An intersection turning movement estimation procedure based on path flow estimator

Estimation of intersection turning movements is one of the key inputs required for a variety of transportation analysis, including intersection geometric design, signal timing design, traffic impact assessment, and transportation planning. Conventional approaches that use manual techniques for estimation of turning movements are insensitive to congestion. The drawbacks of the manual techniques can be amended by integrating a network traffic model with a computation procedure capable of estimating turning movements from a set of link traffic counts and intersection turning movement counts. This study proposes using the path flow estimator, originally used to estimate path flows (hence origin–destination flows), to derive not only complete link flows, but also turning movements for the whole road network given some counts at selected roads and intersections. Two case studies using actual traffic counts are used to demonstrate the proposed intersection turning movement estimation procedure. Copyright © 2010 John Wiley & Sons, Ltd.     

An analysis of Metro ridership at the station-to-station level in Seoul

While most aggregate studies of transit ridership are conducted at either the stop or the route level, the present study focused on factors affecting Metro ridership in the Seoul metropolitan area at the station-to-station level. The station-to-station analysis made it possible to distinguish the effect of origin factors on Metro ridership from that of destination factors and to cut down the errors caused by the aggregation of travel impedance-related variables. After adopting two types of direct-demand patronage forecasting models, the multiplicative model and the Poisson regression model, the former was found to be superior to the latter because it clearly identified the negative influences of competing modes on Metro ridership. Such results are rarely found with aggregate level analyses. Moreover, the importance of built environment in explaining Metro demand was confirmed by separating built environment variables for origin and destination stations and by differentiating ridership by the time of day. For morning peak hours, the population-related variables of the origin stations played a key role in accounting for Metro ridership, while employment-related variables prevailed in destination stations. In evening peak hours, both employment- and population-related variables were significant in accounting for the Metro ridership at the destination station. This showed that a significant number of people in the Seoul metropolitan area appear to take various non-home-based trips after work, which is consistent with the results from direct household travel surveys.     

A dichotomous choice survey for quantifying option and non-use values of bus services in Korea

The total economic value for a transportation service consists of use, option, and non-use value. The use benefit is based on a traveler’s willingness to pay for usual consumption of the service. The optional value, on the other hand, is related to the possible use of the service for trips not yet anticipated or currently accommodated by other travel modes. The non-use value, however, is derived from the intrinsic merit of the service, even though a trip-maker never actually or potentially depends on the mode. A closed-ended contingent valuation method is considered for the quantification of the option and non-use values. A survey of single- and double-bounded dichotomous choices is conducted with a case study of South Korean bus operations. A logistic regression model and a survival analysis for the single- and double-bounded approaches, respectively, are applied. The estimation result is examined according to the statistical property required and the behavioral validity expected. In particular, three issues from the output are discussed. First, the results help to show the preferable framework between single- and double-bounded surveys for addressing an individual’s option and non-use values. Second, the differences in the absolute values of option and non-use values are compared. Thirdly, the relationship between trip-makers’ willingness to pay and the level of service of their primary travel modes are investigated. In conclusion, the summary of research and the possibilities for future studies are given.     

Integrated expression method for technical mapping of traffic parameters using RGB color model

In the field of traffic flow, speed, density, time, and distance are fundamental variables analyzed to predict traffic conditions. Reliable sources of information are gauged using tested mathematical approaches that have been developed. However, a fundamental diagram that could serve as a basis for expression techniques has not been devised. Red–green–blue (RGB) color modeling was used to overcome this limitation in traffic flow. The purpose of this study is to provide a way to understand traffic flow conditions based on features of three traffic flow elements simultaneously. The limitation of three‐dimensional expressions in two‐dimensional paper was extended to multi‐dimensional information. Information on speed, density, and flow were combined into a single RGB color and given the name RGB flow‐density space time‐distance space. This cancels out the effect of each individual's vehicular trajectories and contains five major components of a specific road section. The new gizmo aims to provide information on traffic flow conditions in transition and to stimulate further approaches related to the predictions and understanding of traffic flow. Copyright © 2016 John Wiley & Sons, Ltd.     

