Cycle-simulation turbulence modelling of IC engines

Numerical simulations of IC engines are of high interest for automotive engineers worldwide. The simulation models should be as fast as possible, low-computational effort and predictive tool. The correct prediction of turbulence level inside the combustion chamber of spark ignition engines is the most important factor influencing to the engine working cycle. This paper presents a development of the k-ε turbulence model applied to the commercial cycle-simulation software with the high emphasis on the intake part. The validation was performed on two engine geometries with the variation of engine speed and load comparing the cycle-simulation results of the turbulent kinetic energy and in-cylinder temperature with 3-D CFD results. In order to apply the cycle-simulation turbulence model for the simulation of entire engine map, the parameterization model of turbulence constants was proposed. The parameterized turbulence model was optimized using NLPQL optimization algorithm where the single set of turbulence model parameters for each engine was found. A good agreement of the turbulent kinetic energy during the expansion was achieved when the turbulence affects the flame front propagation and combustion rate as well.     

Route choice of cyclists in Zurich

This paper presents the first route choice model for bicyclists estimated from a large sample of GPS observations and overcomes the limitations inherent in the generally employed stated preference approach. It employs an improved mode detection algorithm for GPS post-processing to determine trips made by bicycle, which are map matched to an enriched street network. The alternatives are generated as a random sample from an exhaustive, but constrained search. Accounting for the similarity between the alternatives with the path-size factor the MNL estimates show that the elasticity with regards to trip length is nearly four times larger than that with respect to the share of bike paths. The elasticity with respect to the product of length and maximum gradient of the route is small. No other variable describing the routes had an impact. The heterogeneity of the cyclists is captured through interaction terms formulated on their average behaviour.     

Review of flywheel based internal combustion engine hybrid vehicles

Hybrid vehicles of different configurations and utilizing different energy storage systems have existed in development for many decades and more recently in limited production. They can be grouped as parallel, series or complex hybrids. Another classification is micro, mild and full hybrids which makes the distinction on the basis of functionality. The common energy storage systems in hybrid vehicles are batteries, supercapacitors and high speed flywheels. This paper aims to review a specific type of hybrid vehicle which involves the internal combustion engine (ICE) as the prime mover and the high speed flywheel as an energy storage device. Such hybrids are now attracting considerable interest given their potential for low cost. It is hence timely to produce a review of research and development in this subject. The flywheel is coupled to the drive line with a continuous variable transmission (CVT). The CVT can be of various types such as electrical, hydraulic or mechanical but usually in this case it is a non-electrical one. Different configurations are possible and the paper provides a timeline of the development of such powertrains with various examples. These types of hybrid vehicles have existed as prototypes for many decades and the authors believe that their development has reached levels where they can be considered serious contenders for production vehicles.     

Airline emission charges: Effects on airfares,service quality,and aircraft design

This paper explores the effect of airline emissions charges on airfares, airline service quality, aircraft design features, and network structure, using a detailed and realistic theoretical model of competing duopoly airlines. These impacts are derived by analyzing the effects of an increase in the effective price of fuel, which is the path by which emissions charges will alter airline choices. The results show that emission charges will raise fares, reduce flight frequency, increase load factors, and raise aircraft fuel efficiency, while having no effect on aircraft size. Given that these adjustments occur in response to the treatment of an emissions externality that is currently unaddressed, they represent efficient changes that move society closer to a social optimum.     

Location of bus garages

The location of bus garages is a complex issue that has received recent attention in the literature. Given a bus system, the number of bus garages and their locations depend on garage cost, deadheading cost and environmental impacts. An approximate analytical model is used to determine the number of bus garages that minimizes the above costs. The concept of a slowly varying density of bus-route origins (hence deadheads) per unit area is used to model deadheading costs. The increased deadheading caused by breakdowns and accidents is also considered. The garage cost is modeled as a function of the number of buses stored. A closed-form solution is obtained for the optimal density of garages, when the garage cost function is linear. The actual locations of garages and the allocations of buses to the garages are found using a discrete space location-allocation model formulated so as to consider the environmental impact associated with buses deadheading through populated neighborhoods.     

Influence of vehicular traffic on urban air quality – A case study of Hyderabad,India

In the present study, impact of vehicular traffic emissions on black carbon aerosol mass concentration, trace gases and ground reaching solar radiation were analyzed during nationwide truck strike of 5–12 January, 2009 over urban environment of Hyderabad, India. A significant reduction of about 57%, 60%, 40% and 50% was observed in black carbon, particulate matter, carbon monoxide and ozone respectively during nationwide truck strike period. Results of the study are important for source apportionment of pollutants as the strike created natural laboratory for studying the impact of diesel operated trucks on urban air quality.     

Safety culture on board six Swedish passenger ships

This paper presents the results of a Swedish study on maritime safety culture. The study aims to increase knowledge about the characteristics of safety culture in the maritime setting and about the relationship between safety culture and organizational climate. Such knowledge can be vital in the process of developing and improving safety culture. The paper reports the results of safety culture assessments on board six Swedish passenger ships in international traffic, using observations, questionnaires, and interviews focussing on 508 employees who completed the questionnaires. The results of the assessments revealed a generally good existing safety culture. Differences in individuals' safety culture perceptions were found between ships, vessel type (high-speed craft versus Ropax), and hierarchical working position. Important relationships between organizational climate and safety culture were also found. A comparison with other transport sectors where the same safety culture assessment had been applied yielded that passenger shipping has an average safety culture score level that falls between air traffic control and airport ground handling. The method of assessment, which can be used by shipping companies and vessel crews, identified specific areas of concern in the safety culture that could support continuous improvements of safety and safety culture.     

Development of hot stamped center pillar using form die with channel type indirect blank holder

The hot stamping process has been used in the automotive industry to reduce the weight of the body-in-white and to increase passenger safety via improved crashworthiness. However, defects such as fracture and wrinkle occur when hot stamping is performed using a conventional drawing or forming method. In this study, a channel-type indirect blank holder (CIBH) is proposed to develop a high-strength center pillar in form-type hot stamping, so that the aforementioned drawbacks are overcome. This type of blank holder plays an important role in reducing severe wrinkling at the flange; such wrinkling leads to folding after the completion of form-type hot-stamping. First, we investigated the effect of the channel shape on the indirect blank holding force by using a simplified two-dimensional plane-strain stamping process. Second, we selected the slope angle and corner radius of the channel as the main shape parameters by finite element analysis and artificial neural network (ANN). It is known that fracture at the hot formed wall and wrinkle at the flange are significantly affected by the slope angle of the channel, and the appropriate value for eliminating fracture and wrinkle is determined to be 99°. By performing hot stamping using a form die with the selected channel, we can manufacture a high-strength center pillar without wrinkle and fracture.     

Multiaxial stress creep rupture mechanisms of AZ31 magnesium alloy

The maximum principal stresses, von Mises effective stresses and principal facet stresses at the time of creep rupture were compared in uniaxial, biaxial, and triaxial stress states for AZ31 magnesium alloy. The creep rupture of this alloy was experimentally controlled by cavitation, which was the result of a low damage tolerance, λ. Creep deformation could be correlated with the von Mises effective stress parameter. The failure-mechanism control parameter governing the stress state coincided with the experimental results of the rupture of the materials under multiaxial stress states. Finally, the theoretical prediction based on constrained cavity growth and continuous nucleation agreed with the experimental rupture data to within a factor of three.