Damper modeling for dynamic simulation of a large bus with MR damper

In this study, a large bus is tested to measure its dynamic response by the single-lane change test and the rapid stop test. A full car model is established by ADAMS/Car for computer simulation. For multibody modeling of a large bus, user-defined templates are used in the simulation. Simulation results of the single-lane change test and the rapid braking test are compared to the results of the physical experiments, in which several sensors are installed to measure the vehicle’s responses. The results obtained from the simulation show good agreement with the tests’ results. A dynamic model for the MR(magnetic-rheological) damper is also developed by employing the Magic Formula model, which is widely used in the nonlinear modeling of a tire. Bump simulation of a full car with the MR damper is carried out to verify the performance of the MR damper. The comparison of the simulation results obtained with the MR damper model to the results obtained with the traditional passive damper model showed improved response of the vehicle with the MR damper.     

Effect of fuel stratification on initial flame development: Part 3-high swirl condition

This paper discusses the final investigation into the effect of fuel stratification on flame propagation. In previous works, the characteristics under the no port-generated swirl condition and the low-swirl condition were considered. For this purpose, the initial flame development and propagation were visualized under different axially stratified states in a modified optical single-cylinder SI engine. The images were captured by an intensified CCD camera through the quartz window mounted in the piston. Stratification was controlled by the combination of the port swirl ratio and injection timing. These were averaged and processed to characterize the flame propagation. The flame stability was estimated by the weighted average of flame area and luminosity. The stability was also evaluated through the standard deviation of flame area and propagation distance and through the mean absolute deviation of the propagation direction. The results show that the LML is expanded remarkably under the high-swirl cases up to the highest relative AFRs of 1.71 and 1.75 between 140 and 160CA. In addition, similar to the low-swirl condition, the flame-flow interaction determines the direction of flame propagation, and the governing roles of the two factors vary according to the swirl level; the flow is more important at the higher swirl conditions, and the flame is more important at the lower swirl condition. Finally, fast and stable flame propagation can be achieved under the preferably stratified condition, which is induced by the suitable combination of the high swirl and injection timing.     

Experimental design influences on stated choice outputs: An empirical study in air travel choice

Discrete choice experiments are conducted in the transport field to obtain data for investigating travel behaviour and derived measures such as the value of travel time savings. The multinomial logit (MNL) and other more advanced discrete choice models (e.g., the mixed MNL model) have often been estimated on data from stated choice experiments and applied for planning and policy purposes. Determining efficient underlying experimental designs for these studies has become an increasingly important stream of research, in which the objective is to generate stated choice tasks that maximize the collected information, yielding more reliable parameter estimates. These theoretical advances have not been rigorously tested in practice, such that claims on whether the theoretical efficiency gains translate into practice cannot be made. Using an extensive empirical study of air travel choice behaviour, this paper presents for the first time results of different stated choice experimental design approaches, in which respective estimation results are compared. We show that D-efficient designs keep their promise in lowering standard errors in estimating, thereby requiring smaller sample sizes, ceteris paribus, compared to a more traditional orthogonal design. The parameter estimates found using an orthogonal design or an efficient design turn out to be statistically different in several cases, mainly attributed to more or less dominant alternatives existing in the orthogonal design. Furthermore, we found that small designs with a limited number of choice tasks performs just as good (or even better) than a large design. Finally, we show that theoretically predicted sample sizes using the so-called S-estimates provide a good lower bound. This paper will enable practitioners in better understanding the potential benefits of efficient designs, and enables policy makers to make decisions based on more reliable parameter estimates.     

Timetable-based operation in urban transport: Run-time optimisation and improvements in the operating process

Urban public transit provides an efficient means of mobility and helps support social development and environmental preservation. To avoid loss of ridership, transit authorities have focussed on improving the punctuality of routes that operate using timetables. This paper presents a new approach to generating run-time values that is based on analytical development and micro simulations. The work utilizes previous research (described herein) and the experience acquired by Transports Metropolitans de Barcelona (TMB) in operating bus routes based on timetables. Using a sample of historical data, the method used for generating run-time values consists of the following steps: purging and screening atypical trips, based on the consideration of confidence intervals for median trips; segmenting the day into time bands based on the introduction of a new hierarchical classification algorithm; creating initial run-time values based on criteria derived from statistical analysis; adjusting and validating initial run-time values using micro simulations; and evaluating incident-recovery times at the end of trips in order to guarantee the punctual departure of the next trip in the vehicle schedule. To favour service improvement, we also introduced certain indicators that can identify the root causes of non-compliance. As a final step, in order to ensure the applicability and use of the model, we promoted the development of our model within the framework of the HASTUS™ software solution.     

