Analysis of the effect of cold start on fuel economy of gasoline automatic transmission vehicle

FTP75 driving cycle is used in many countries for evaluation of vehicle fuel economy. FTP75 has 3 phases, where the Phase 1 and the Phase 3 have a same velocity profile, but the Phase1, which is known as cold start phase, shows lower fuel efficiency than the Phase 3. In order to analyze the difference of fuel economy between Phase 1 and Phase 3, vehicle tests are performed. The test results show that the differences of fuel economy is ranging from 3.9% to 18.5%. The factors of the difference of fuel economy for gasoline automatic transmission vehicles are analyzed in this research. The key factors affecting the difference of fuel economy are engine friction loss, torque converter loss and accessory loss. The quantitative analysis of these factors is performed.     

Experimental study on mobility of a vehicle with CTIS in soft soil

Recently, the domestic military vehicles currently being developed are installed with a central tire inflation system (CTIS) to control the pressure of tires to increase the contact area between the tires and the ground and improve mobility on soft soils. On the other hand, it is difficult to find technical data based on experiments for designing a CTIS. In this study, to obtain the technical data to set proper pressures according to road conditions a range of mobility tests were performed on soft soil roads, such as sand and clay, according to the CTIS operating modes to obtain the technical data to set proper pressures according to the road conditions. The characteristics of the mobility and its correlation with the tire pressures in each operating mode were analyzed. The results confirmed that a wheeled vehicle with a CTIS showed better performance on soft soil than a vehicle without a CTIS.     

Added resistance acting on hull of a non ballast water ship

In this paper, added resistances acting on a hull of non ballast water ship(NBS) in high waves is discussed. The non ballast water ships were developed at the laboratory of the authors at Osaka Prefecture University, Japan. In the present paper, the performances of three kinds of bow shapes developed for the NBS were theoretically and experimentally investigated to find the best one in high waves. In previous papers, an optimum bow shape for the NBS was developed in calm water and in moderated waves. For a 2 m model for experiments and computations, the wave height is 0.02 m. This means that the wave height is 15% of the draft of the ship in full load conditions. In this paper, added resistances in high waves up to 0.07 m for a 2 m model or 53% of the full load draft are investigated. In such high waves linear wave theories which have been used in the design stage of a ship for a long time may not work well anymore, and experiments are the only effective tool to predict the added resistance in high waves. With the computations for waves, the ship is in a fully captured condition because shorter waves, λ/Lpp0.6, are assumed.     

Assessing the employment agglomeration and social accessibility impacts of high speed rail in Eastern Australia

There is growing interest in establishing additional evidence, under the umbrella of the wider economy impacts of transport infrastructure projects, to support transport projects in general and public transport projects in particular that struggle to obtain benefit–cost ratios sufficient to gain the support of financial agencies. This paper focuses on one element of wider economy impacts, often referred to as effective economic (employment) density or employment agglomeration impacts, and another, less usually identified, social accessibility impact (SAI) which we refer to as effective social density, which in broad terms provide, correspondingly, evidence of the potential gains in work-related output (often referred to as productivity gains) and potential gains in non-work-related outputs. Both are associated with gains in individual and household benefit attributable to improved accessibility to services linked with populations and particular locations. The SAIs may capture some of the induced benefits in those jurisdictions where these are included routinely in benefit–cost analysis, and the methodology here is most appropriate to those settings where an existing calibrated demand curve may not be available. Using the proposed high speed rail (HSR) project between Sydney and Melbourne as the empirical setting, we identify economic agglomeration and social accessibility benefits for work and non-work related activity respectively. We find the former to be relatively small compared to the significant gains associated with non-work related travel activity, suggesting the greatest benefits associated with HSR, especially for those residents outside of the major metropolitan areas, will be non-work related travel activity.     

