Flow-induced Noise and Vibration Analysis of a Piping Elbow with/without a Guide Vane

The effect of a guide vane installed at the elbow on flow-induced noise and vibration is investigated in the range of Reynolds numbers from 1.70×10^5 to 6.81×10^5, and the position of guide vane is determined by publications. The turbulent flow in the piping elbow is simulated with large eddy simulation （LES）. Following this, a hybrid method of combining LES and Lighthill＇s acoustic analogy theory is used to simulate the hydrodynamic noise and sound sources are solved as volume sources in code Actran. In addition, the flow-induced vibration of the piping elbow is investigated based on a fluid-structure interaction （FSI） code. The LES results indicate that the range of vortex zone in the elbow without the guide vane is larger than the case with the guide vane, and the guide vane is effective in reducing flow-induced noise and vibration in the 90° piping elbow at different Reynolds numbers.     

长椭球体绕流问题中层流向湍流流动状态转变的数值预测（英文）

In this work, the laminar-to-turbulent transition phenomenon around the two-and three-dimensional ellipsoid at different Reynolds numbers is numerically investigated. In the present paper, Reynolds Averaged Navier Stokes(RANS) equations with the Spalart-Allmaras, SST k-ω, and SST-Trans models are used for numerical simulations. The possibility of laminar-toturbulent boundary layer transition is summarized in phase diagrams in terms of skin friction coefficient and Reynolds number.The numerical results show that SST-Trans method can detect different aspects of flow such as adverse pressure gradient and laminar-to-turbulent transition onset. Our numerical results indicate that the laminar-to-turbulent transition location on the 6:1 prolate spheroid is in a good agreement with the experimental data at high Reynolds numbers.     

质量比对于柔性圆柱体流激振动的影响（英文）

The effect of the mass ratio on the flow-induced vibration(FIV) of a flexible circular cylinder is experimentally investigated in a towing tank. A Tygon tube with outer and inner diameters of 7.9 mm and 4.8 mm, respectively, was employed for the study. The tube was connected to a carriage and towed from rest to a steady speed up to 1.6 m/s before slowing down to rest again over a distance of 1.6 m in still water. Reynolds number based on the cylinder's outer diameter was 800–13,000, and the reduced velocity(velocity normalized by the cylinder's natural frequency and outer diameter) spanned from 2 to 25. When connected, the cylinder was elongated from 420 mm to 460 mm under an axial pre-tension of 11 N. Based on the cylinder's elongated length, the aspect ratio(ratio of the cylinder's length to outer diameter) was calculated as 58. Three mass ratios(ratio of the cylinder's structural mass to displaced fluid mass, m*) of 0.7, 1.0, and 3.4 were determined by filling the cylinder's interior with air, water, and alloy powder(nickel-chromium-boron matrix alloy), respectively. An optical method was adopted for response measurements. Multi-frequency vibrations were observed in both in-line(IL) and cross-flow(CF) responses; at high Reynolds number, vibration modes up to the 3rd one were identified in the CF response. The mode transition was found to occur at a lower reduced velocity for the highest tested mass ratio. The vibration amplitude and frequency were quantified and expressed with respect to the reduced velocity. A significant reduced vibration amplitude was found in the IL response with increasing mass ratios, and only initial and upper branches existed in the IL and CF response amplitudes. The normalized response frequencies were revealed to linearly increase with respect to the reduced velocity, and slopes for linear relations were found to be identical for the three cases tested.     

基于流固耦合方法的两自由度水翼流激振动特性研究（英文）

The flutter of a hydrofoil can cause structural damage and failure, which is a dangerous situation that must be avoided. In this work, based on computational fluid dynamics and structural finite element methods, a co-simulation framework for the flow-induced vibration of hydrofoil was established to realize fluid-structure interaction. Numerical simulation research was conducted on the flow-induced vibration characteristics of rigid hydrofoil with 2-DOF under uniform flow, and the heave and pitc...     