Seaport research: A structured literature review on methodological issues since the 1980s

This study aims to investigate how seaport research has been conducted from the methodological perspective. To this end, this study reviews published port literature for the last three decades (1980-2000s). The investigation primarily categorises the literature according to various methodological issues such as research paradigm, research strategy, base-disciplines, research methods and analysis techniques in order to provide meaningful implications on methodological evolution in seaport research for the period. This study suggests methodological bias in port research to a positivistic paradigm, following a quantitative trajectory moving from conceptual to empirical studies. In addition, the increased use of mathematical modelling and advanced statistical analysis methods is clearly observed. The introduction of advanced analytical tools used in other academic disciplines facilitates discussions in particular research area and amplifies the literature in those areas. This paper also suggests research gaps from the methodological perspective and implications for future port research.     

Railway wheel-flat detection and measurement by ultrasound

This work presents an innovative ultrasound technique designed to detect and quantify flats formed in the rolling surface of railway wheels. Differently from other approaches, ultrasonic pulses (Rayleigh waves) are sent over a measuring rail. The variations in the round-trip time of flight (RTOF) of the ultrasound pulse to the rail-wheel contact point allow detecting and quantifying the wheel-flats. In spite of the wear state of the irregularity, the method provides the loss of material and the length of the flat originally formed by abrasion. A theoretical background supports the technique which offers many advantages for railway maintenance. Simulations and experimental results match the expected ones.     

A network option portfolio management framework for adaptive transportation planning

A real option portfolio management framework is proposed to make use of an adaptive network design problem developed using stochastic dynamic programming methodologies. The framework is extended from Smit’s and Trigeorgis’ option portfolio framework to incorporate network synergies. The adaptive planning framework is defined and tested on a case study with time series origin-destination demand data. Historically, OD time series data is costly to obtain, and there has not been much need for it because most transportation models use a single time-invariant estimate based on deterministic forecasting of demand. Despite the high cost and institutional barriers of obtaining abundant OD time series data, we illustrate how having higher fidelity data along with an adaptive planning framework can result in a number of improved management strategies. An insertion heuristic is adopted to run the lower bound adaptive network design problem for a coarse Iran network with 834 nodes, 1121 links, and 10 years of time series data for 71,795 OD pairs.     

基于纸纤维改性的隧道工程透水砂浆性能研究北大核心CSCD

为提出一种适用于隧道初期支护基面找平并且具有一定透水性能的砂浆,将纸纤维加入砂浆试块中对其性能进行改性。通过分析纸纤维的降解原理,并将不同掺量的纸纤维加入砂浆试块中,对其体积密度、吸水率、抗压强度等基本性能指标及微观结构进行测试和分析。由试验结果可知:在碱性环境中,纸纤维具有可降解的性能特点;纸纤维可以使普通砂浆试块的吸水率提升2~3倍,同时也会造成砂浆试块的体积密度和抗压强度降低;对砂浆试块吸水率和抗压强度进行线性拟合后发现其吸水率和抗压强度呈现负相关关系。研究结果表明,通过纸纤维对砂浆进行透水性能的提升是可行的,但是纸纤维掺量对砂浆其他性能的影响还有待进一步研究。     

Estimation of road profile variability from measured vehicle responses

When assessing the statistical variability of fatigue loads acting throughout the life of a vehicle, the question of the variability of road roughness naturally arises, as both quantities are strongly related. For car manufacturers, gathering information on the environment in which vehicles evolve is a long and costly but necessary process to adapt their products to durability requirements. In the present paper, a data processing algorithm is proposed in order to estimate the road profiles covered by a given vehicle, from the dynamic responses measured on this vehicle. The algorithm based on Kalman filtering theory aims at solving a so-called inverse problem, in a stochastic framework. It is validated using experimental data obtained from simulations and real measurements. The proposed method is subsequently applied to extract valuable statistical information on road roughness from an existing load characterisation campaign carried out by Renault within one of its markets.