models of the vehicle dynamics are developed, showing the accuracy of the different models under low and high-g conditions. Specifically, body roll, tire and drive-train dynamics, tire force saturation, and tire side force lag are shown to be important effects to include in models for emergency maneuvers. Current controllers, designed for low-g maneuvers only, neglect these effects. The follow on paper demonstrates the performance of lateral controllers during high-g lateral emergency maneuvers using these vehicle models.     

Drive control system design for stability and maneuverability of a 6WD/6WS vehicle

This paper describes a drive controller designed to improve the lateral vehicle stability and maneuverability of a 6-wheel drive / 6-wheel steering (6WD/6WS) vehicle. The drive controller consists of upper and lower level controllers. The upper level controller is based on sliding control theory and determines both front and middle steering angle, additional net yaw moment, and longitudinal net force according to the reference velocity and steering angle of a manual drive, remotely controlled, autonomous controller. The lower level controller takes the desired longitudinal net force, yaw moment, and tire force information as inputs and determines the additional front steering angle and distributed longitudinal tire force on each wheel. This controller is based on optimal distribution control and takes into consideration the friction circle related to the vertical tire force and friction coefficient acting on the road and tire. Distributed longitudinal/lateral tire forces are determined as proportion to the size of the friction circle according to changes in driving conditions. The response of the 6WD/6WS vehicle implemented with this drive controller has been evaluated via computer simulations conducted using the Matlab/Simulink dynamic model. Computer simulations of an open loop under turning conditions and a closed-loop driver model subjected to double lane change have been conducted to demonstrate the improved performance of the proposed drive controller over that of a conventional DYC.     

轮胎动态侧偏特性对汽车摆振的影响

轮胎的侧偏力学特性是影响汽车前轮摆振的最关键因素之一，文中在箕是汽车研究所提出了轮胎动态侧偏特性试验方法的基础上，建立了侧向力与回正力矩的精确表达式，并从能量反馈和负阻尼效应研究了轮胎动态侧偏特性参数对汽车偏摆振的影响。     

A Versatile Flat Track Tire Testing Machine

Summary A flat track tire testing machine developed by the IMMa group is described. It permits the simulation and study of the dynamic behavior of a great variety of tires under controllable and repetitive highly dynamic realistic working conditions in the laboratory for a diversity of vehicles, from motorcycles to light trucks. The machine incorporates: - a hydraulically operated tire support and loading system with wide operating ranges; - a computer controlled brake system to simulate braking maneuvers with ABS systems; - a complete sensorial system; - a data acquisition and control system continually monitoring and acting on the experimental variables, i.e., tire and belt speed, longitudinal slip, slip and camber angles, tire pressure, tire normal force, etc. As an application example, results are presented that adjust the parameter of the magic formula for a standard 175/70 R14 passenger vehicle tire. Accurate mathematical tire models are recognized as essential for the prediction of vehicle dynamic performances using simulation tools.     

Design and evaluation of sideslip angle observer for vehicle stability control

This paper presents a method for estimating the vehicle side slip angle, which is considered as a significant signal in determining the vehicle stability region in vehicle stability control systems. The proposed method combines the model-based method and kinematics-based method. Side forces of the front and rear axles are provided as a weighted sum of directly calculated values from a lateral acceleration sensor and a yaw rate sensor and from a tire model according to the nonlinear factor, which is defined to identify the degree of nonlinearity of the vehicle state. Then, the side forces are fed to the extended Kalman filter, which is designed based on the single-track vehicle model associated with a tire model. The cornering stiffness identifier is introduced to compensate for tire force nonlinearities. A fuzzy-logic procedure is implemented to determine the nonlinear factor from the input variables: yaw rate deviation from the reference value and lateral acceleration. The proposed observer is compared with a model-based method and kinematics-based method. An 8 DOF vehicle model and Dugoff tire model are employed to simulate the vehicle state in MATLAB/SIMULINK. The simulation results shows that the proposed method is more accurate than the model-based method and kinematics-based method when the vehicle is subjected to severe maneuvers under different road conditions.     

