泥浆悬浮砂粒能力分层测定试验研究

为实现泥浆悬浮砂粒能力的量化分析,提出一种分层测定方法,选取12%、15%和18%3种质量分数的试验泥浆,通过自行设计的分层取样装置进行试验研究,获取不同泥浆质量分数、沉降时间和砂粒粒径条件下的10个深度分段的砂粒质量分布,分析各参数影响下的砂粒沉降变化规律。结果表明:1)该分层测定方法可较好地获取不同深度分段的砂粒质量,弥补现有测定方法只能获取底层砂粒沉降质量的不足;2)试验所采用的3种质量分数的泥浆对0.1 mm以上粒径的砂粒悬浮能力均较差。根据砂粒沉降曲线分布特征,提出一种用于判别泥浆悬浮砂粒能力的方法,即砂粒沉降曲线越平缓,各层质量差异性越小,底层质量无明显拐点,不同沉降时间曲线越紧密,则泥浆悬浮砂粒能力越强。     

Robust traffic assignment model: Formulation,solution algorithms and empirical application

ABSTRACT

The deterministic traffic assignment problem based on Wardrop's first criterion of traffic network utilization has been widely studied in the literature. However, the assumption of deterministic travel times in these models is restrictive, given the large degree of uncertainty prevalent in urban transportation networks. In this context, this paper proposes a robust traffic assignment model that generalizes Wardrop's principle of traffic network equilibrium to networks with stochastic and correlated link travel times and incorporates the aversion of commuters to unreliable routes.

The user response to travel time uncertainty is modeled using the robust cost (RC) measure (defined as a weighted combination of the mean and standard deviation of path travel time) and the corresponding robust user equilibrium (UE) conditions are defined. The robust traffic assignment problem (RTAP) is subsequently formulated as a Variational Inequality problem. To solve the RTAP, a Gradient Projection algorithm is proposed, which involves solving a series of minimum RC path sub-problems that are theoretically and practically harder than deterministic shortest path problems. In addition, an origin-based heuristic is proposed to enhance computational performance on large networks. Numerical experiments examine the computational performance and convergence characteristics of the exact algorithm and establish the accuracy and efficiency of the origin-based heuristic on various real-world networks. Finally, the proposed RTA model is applied to the Chennai road network using empirical data, and its benefits as a normative benchmark are quantified through comparisons against the standard UE and System Optimum (SO) models.     

Effect of nozzle orifice diameter on diesel spray tip penetration according to various spray models for CFD simulation with widely varying back pressure

CFD simulations of spray tip penetration with the standard KIVA3V, ‘original gas jet’ and ‘Normal gas jet profile with breakup length formula’ (NGJBL) spray models were performed to investigate the effects of nozzle orifice size and ambient gas density combinations on the spray penetration. The accuracy of the CFD simulation results was estimated by comparing them with available experimental data. The ambient gas density was varied in 12 kg/m³ intervals from 12 to 69 kg/m³ for each nozzle orifice diameter. The nozzle orifice diameters used were 119, 140, 183 and 206 mm. A total of 20 cases in the CFD simulations were considered with combinations of the 4 nozzle orifice diameters and 5 ambient gas densities. CFD simulations with the NGJBL spray model were more accurate than those with either the standard KIVA3V or gas jet spray models as the nozzle orifice diameter and ambient gas density was increased. The NGJBL and original gas jet model is more effective in predicting the spray tip penetration near the nozzle tip region.     

Nanoparticle emission characteristics and reduction strategies by boost pressure control and injection strategies in a passenger diesel engine

This research attempted to analyze nanoparticles and other harmful exhaust emissions in accordance with injection strategies and air-fuel ratio (AFR) changes for small diesel engines. The emission characteristics were analyzed in the medium-speed condition, which is the main driving range of a diesel engine. In the case of particulate matter (PM), the number of particles was measured, analyzed, and compared to identify the correlation and emission characteristics of nanoparticles by using a dilution device and condensation particle counter (CPC), which are international standards for particle measurement recommended by the Particulate Measurement Programme (PMP). The engine torque tended to be reduced as pilot injections were added, and the torque was increased by the increased boost pressure, but reduced by the exhaust pressure increase in a part of the low-load range. The number of nanoparticles was not influenced greatly by the change in AFR, but the reduction effect on the PM weight was great depending on the boost pressure increase. In addition, the number of nanoparticles tended to increase as the fuel injection timing became closer to TDC in all conditions, and its difference became larger with an increase in AFR. In addition, in the case of the pilot injection, nanoparticle emission showed similar characteristics depending on the main injection timing, but it was increased by advanced injection timing when performing the main injection only, and the number of the nanoparticles increased as pilot injections were added. Last, the optimal conditions for EMS calibration were analyzed by selecting the conditions of torque reduction and NOx increase within 5 % from all of the engine operating conditions; optimized conditions are presented.     