Numerical study on flow-induced noise for a steam stop-valve using large eddy simulation

The noise induced by the fluctuant saturated steam flow under 250 °C in a stop-valve was numerically studied.The simulation was carried out using computational fluid dynamics（CFD） and ACTRAN.The acoustic field was investigated with Lighthill＇s acoustic analogy based on the properties of the flow field obtained using a large-eddy simulation that employs the LES-WALE dynamic model as the sub-grid-scale model.Firstly,the validation of mesh was well conducted,illustrating that two million elements were sufficient in this situation.Secondly,the treatment of the steam was deliberated,and conclusions indicate that when predicting the flow-induced noise of the stop-valve,the steam can be treated as incompressible gas at a low inlet velocity.Thirdly,the flow-induced noises under different inlet velocities were compared.The findings reveal it has remarkable influence on the flow-induced noises.Lastly,whether or not the heat preservation of the wall has influence on the noise was taken into account.The results show that heat preservation of the wall had little influence.     

海床对海洋管道涡旋脱落和受力系数的影响（英文）

The effect of rigid bed proximity on flow parameters and hydrodynamic loads in offshore pipelines exposed to turbulent flow is investigated numerically. The Galerkin finite volume method is employed to solve the unsteady incompressible 2 D Navier–Stokes equations. The large eddy simulation turbulence model is solved using the artificial compressibility method and dual time-stepping approach. The proposed algorithm is developed for a wide range of turbulent flows with Reynolds numbers of 9500 to 1.5×104. Evaluation of the developed numerical model shows that the proposed technique is capable of properly predicting hydrodynamic forces and simulating the flow pattern. The obtained results show that the lift and drag coefficients are strongly affected by the gap ratio. The mean drag coefficient slightly increases as the gap ratio increases, although the mean lift coefficient rapidly decreases. The vortex shedding suppression happen at the gap ratio of less than 0.2.     

Research on vibration and near-field sound radiation of ring-ribbed cylindrical shell coated deadening and decoupling materials

The research on structural vibration and sound radiation of underwater ring-ribbed cylindrical shell, which is coated with a kind of deadening and decoupling materials, becomes a focus in recent years. This paper analyzes the problem on two aspects: model experiment and numerical calculation. The model experiment is carried out including three cases firstly, in which the structural vibration response and radiating acoustic field are measured respectively, and the results gained in these three cases are analyzed to discuss the effect of reducing structural vibration and radiating noise of the deadening and decoupling materials. The coupling FEM/BEM and the SEA methods are both used in numerical calculation, i.e. the arithmetic of the coupling FEM/BEM method is adopted to calculate the low frequency characteristics and the SEA method is adopted to calculate the medium-high frequencies characteristics of the model. By comparing experimental results with numerical calculation results, it is proved that the algorithm adopted in this paper is reasonable.     

潜艇上方近场水下辐射噪声双峰特性的实验研究(英文)

The double-peak characteristic of underwater radiated noise in the near field on top of the target submarine was analyzed in depth on the basis of submarine test data on the sea. The contribution of three major noise sources to the radiated noise of a submarine were compared and analyzed, and emphasis was put on the original source, production mechanism, and their correlative characteristics. On the basis of analysis on underwater tracking and pass through characteristics of the target submarine, the double-peak phenomenon was reasonably interpreted. Furthermore, the correctness of the theoretical interpretation was verified adequately in real submarine tests. The double-peak phenomenon indicates that the space distributing character on submarine radiated noise are both asymmetrical with time and space, whereas that is provided with directivity. Studying the double-peak phenomenon in depth has important reference value and meaning in engineering practice for understanding the underwater radiated noise field of submarines.     

海水风机与不同类型基座耦合的非稳态流动分析（英文）

Environmental effects have an important influence on Offshore Wind Turbine(OWT) power generation efficiency and the structural stability of such turbines. In this study, we use an in-house Boundary Element(BEM)—pan MARE code—to simulate the unsteady flow behavior of a full OWT with various combinations of aerodynamic and hydrodynamic loads in the time domain. This code is implemented to simulate potential flows for different applications and is based on a three-dimensional first-order panel method. Three different OWT configurations consisting of a generic 5 MW NREL rotor with three different types of foundations(Monopile, Tripod, and Jacket) are investigated. These three configurations are analyzed using the RANSE solver which is carried out using ANSYS CFX for validating the corresponding results. The simulations are performed under the same environmental atmospheric wind shear and rotor angular velocity, and the wave properties are wave height of 4 m and wave period of 7.16 s. In the present work, wave environmental effects were investigated firstly for the two solvers, and good agreement is achieved. Moreover, pressure distribution in each OWT case is presented, including detailed information about local flow fields. The time history of the forces at inflow direction and its moments around the mudline at each OWT part are presented in a dimensionless form with respect to the mean value of the last three loads and the moment amplitudes obtained from the BEM code, where the contribution of rotor force is lower in the tripod case and higher in the jacket case and the calculated hydrodynamic load that effect on jacket foundation type is lower than other two cases.     