Research on the law and controlled limit value of transverse deformation for shield tunnel in soft clayEI北大核心

Research purposes: The transverse deformation of shield tunnel may deeply threaten the safety of tunnel structure. Excessive deformation may lead segment joints to open and leak and segments to craze. The deformation may even cause insufficient cross-section limit and the missing of structural-load-carrying capacity of the tunnel. On the other hand, it costs a lot to repair and reinforce the shield tunnel. In order to determine the proper moment to repair segments and ensure the safety of tunnel structure as well as economical efficiency, it is necessary to study the deformation law and limit value of the transverse section of the tunnel. Research conclusions: Based on the analysis of the influencing factors to causing the transverse deformation, the following conclusions was proposed: (1) The root of transverst deformation is increase of vertical and horizontal load ratio. (2)The shield tunnel properties of Nanjing Metro Line 2 was adapted to analyze the relationship between the variation of tunnel horizontal diameter andmaximum rate of joint opening, tress rate of both bolt and concrete using numerical simulation, furthermore the controlled limit value of transverse deformationwas got, the bolt tress achieve maximal strength when the variation of tunnel horizontal diameter reach 123 mm for sequential segment seams, and 127 mm for staggeredsegment seams, which means severely threaten to the safety of shield tunnel. Finally the precontrol and governance methodswere delivered to different influencing factors. (3)The research results can provide references to determine the controlling methods and restoration moment of the transverse deformation.     

The effect of green time on stochastic queues at traffic signals

Many analyses of traffic signal queues use Webster and Cobbe's formula, which combines the net effect of the red/green cycle with a term representing stochastic effects, idealised as an M/D/1 queue process having random arrivals and uniform service. Several authors have noted that this component should depend not only on demand intensity but also on throughput capacity in each green period, although an extra empirical term may partially allow for this. Extending the service interval in M/D/1 (M = Markovian, i.e. random, D = deterministic, i.e. uniform, 1 = one server) enables the effect to be reproduced, but no exact expressions for its moments are found. Approximate formulae for the extended mean exist but are accurate only near saturation. The paper derives novel approximations for the equilibrium mean and also variance and utilisation, using functions linking traffic intensity with green period capacity. With three moments, equilibrium probability distributions can be estimated for which a method based on a doubly nested geometric distribution is described.     

Vibration path analysis and optimal design of the suspension for brake judder reduction

Brake judder is abnormal vibration, which is mainly generated by uneven contact between the brake disc and pad. The abnormal vibration from BTV (Brake Torque Variation) is transferred to the suspension and the steering system during braking. In this paper, judder simulation is carried out using a multi-body dynamic analysis program to analyze the relationship between judder and the transfer mechanism, which consists of the suspension and the steering system. In order to verify the analytical model, test results are compared with the simulation results. A sensitivity analysis is also carried out. In addition, an optimization method is presented for judder reduction, using the design of experiments.     

Improved hot-stamping analysis of tubular boron steel with direct measurement of heat convection coefficient

There are two types of hot-stamping processes, direct and indirect, depending on the sequence of the heating, forming, and quenching steps and the method used for each step. In this study, an indirect hot-stamping process consisting of forming at room temperature, heating, and water quenching was applied to develop a coupled torsion beam axle. The analysis results indicated that the application of the heat convection coefficient is critical in the simulations and must take into account the temperature and specific location in the model to ensure the accuracy of the heating and quenching analysis. The heat convection coefficients used in the analysis were directly measured at various positions of the tube (e.g., outside, inside, and bending region) using thermocouples, and the final values were determined through correlation between the actual tests and numerical analysis. The experimental and simulated final deformed shape and temperature distribution were in good agreement.     

Fatigue life estimation of injection mold core using simulation-based approach

The purpose of this study is to present a simulation-based approach capable of predicting the fatigue life of a mold core with the help of CAE technology based on injection molding simulation, core stress analysis and fatigue life prediction. Injection molding simulation is performed in order to obtain the non-uniform pressure acting on a mold core due to the polymer melt flow during injection molding process. Subsequently, the melt pressure profile is used as loading condition for core stress analysis via one-way coupling technique. The lifetime of a mold core is then predicted by fatigue analysis with stress-life approach. For verification of simulation-based approach to the fatigue life prediction, tests were also performed.