Vibration reduction of H/Shaft using an electromagnetic damper with mode change

The objective of this study is to develop a damper that can reduce the amplitude of vibration in various frequency ranges. Previous H/Shaft vibration reduction methods work in a passive way. A dynamic damper reduces the amplitude of vibration at its first mode, but vibration still appears at the second mode. A mass damper or hollow shaft can shift the natural frequency to a lower or higher region. The fixed operating frequency prevents vibration from being reduced outside the operating frequency range. The proposed damper uses electromagnets as either masses or actuators to change the damper mode between dynamic damper mode and mass damper mode. The electromagnetic damper (EMD) can change its mode to respond to the vibration excitation at both low and high frequencies. The vibration reduction performance was evaluated by FRF tests in laboratory and vehicle conditions. The results were compared with those of a dynamic damper and indicate that the amplitude of vibration is reduced by 95.6 % when the EMD is implemented on an H/Shaft, whereas only 61.9 % vibration reduction is achieved by the dynamic damper.     

A study on the stability of a motorcycle wheel–swingarm suspension with chain transmission

The present study describes a possible driving mechanism for a self-excited oscillation observed in motorcycle dynamics, often referred to as chatter. This phenomenon, affecting the performance of road racing motorcycles, has been simulated in straight running braking manoeuvres with multibody motorcycle models. It involves rear suspension bounce and driveline oscillation in the frequency range between 17 and 22?Hz. A simplified model of a motorcycle rear suspension with chain transmission is proposed and its stability in equilibrium configurations is studied via eigenvalue analysis. The sensitivity with respect to all its governing parameters is analysed by means of stability maps and the self-excitation mechanism is explained with the aid of energy balance analysis and phase diagrams. It is found that the key role for the instability onset is played by the gradient of the nonlinear characteristic slip function of the tyre.     

A receding horizon sliding control approach for electric powertrains with backlash and flexible half-shafts

Active control of electric powertrains is challenging, due to the fact that backlash and structural flexibility in transmission components can cause severe performance degradation or even instability of the control system. Furthermore, high impact forces in transmissions reduce driving comfort and possibly lead to damage of the mechanical elements in contact. In this paper, a nonlinear electric powertrain is modelled as a piecewise affine (PWA) system. The novel receding horizon sliding control (RHSC) idea is extended to constrained PWA systems and utilised to systematically address the active control problem for electric powertrains. Simulations are conducted in Matlab/Simulink in conjunction with the high fidelity Carsim software. RHSC shows superior jerk suppression and target wheel speed tracking performance as well as reduced computational cost over classical model predictive control (MPC). This indicates the newly proposed RHSC is an effective method to address the active control problem for electric powertrains.     

State estimation in roll dynamics for commercial vehicles

Accurate lateral load transfer estimation plays an important role in improving the performance of the active rollover prevention system equipped in commercial vehicles. This estimation depends on the accurate prediction of roll angles for both the sprung and the unsprung subsystems. This paper proposes a novel computational method for roll-angle estimation in commercial vehicles employing sensors which are already used in a vehicle dynamic control system without additional expensive measurement units. The estimation strategy integrates two blocks. The first block contains a sliding-mode observer which is responsible for calculating the lateral tyre forces, while in the second block, the Kalman filter estimates the roll angles of the sprung mass and those of axles in the truck. The validation is conducted through MATLAB/TruckSim co-simulation. Based on the comparison between the estimated results and the simulation results from TruckSim, it can be concluded that the proposed estimation method has a promising tracking performance with low computational cost and high convergence speed. This approach enables a low-cost solution for the rollover prevention in commercial vehicles.     

Insights into vehicle trajectories at the handling limits: analysing open data from race car drivers

Race car drivers can offer insights into vehicle control during extreme manoeuvres; however, little data from race teams is publicly available for analysis. The Revs Program at Stanford has built a collection of vehicle dynamics data acquired from vintage race cars during live racing events with the intent of making this database publicly available for future analysis. This paper discusses the data acquisition, post-processing, and storage methods used to generate the database. An analysis of available data quantifies the repeatability of professional race car driver performance by examining the statistical dispersion of their driven paths. Certain map features, such as sections with high path curvature, consistently corresponded to local minima in path dispersion, quantifying the qualitative concept that drivers anchor their racing lines at specific locations around the track. A case study explores how two professional drivers employ distinct driving styles to achieve similar lap times, supporting the idea that driving at the limits allows a family of solutions in terms of paths and speed that can be adapted based on specific spatial, temporal, or other constraints and objectives.