Numerical study of a light-duty diesel engine with a dual-loop EGR system under frequent engine operating conditions using the doe method

Exhaust gas recirculation (EGR) is an emission control technology that allows for a significant reduction in NOx emissions from light- and heavy-duty diesel engines. The primary effects of EGR are a lower flame temperature and a lower oxygen concentration of the working fluid in the combustion chamber. A high pressure loop (HPL) EGR is characterized by a fast response, especially at lower speeds, but is only applicable if the turbine upstream pressure is sufficiently higher than the boost pressure. On the contrary, for the low pressure loop (LPL) EGR, a positive differential pressure between the turbine outlet and the compressor inlet is generally available. However, a LPL EGR is characterized by a slow response, especially at low and moderate speeds. In this study, of the future types of EGR systems, the dual-loop EGR system (which has the combined features of the high-pressure loop EGR and the low-pressure loop EGR) was developed and was optimized under five selected operating conditions using a commercial engine simulation program (GT-POWER) and the DOE method. Finally, significant improvements in the engine exhaust emissions and performance were obtained by controlling several major variables.     

Low cost design of parallel parking assist system based on an ultrasonic sensor

This paper presents a low cost design and implementation of a parallel parking assist system (PPAS) based on ultrasonic sensors. Generally, a PPAS requires several types of sensors, such as an ultrasonic sensor, camera sensor, radar sensor and laser sensor for parking space detection. However, our proposed PPAS only requires two ultrasonic sensors on the front and lateral sides for parking space detection. Moreover, a steering angle sensor and wheel speed sensor installed in the vehicle are used to obtain vehicle position information for localization in ultrasonic range data. The hardware architecture of the PPAS based on an electronic control unit (ECU) module, sensor modules and a human machine interface (HMI) module was proposed. Moreover, the software architecture of the PPAS is based on system initialization, scheduling, recognition and a control algorithm. In particular, a novel sensor algorithm was proposed to minimize the vehicle corner error of the ultrasonic sensor. A prototype of the PPAS based on the proposed architecture was constructed. The experimental results demonstrate that the implemented prototype is robust and successfully performs parking space detection and automatic steering control. Finally, the low cost design and implementation of the PPAS was possible due to the cheap ultrasonic sensors, simple hardware design and low computational complexity of the proposed algorithm.     

Analysis of an automotive ground system based on its steady-state model

As more electrical equipment is installed and larger currents are required in vehicles, the automotive ground system becomes more important to guarantee the stable operation of the equipment and efficient power consumption. In this paper, an automotive ground system is analyzed in a steady-state condition, and a simulation model for estimating its ground voltage distribution is described. The automotive ground system is divided into an engine compartment ground and a body ground, and it is modeled as an equivalent resistor network, which is suitable for simulation. By using the developed model, ground voltages are simulated and measurements are taken with a real car. A comparison of the simulation and measurement results shows good agreement, and the validity of the model is confirmed. Then, the factors that dominate the ground voltage level are discussed.     

大个子的进步 比亚迪F6C-NCAP碰撞试验点评

一说起比亚迪,人们最容易想到的自然是F3。中国汽车工业协会的统计告诉我们,在2009年1～2月自主品牌轿车销量排名中,比亚迪F3仅次于奇瑞QQ排名第二,强大的市场占有份额让人们对比亚迪F3耳熟能详。然而对于后出道的比亚迪F6,虽然市场销量不及前辈F3那般光彩照人,但在C—NCA碰撞试验场上,它的表现却远远胜过了F3。     

Dependence of fatigue limit of high-tension bolts on mean stress and ultimate tensile strength

High tension bolts in critical joints in internal combustion engines are susceptible to fatigue failure. Computeraided bolted joint design procedures require knowledge of the dependence of bolt fatigue limit on the mean stress and ultimate tensile strength. This dependence is investigated with staircase fatigue limit tests. The test results show that when the bolt fatigue limit is estimated with the nominal stress of the bolt, it decreases with increasing tensile strength and nominal mean stress. However, there is a range of the nominal mean stress where the bolt fatigue limit is almost constant. The test results are interpreted with finite element analysis.     

Structural optimization of a circumferential friction disk brake with consideration of thermoelastic instability

This research suggests a new disk brake design using circumferential friction on the disk of a front-wheel-drive passenger car. The paper compares mechanical performance between the conventional and suggested disk brakes under dynamic braking conditions. Thermoelastic instability is considered in simulation of the test condition. An optimization technique using a metamodel is introduced to minimize the weight of the suggested disk brake. To achieve this goal, the response defined in the optimization formulation is expressed in a mathematically explicit form with respect to the design variables by using a kriging surrogate model, resulting in a simple optimization problem. Then, the simulated annealing algorithm is utilized to find the global optimum. The design results obtained by the kriging method are compared with those obtained from ANSYS analysis.