Adaptive vibration isolation system for diesel engine

An active two-stage isolation mounting, on which servo-hydraulic system is used as the actuator (secondary vibration source) and a diesel engine is used as primary vibration source, has been built. The upper mass of the mounting is composed of a 495 diesel and an electrical eddy current dynamometer. The lower mass is divided into four small masses to which servo-hydraulic actuator and rubber isolators are attached. According to the periodical characteristics of diesel vibration signals, a multi-point adaptive strategy based on adaptive comb filtered algorithm is applied to active multi-direction coupled vibrations control for the engine. The experimental results demonstrate that a good suppression in the effective range of phase compensation in secondary path (within 100Hz) at different operation conditions is achieved, and verify that this strategy is effective. The features of the active system, the development activities carried out on the system and experimental results are discussed in the paper.     

体积噪声场和界面噪声场中声矢量传感器线阵阵增益分析

Acoustic vector sensor consists of pressure and particle velocity sensors,which measure the three-dimensional acoustic particle velocity,as well as the pressure at one location at the same time.By preserving the amplitude and phase information of the pressure and particle velocity,they possess a number of advantages over traditional scalar sensors.Signal-to-noise ratio (SNR) gain (which is often called array gain) is one of such advantages and is always interested by all of us.But it is not unchangeable if the spatial correlation of the noise field varies.Much more important,it is difficult to be given if the noise becomes complex.In this paper,spatial correlation of the vector field of isotropic volume-noise and surface-generated noise has been introduced briefly.Based on the results,the combined SNR output of a vector linear array is investigated and the maximum gain is given in the specified noise.Computer simulation shows that the output of one array in the same noise is not the same in different gestures.And then we find the best gesture through SNR calculation and obtain the biggest gain,which has important meaning to guide how to deploy an array in practice.We also should use the array with respect to the characteristics of the real ambient noise,especially in anisotropic noise field.     

Experimental research on dynamic vibration absorber with negative stiffness for longitudinal vibration control of propulsion shafting system北大核心CSCD

［Objectives］In order to control the first longitudinal vibration mode of propulsion shafting systems, a dynamic vibration absorber with disc spring negative stiffness is proposed and its experimental verification carried out. ［Methods］A test bench is established for the propulsion shafting system containing a dynamic vibration absorber with negative stiffness. According to the first longitudinal vibration mode of the shafting, a dynamic vibration absorber with negative stiffness integrated into the thrust bearing is developed. Vibration transmission tests under different rotational speeds, static thrusts and negative stiffness are then carried out, and acceleration response data on the thrust bearing foundation and shafting is obtained. ［Results ］ The results show that the developed dynamic vibration absorber with negative stiffness can achieve vibration suppression of 7.8 dB for the thrust bearing foundation in the first longitudinal mode of the propulsion shafting with a mass ratio of 1.6%, and the vibration control effect of the negative stiffness dynamic vibration absorber is maintained at 3.3 dB when the natural frequency changes by 5% and the thrust changes by 40%. The vibration response on the thrust bearing foundation and shafting do not deteriorate even at non-optimal negative stiffness. ［Conclusions］This study shows that a dynamic vibration absorber with negative stiffness can effectively suppress vibration transmission at the first longitudinal mode of a shafting under different rotational speeds. © 2023 Authors. All rights reserved.     

