Seabirds utilizing the Northeast Water polynya

A small seabird community depends on the resources of the Northeast Water (NEW) polynya. In spring, at least 1000 King Eiders and 2500 Common Eiders form pre-breeding congregations at Ob Bank before dispersing in mid June to breeding areas. The most abundant species is the Fulmar, which breeds in six colonies with a total of 2550 “apparently occupied sites”, corresponding to approx. 1475 active pairs in 1993. Kittiwakes occupied almost 900 sites at Mallemukfjeld, with an estimated 733 breeding pairs. The entire NEW area probably holds 400–500 pairs of Ivory Gulls, and about 500 individuals were associated with a colony on Henrik Krøyer Holme; this is one of the world's largest known colonies. Sabine's Gulls breed at the same islands and on Kilen (approx. 50 pairs in each place). Small colonies (total less than 1000 birds) of Arctic Terns are distributed along the edge of the polynya, with the largest colony of about 100 pairs on Henrik Krøyer Holme. The Black Guillemot is the only breeding auk species (< 20 pairs) in the area. Small numbers of Red Phalaropes were observed in the polynya in 1992 and 1993, and the species may have bred at Henrik Krøyer Holme in 1993; the polynya area may also serve as a staging area for transpolar migrants. In late summer a few hundreds of Ross's Gull—non-breeding adults and immatures—show up in and around the polynya, and in recent years a few cases of breeding have also been recorded. The relatively small seabird populations are evidence of a generally low carrying capacity of the polynya area.Apart from the benthic foraging eiders and the Black Guillemot, the seabird community of NEW consists of surface feeders—Fulmars and gulls—dependent on small fish and zooplankton. During their stay in the NEW area, the five most abundant surface feeders will annually consume approximately 243,000 kg (wet weight) of food, of which the Fulmars alone take 67%. Food demand in relation to area of open water in the polynya is highest in spring (approx. 0.2 kg/km²), which is     

Material transport from the nearshore to the basinal environment in the southern Baltic Sea: I. Processes and mass estimates

Processes involved in erosion, transport and deposition of cohesive materials are studied in a transect from shallow (16 m) to deep (47 m) water of the SW Baltic Sea. The wave- and current-induced energy input to the seabed in shallow water is high with strong variability and suspended matter concentrations may double within a few hours. Primary settling fluxes (from sedimentation traps) are less than 10 g m⁻² day⁻¹, whereas resuspension fluxes (evaluated from sedimentation flux gradients) are 15–20 times higher and the residence time for suspended matter in the water column is 1–2 days. Settling velocities of aggregates are on average six times higher than for individual particles resulting in an enhanced downward transport of organic matter. Wave-induced resuspension (four to six times per month) takes place with higher shear stresses on the bottom than current-induced resuspension (three to five times per month). The short residence time in the water column and the frequent resuspension events provide a fast operating benthic–pelagic coupling. Due to the high-energy input, the shallow water areas are nondepositional on time scales longer than 1–2 weeks. The sediment is sand partly covered by a thin fluff layer during low-energy periods. The presence of the fluff layer keeps the resuspension threshold very low (<0.023 N m⁻²) throughout the year. Evaluated from 3-D sediment transport modeling, transport from shallow to deep water is episodic. The net main directions are towards the Arkona Basin (5.5×10⁵ t per year) and the Bornholm Basin (3.7×10⁵ t per year). Energy input to the bottom in deep water is low and takes place much less frequently. Wave-induced resuspension occurs on average once per month. Residence time of particles (based on radioactive isotopes) in the water column is half a year and the sediment accumulation rate is 2.2 mm year⁻¹ in the Arkona Basin.     

Longitudinal Tire Dynamics

This article begins with a brief review of the traditional concept of lateral relaxation length. The review illustrates that this concept yields a useful approximation which can be used with semi-empirical tire models which assume lateral forces are a function of steady-state slip angles. The article then presents an analogous derivation for longitudinal slip. Like its lateral counterpart, the derivation yields an approximation for transient longitudinal slip which can be used with tire models which assume longitudinal forces are a function of steady-state longitudinal slip. It is shown that, like the relaxation-length-based lateral slip angle, this formulation for longitudinal slip yields the ability to compute shear forces at the tire/road interface for either high or low speed applications, a necessary feature of simulations which support human in the loop driving simulation. Like traditional kinematically-based longitudinal slip, the transient formulation presented here is coupled with the wheel spin equation, and it shares the characteristic that it is very stiff compared to the equations of vehicle motion. This characteristic is a challenge impeding the real-time calculations required for driving simulation. The paper shows that local linearization of the wheel spin equations coupled with analytical solutions of the transient longitudinal slip formulation provide the basis for both insight into the longitudinal dynamics of the tire and for integrating the model in real-time.     