汽车侧翻和滚翻事故建模研究

分析汽车在侧翻和滚翻过程中的受力状态和轮胎或车身与路面的相互作用方式,建立汽车侧翻和滚翻的运动学和动力学模型,揭示汽车临界侧翻碰撞力与持续作用时间等参数的关系,推导侧翻车辆侧向速度的范围,确定滚筒模型中关键参数的选取方法。事故案例表明模型在实际应用中效果良好、定量准确、直观性强。     

基于自适应模型预测的智能汽车横向轨迹跟踪控制

当路面附着情况和车辆行驶状态不断变化时,基于恒定侧偏刚度的模型预测控制(MPC)不能考虑轮胎非线性特性的影响,难以保证车辆轨迹跟踪的适应性。为此,提出一种考虑轮胎侧向力计算误差的自适应模型预测控制(AMPC),以提高智能汽车在不确定工况下的轨迹跟踪性能。分析了路面附着系数和垂向载荷对轮胎侧向力的影响,基于平方根容积卡尔曼滤波(SCKF)算法,设计了利用侧向加速度和横摆角速度作为测量变量的前后轮胎侧向力估计器。利用轮胎侧向力线性计算值与估计值的差值计算得到侧偏刚度修正因子,设计了前后轮胎侧偏刚度的自适应修正准则,进而提出了一种基于时变修正刚度的AMPC控制方法。基于CarSim与MATLAB/Simulink联合仿真和硬件在环测试平台,对AMPC控制的有效性和实时性进行了验证。研究结果表明：在不同的路面附着情况和车辆行驶状态下,AMPC控制都能够降低横向位置偏差和航向角偏差,有效提高车辆的轨迹跟踪精度,其控制效果明显优于基于恒定侧偏刚度的标准MPC控制。尤其在低附着工况下,标准MPC控制会因为线性轮胎力的计算误差过大而导致车辆在轨迹跟踪时严重失稳,而AMPC控制通过估计轮胎力修正侧偏刚度依然能够保证车辆稳定有效的跟踪参考轨迹。所提出的AMPC控制在保证控制精度的同时具有良好的实时性,对智能汽车控制系统的设计与优化具有重要参考价值。     

Direct tire force generation algorithm based on non-iterative nonlinear inverse tire model

The function of vehicle dynamics control system is adjusting the yaw moment, the longitudinal force and lateral force of a vehicle body through several chassis systems, such as brakes, steering and suspension. Individual systems such as ESC, AFS and 4WD can be used to achieve desired performance by controlling actuator variables. However, integrated chassis control systems that have multiple objectives may not simply achieve the desired performance by controlling the actuators directly. Usually those systems determine the required tire forces in an upper level controller and a lower level controller regulates the tire forces through the actuators. The tire force is controlled in a recursive way based on vehicle state measurement, which may not be sufficient for fast response. For immediate force tracking, we introduce a direct tire force generation method that uses a nonlinear inverse tire model, a pseudo-inverse model of vehicle dynamics and the relationship between longitudinal force and brake pressure.     

New Model of Tire Overturning Moment Characteristics and Analysis of Their Influence on Vehicle Rollover Behavior

A newly developed tire model for the Overturning Moment (OTM) characteristics and the analysis of the influence of OTM on vehicle rollover behavior are presented. The new OTM model was developed based on the so-called Magic Formula tire model. The concept of the new model involves identifying the difference between the simple model and the measurements to the newly defined functions. It was seen that the new model agrees very well with the measured data over a wide range of tire vertical loads, slip angles and camber angles. The influence of tire OTM on the vehicle rollover behavior was also investigated by using a full vehicle simulation in which a rather large steering angle was input. The results obtained from the vehicle simulation with three different tire models (model without OTM, simple model and new model) were compared with the experimental results. It was found that the calculated result obtained with the new OTM model agreed best with the experiment.