Two-dimensional FEM model of Vortex-Induced Vibration of A Circular Cylinder

The finite element method was employed to solve the N-S equation.Incorporated with the vibration equa- tion,the vortex-induced vibration of the circular cylinder is studied by an Arbitrary-Lagrangian-Eulerian(ALE)al- gorithm.The Reynolds number based on the cylinder diameter and the undisturbed flow velocity ranges from 90 to 150. The motion of the cylinder was modeled by a spring-damper-mass system.The numerical model has been validated by comparison with the experimental data in literature.The"lock-in"and"beating"phenomena were successfully repro- duced in the numerical test.     

Characteristics and calculation method of sound radiation of cylindrical shell with porous sound-absorbing material under acoustic excitation北大核心CSCD

［Objective］This paper aims to study the characteristics and calculation method of the vibration and sound radiation of single ring-stiffened cylindrical shells with porous fiber composite materials installed in the inner wall under acoustic excitation. ［Method ］ Based on the equivalent fluid theory model of Johnson–Champoux–Allard (JCA) and the transfer matrix of the multilayer medium, a theoretical formula of the sound absorption coefficient of multilayer sound absorption structures is derived. The three methods for calculating the vibration and sound radiation of a single ring-stiffened cylindrical shell with porous fiber materials under acoustic excitation, namely acoustic solid modeling of porous media, finite element model combined with theoretical formula and imposition of impedance boundary on sound absorption coefficient, are then verified and compared. Finally, the influences of sound-absorbing material's thickness, backed-air gap, static flow resistance, and material arrangement order on the acoustic absorption performance of the cylindrical shell are investigated. ［Results］The results show that laying porous fiber composite materials on the cylindrical shell internally can reduce the vibration and acoustic radiation of cylindrical shell structure. The sound absorption coefficient curve can quickly and effectively predict the resulting trend of the vibration and sound radiation of the cylindrical shell. ［Conclusion］The acoustic absorption performance of sound absorption structures can be effectively improved through the rational design of their properties and arrangement order of the sound-absorbing materials in order to achieve the purpose of vibration and noise reduction. © 2023 Chinese Journal of Ship Research. All rights reserved.     

表面噪声矢量场空间相关特性射线声学建模(英文)

Spatial correlation of sound pressure and particle velocity of the surface noise in horizontally stratified media was demonstrated,with directional noise sources uniformly distributed on the ocean surface.In the evaluation of particle velocity,plane wave approximation was applied to each incident ray.Due to the equivalence of the sound source correlation property and its directivity,solutions for the spatial correlation of the field were transformed into the integration of the coherent function generated by a single directional source.As a typical horizontally stratified media,surface noise in a perfect waveguide was investigated.Correlation coefficients given by normal mode and geometric models show satisfactory agreement.Also,the normalized covariance between sound pressure and the vertical component of particle velocity is proportional to acoustic absorption coefficient,while that of the surface noise in semi-infinitely homogeneous space is zero.     

Parameter optimization and parametric deviation influence for shock resistance of double-stage vibration isolation system with limiters北大核心CSCD

［Objectives］For marine nuclear power plants, the relative displacement of the pump supported by a vibration isolation system should be strictly restricted. In order to improve the shock resistance of a vibration isolation system with displacement limiters, the parameter optimization and parametric deviation influence are studied. ［Methods］The theoretical model of a double-stage vibration isolation system with typical limiter parameters is established, the analysis of the shock response characteristics of the system is carried out using the direct integration method, the optimal limiter parameters are obtained using a genetic algorithm, and the influence of parameter deviation on the shock resistance of the system is studied. ［Results］Limiter parameters significantly affect the shock response characteristics of the vibration isolation system. The optimal limiter parameters improve the shock resistance of the system, but parameter deviation has a great influence on shock resistance. Based on the influence of parameter deviation, a deviation control strategy is proposed in which the elastic parameter should have a positive deviation and the gap parameter a negative deviation. The simulation results show that the proposed strategy can effectively alleviate the shock resistance degradation caused by deviation.［Conclusions］The results of this study can be used to guide the design, manufacturing and variation control of limiters for vibration isolation systems. © 2022 Journal of Clinical Hepatology. All rights reserved.     