Analysis of Tire Effect on the Simulation of Vehicle Straight Line Motion

In the dynamic simulation of vehicle straight line motion, a vehicle model usually drifts from its intended straight path even in the case of no external input. This is particularly true when a tire model based on experimental data is used. The purpose of this paper is to provide an enhancement of a basic understanding of a tire/vehicle system behavior in the straight line motion and to identify the effect of the tire on that motion. Through the analysis of a two degrees of freedom vehicle model, tire characteristic which causes a lateral drift in the straight line motion is identified. Then the results are confirmed from vehicle test and the simulations with a more complex full-car model.     

Rail line length in a crosstown corridor with many-to-many demand

An analytical model that determines the optimal location and length of rail line along a crosstown transportation corridor with the objective of minimizing the total transportation cost is presented. A general, many-to-many passenger demand pattern is considered. The objective function, which includes the rail and bus riding costs, rail and bus operating costs, rail fleet costs and rail line costs, is minimized by using the classical optimization method with the aid of a computer program developed for the model. The model is applied to the Northwest-South transportation corridor in Calgary, Alberta, and the sensitivity of the optimal rail line location and length to the unit cost and demand parameters at their reasonable ranges is tested. It is found that although the total passenger demand, unit rail line cost, and unit bus operating cost have greater influence than the unit bus and rail riding costs, and unit rail fleet and operating costs, the optimal line length is generally insensitive to all these parameters. It is also found that the length of the existing LRT line in the corridor is comparable to the optimal line length obtained from the model, but the existing line should be extended further south in order to meet the heavier demand in that direction optimally.     

Measurement of roof deformation caused by vehicle rollover

A vehicle rollover is a critical accident that could have many causes. This paper describes a novel vision-based system for measuring vehicle roof deformation due to a rollover accident. A vision-based measurement system offers an overall view of structural deformation simply at low cost. Our measurement system was constructed using a Kinect camera from Microsoft, a battery, and a remote-controlled recording computer. Color images and distance maps can be obtained using two sensors embedded in the Kinect along with customized software, and the distance from the camera lens to a specific object can be calculated with a simple equation. To test our proposed approach, actual vehicle rollover experiments were conducted and the resulting roof deformations were compared to those indicated by our system. Moreover, cross-sectional image of Apillar was analyzed to calculate bending moment of inertia. From the research results, it was able to show that deformation errors were within 13 mm, and roof deformation was correlated with vehicle type, or vehicle curb weight.     

Handling Analysis of a Motorcycle with Added Cambering of the Front Frame

Through linear analysis, the handling characteristics of the motorcycle with fixed control of added cambering of front frame are investigated under the variation of fixed and free controls of steering axis. The cornering responses and stability characteristics of the motorcycle are presented with the aid of the handling diagram. From numerical results for a typical motorcycle, it is found that the influence of the cambering of front frame on the cornering response of fixed steering control is opposite to that of free steering control. Moreover, the design philosophy of a so-called semi-direct steering mechanism, which cambers the front frame for cornering, is studied.     

Performance of Low-bandwidth, Semi-active Damping Concepts for Suspension Control

Active damping has been shown to offer increased suspension performance in terms of vehicle isolation, suspension packaging, and road-tire contact force. It can even approximate the performance of full state feedback control without requiring the difficult measurement of tire deflection. Many semi-active damping strategies have been introduced to approximate the response of active damping with the modulation of passive damping parameters. These strategies have typically required a relatively high bandwidth for actuator response. This paper investigates the simulation performance and “frequency response” of two concepts in low-bandwidth semi-active suspension control, one that sets a damping force directly and another that sets the damping resistance. The electronically controlled bandwidth of these actuators is approximately an order of magnitude less than other semi-active devices; high frequency control is handled mechanically. A quarter-car model is studied with the controlled damping replacing both passive and active damping of typical control schemes. Both low-bandwidth damping strategies perform remarkably well compared to both active and high-bandwidth, semi-active damping. In certain dynamic performances, the new semi-active strategies outperform active damping and what the author calls “nominal” semi-active damping.     

Examination of nanoparticles from gasoline direct-injection (GDI) engines using transmission electron microscopy (TEM)

Gasoline direct-injection (GDI) engines have been reported to produce significantly more particulate matter (PM) mass and particulate number (PN) emissions than do port-fuel-injection (PFI) spark ignition engines. Because smallsized particles are of great concern in terms of their regulation, transmission electron microscopy (TEM) was used to evaluate the sizes of primary and aggregate particles that were thermophoretically collected from three different GDI engines under various engine operating conditions. A low load and retarded fuel injection generally reduced the particle size. Consequently, when the fuel injection timing was delayed at low loads, primary and aggregate particles became extremely small. In particular, a number of nanoparticles were sub-23-nm particles. Careful high-resolution TEM (HRTEM) analyses provided the first evidence that these nanoparticles are solid carbon particles with clear fringe patterns and young soot (and/or highly condensed semi-volatiles) with amorphous carbon patterns. Therefore, this result suggests that the current cut-off size at 23 nm for PN regulation in Euro 6 must be further reduced to include sub-23-nm carbon nanoparticles.