Interval estimation in the calibration of certain trip distribution models

This paper argues for interval, rather than point, estimation when calibrating some variants of the trip distribution “gravity” models. Analytic expressions are derived for the approximate asymptotic covariances of least squares and maximum likelihood estimates of the parameters in the impedance function under a variety of conditions. A comparative numerical example, and an application using migration flows, are also presented.     

Satellite and resort offices in Japan

Environmental and qualify-of-life issues are taking on an increasing social and political significance the world over. Even in Japan, a country so often criticized for its economic-dominated outlook, talk is turning to these issues. Advances in telecommunications and a growing awareness of the need to change how we live and function in an increasingly threatened environment has brought telework to the forefront of the debate on the nature of work and how our cities function.After setting the broad Japanese social context, this paper will look at the progress of telework in Japan to date with especial emphasis on several current satellite and resort office pilots. It will summarize the findings and proposals of several available reports, and will also attempt to identify the overall outlook for telework in Japan.     

Application of a 3-D variational inverse model to the analysis of ecohydrodynamic data in the Northern Bering and Southern Chukchi Seas

In the scope of the Inner SHelf Transfer And Recycling Program, extensive oceanographic surveys were conducted in the Northern Bering and Southern Chukchi Seas. A vast amount of hydrographic, chemical and biological data were collected in order to increase the information available on the system and to test if biological observations are indeed compatible with the dominant hydrographic regimes. An original model, based on the variational inverse method, was developed with the aim of reconstructing realistic three-dimensional fields of the variables of interest and giving an interpretation of the observations consistent with the physics of the general circulation. The basic formulation of the model is quite general and provides a very helpful tool in the context of interdisciplinary studies. In a first stage, the vertical and horizontal structures of physical variables are reproduced and discussed. Secondly, a sketch is proposed to explain the driving mechanisms of the primary productivity in the Northern Bering Sea. In particular, one shows that the hydrodynamic regimes strongly condition the behaviour of the ecosystem and are mainly responsible for the very fertile environment that characterizes the Southern Chukchi Sea.     

Development of a low-noise cooling fan for an alternator using numerical and doe methods

An alternator, which converts mechanical rotational energy into electrical energy, is an important component of a vehicle. Alternators operate over a broad range of rotational speeds, typically from 3,000 RPM to 18,000 RPM, which demands a cooling fan producing sufficient airflow, ideally with a minimum of noise. In the current study, an optimized alternator-cooling fan was developed through a linked DOE(Design OF Experiment) process and numerical analysis. The SC/Tetra and FlowNoise S/W programs were used to calculate flow rates and noise levels, respectively, for the newly developed fan. Compared with original model, the numerical results predicted a 3 dBA noise reduction; the measured reduction was 4 dBA.     

Model-based design of a variable nozzle turbocharger controller

Variable Nozzle Turbocharger (VNT) was invented to solve the problem of matching an ordinary turbocharger with an engine. VNT can harness exhaust energy more efficiently, enhance intake airflow response and reduce engine emissions, especially during transient operating conditions. The difficulty of VNT control lies in how to regulate the position of the nozzle at different engine working conditions. The control strategy designed in this study is a combination of a closed-loop feedback controller and an open-loop feed-forward controller. The gain-scheduled proportional-integral-derivative (PID) controller was implemented as the feedback controller to overcome the nonlinear characteristic. As it is difficult to tune the parameters of the gain-scheduled PID controller on an engine test bench, system identification was used to identify the plant model properties at different working points for a WP10 diesel engine on the test bench. The PID controller parameters were calculated based on the identified first-order-plus-dead-time (FOPDT) plant model. The joint simulation of the controller and the plant model was performed in Matlab/Simulink. The time-domain and frequency-domain performances of the entire system were evaluated. The designed VNT control system was verified with engine tests. The results indicated that the real boosting pressure traced the target boosting pressure well at different working conditions.     

Deflection test and transmission error measurement to identify hypoid gear whine noise

T-Hypoid gears are commonly used in rear-drive and 4WD (4 Wheel Drive) vehicle axles. Investigating their sensitivity to deflections is one of the most important aspects of their design and optimization procedures. Therefore, a deflection test was performed in this study in the actual gear mounting using completely processed gear. This test covered the full operating range of gear loads from “no load” to “peak load”. Under peak load, the contact pattern extended to the tooth boundaries without showing a concentration of the contact pattern at any point on the tooth surface. The transmission error was tested under an axle assembly triaxial-real-car-load condition.     

Development of a navigation algorithm with dead reckoning for unmanned ground vehicles

A navigation algorithm is indispensable for Unmanned Ground Vehicles (UGVs). During driving, UGVs follow a global path. In this study, we propose a navigation algorithm using Real Time Kinematic (RTK)-Differential Global Positioning System (DGPS) units and encoders to complement global path planning. Sometimes GPS systems lose their signals and receive inaccurate position data due to many factors, such as edifice and barrier obstructions. This paper shows that GPS deviations can be solved using a Dead Reckoning (DR) navigation method with encoders and that position errors can be decreased through the use of RTK-DGPS units. In addition to this method, we will introduce a new waypoint update algorithm and a steering algorithm using RTK-DGPS units.     

Modified lateral control of an autonomous vehicle by look-ahead and look-down sensing

This paper presents a modified lateral control method for an autonomous vehicle with both look-ahead and look-down sensing systems. To cope with sensor noise and modeling uncertainty in the lateral control of the vehicle, a modified LMI-based H lateral controller was proposed, which uses the look-ahead information of the lateral offset error measured at the front of vehicle and the look-down information of the vehicle yaw angle error between the reference lane and the centerline of the vehicle. To verify the safety and the performance of the lateral control, a scaled-down vehicle was developed, and the positioning of the vehicle was estimated with USAT. The proposed controller, which uses both look-ahead and look-down information, was tested for lane changing and reference lane tracking with both simulation and experiment. The simulation and experimental results show that the proposed controller has better tracking and handling performance compared with a controller that uses only the look-ahead information of the target heading angle error.     

License plate extraction method for identification of vehicle violations at a railway level crossing

The primary cause of most railroad accidents is vehicle entry into railway level crossings despite warning messages. To identify drivers who violate railway level crossing regulations, vehicle license plate recognition can be applied at railway level crossings. The purpose of this paper is to present an effective method for extracting the license plate region from vehicle images taken at railway level crossings. The method proposed in this paper uses the variation in the gray-level values across the image of a license plate. For license plate region extraction, the character region is first recognized by identifying the character width and the difference between the background region and the character region. The license plate region is then extracted by finding the inter-character distance in the plate region. In addition, the license plate type is identified by the difference in the gray-level value between the background region and the character region. The proposed method is effective in solving the current challenges in extracting the license plate region from the damaged frames of license plates issued for domestic use, including new types of license plates. According to the experimental results, the proposed method yields a high extraction rate of 99.5% for vehicle license plates.