多弹性支撑设备的同步定相振动控制研究（英文）

This paper describes an analytical investigation into synchrophasing, a vibration control strategy on a machinery installation in which two rotational machines are attached to a beam-like raft by discrete resilient isolators. Forces and moments introduced by sources are considered, which effectively represent a practical engineering system. Adjusting the relative phase angle between the machines has been theoretically demonstrated to greatly reduce the cost function, which is defined as the sum of velocity squares of attaching points on the raft at each frequency of interest. The effect of the position of the machine is also investigated. Results show that altering the position of the secondary source may cause a slight change to the mode shape of the composite system and therefore change the optimum phase between the two machines. Although the analysis is based on a one-dimensional Euler–Bernoulli beam and each machine is considered as a rigid-body, a key principle can be derived from the results. However, the factors that can influence the synchrophasing control performance would become coupled and highly complicated. This condition has to be considered in practice.     

多种边界条件下任意铺层层合板的基频解析解（英文）

In recent years, as the composite laminated plates are widely used in engineering practice such as aerospace, marine and building engineering, the vibration problem of the composite laminated plates is becoming more and more important. Frequency, especially the fundamental frequency, has been considered as an important factor in vibration problem. In this paper, a calculation method of the fundamental frequency of arbitrary laminated plates under various boundary conditions is proposed. The vibration differential equation of the laminated plates is established at the beginning of this paper and the frequency formulae of specialty orthotropic laminated plates under various boundary conditions and antisymmetric angle-ply laminated plates with simply-supported edges are investigated. They are proved to be correct. Simple algorithm of the fundamental frequency for multilayer antisymmetric and arbitrary laminated plates under various boundary conditions is studied by a series of typical examples. From the perspective of coupling, when the number of laminated plates layers N 8–10, some coupling influence on the fundamental frequency can be neglected. It is reasonable to use specialty orthotropic laminated plates with the same thickness but less layers to calculate the corresponding fundamental frequency of laminated plates. Several examples are conducted to prove correctness of this conclusion. At the end of this paper, the influence of the selected number of layers of specialty orthotropic laminates on the fundamental frequency is investigated. The accuracy and complexity are determined by the number of layers. It is necessary to use proper number of layers of special orthotropic laminates with the same thickness to simulate the fundamental frequency in different boundary conditions.     

船体周围Stokes波浪流耦合VOF模型的数值模拟（英文）

The surface wave generated by flow around a ship hull moving near free surface of water is simulated numerically in this study. The three-dimensional implicit finite volume method(FVM) is applied to solve Reynolds averaged Navier-Stokes(RANS) equation. The realizable k-ε turbulence model has been implemented to capture turbulent flow around the ship hull in the free surface zone. The volume of fluid(VOF) method coupled with the Stokes wave theory has been used to determine the free surface effect of water. By using is a six degrees of freedom model, the ship hull's movement is numerically solved with the Stokes wave together. Under the action of Stokes waves on the sea, the interface between the air and water waves at the same regular pattern and so does the pressure and the vertical velocity. The ship hull moves in the same way as the wave. The amplitude of the ship hull's heave is less than the wave height because of the viscosity damping. This method could provide an important reference for the study of ships' movement, wave and hydrodynamics.     

Influence of slip boundary on flow separation and drag of flow past bluff body at high Reynolds numbers北大核心CSCD

［Objectives］Flow separation increases the drag and noise of underwater vehicles, and influences the controllability of their control surfaces. Therefore, the influence of slip caused by superhydrophobic surfaces on drag reduction and flow separation is studied. ［Methods］A partial slip boundary condition is developed, and the flow around a circular cylinder and foil with a slip boundary at high Reynolds numbers are numerically simulated. ［Results］The results show that the when the slip length increases, the flow around the cylinder goes through three stages: the turbulent Kármán vortex street, laminar Kármán vortex street and non-separation Stokes flow. The drag coefficient increases first and then decreases, and the vortex shedding frequency increases. For flow around a foil, the separation position moves downstream until the separation region disappears when the slip length increases, and the drag coefficient decreases while the lift coefficient increases. ［Conclusions］The results of this study show that for flow past bluff body at high Reynolds number, the slip boundary can control flow separation and reduce drag effectively, providing technical support for the application of superhydrophobic surfaces for the flow control of underwater vehicle appendages. © 2022 Journal of Clinical Hepatology. All rights reserved.