Capacity estimation of torque converters with piston holes using the response surface method and an artificial neural network

In new slim torque converters, lock-up clutches are used to provide high fuel efficiency at low speed. However, the slimness of the converters causes difficulty in heat dissipation, which may damage the friction material and shorten its life span. A cooling hole in the lock-up piston reduces the heat but also reduces the torque because oil flows through the hole due to the pressure difference between the two faces of the piston. In the early stages of the development of this type of torque converter, designers must consider the minimum flow rate required to cool the friction material and the minimum torque capacity required to transmit the engine torque. This research explored two methods of estimating these parameters. In the first method, an estimation equation was derived by combining the response surface method with physical properties such as the centrifugal force, a sudden expansion, a sudden contraction, and the steady flow energy equation. The second method involved the use of an artificial neural network. The feasibility of the estimates based on statistics and on the artificial neural network were confirmed in the design stage by comparing experimental and estimated data. An estimation program was created using the C#.Net language and has been used for actual torque converter designs by the Korea Powertrain Company.     

Grande vitesse ferroviaire et développement économique local : une revue de la littérature

Many high-speed rail (HSR) projects exist in Europe and elsewhere in the world and generate many expectations: economic development, location of new firms and new population, development of tourism, effect on real estate. But these expectations are not always fulfilled. For academic researchers, the myth of the existence of a linear causality between transport infrastructures and spatial, social and economic transformations, according to which automatic effects will occur, has been challenged for a long time. But sometimes, new economic dynamism can be observed. The aim of this paper is to present a review of academic and non-academic literature in order to understand why there is a gap between the academic literature and the regional stakeholders’ expectations.     

Design methodology of component design environment for PHEV

In this study, the design methodology for PHEV component design environment is proposed, which consists of power evaluation, component evaluation, component analysis and vehicle performance evaluation environments. First, PHEV simulators were developed based on the dynamic model of the target PHEV powertrain, and a PHEV control algorithm was designed based on the general power-split type PHEV using MATLAB/Simulink. Experimental results were used to validate the constructed PHEV simulators. The power evaluation environment provides the magnitude and direction of the power between components at the vehicle level at any selected time that the user wants to evaluate. The component evaluation environment is designed to evaluate the parameter behaviors of a component using the effort-flow causality relationship. The component analysis environment is designed to investigate component performance according to the variations of component parameters. The vehicle evaluation environment is designed to evaluate equivalent fuel economy at any selected time. It is expected that the design methodology of the PHEV component design environment proposed in this study can be extended to other x-EVs for evaluating and designing vehicle components.     

Active control strategy on a catenary–pantograph validated model

Dynamic simulation methods have become essential in the design process and control of the catenary–pantograph system, overall since high-speed trains and interoperability criteria are getting very trendy. This paper presents an original hardware-in-the-loop (HIL) strategy aimed at integrating a multicriteria active control within the catenary–pantograph dynamic interaction. The relevance of HIL control systems applied in the frame of the pantograph is undoubtedly increasing due to the recent and more demanding requirements for high-speed railway systems. Since the loss of contact between the catenary and the pantograph leads to arcing and electrical wear, and too high contact forces cause mechanical wear of both the catenary wires and the strips of the pantograph, not only prescribed but also economic and performance criteria ratify such a relevance. Different configurations of the proportional-integral-derivative (PID) controller are proposed and applied to two different plant systems. Since this paper is mainly focused on the control strategy, both plant systems are simulation models though the methodology is suitable for a laboratory bench. The strategy of control involves a multicriteria optimisation of the contact force and the consumption of the energy supplied by the control force, a genetic algorithm has been applied for this purpose. Thus, the PID controller is fitted according to these conflicting objectives and tested within a nonlinear lumped model and a nonlinear finite element model, being the last one validated against the European Standard EN 50318. Finally, certain tests have been accomplished in order to analyse the robustness of the control strategy. Particularly, the relevance or the plant simulation, the running speed and the instrumentation time delay are studied in this paper.     

Comparison of driving characteristics between drivers in Korea and in the united states of America based on driver-vehicle interaction field database

Research and development involving intelligent vehicles of today is geared to safe, driver-friendly and sensitive vehicles that provide a driver with a pleasant and convenient driving environment while preventing him or her from possible risks of accident. In developing convenient and safe vehicles, research on drivers’ driving patterns, reactions and state characteristics depending on road conditions in actual field is essential in order to devise more driver-friendly intelligent vehicles. This paper describes how a driver-vehicle interaction (DVI) field database is built in order to obtain a driver’s input in normal road driving condition on highways, country roads, and city roads, and his or her state information, as well as data on the vehicle and traffic conditions. And the newly built database is compared with the RDCW FOT database established by UMTRI of the US for analysis to suggest that the driving tendencies of drivers in Korea and the road driving conditions are not the same as those in the US, reconfirming the need to establish a DVI field database, which will be used for the development of intelligent vehicles suitable for the Korean environment. The DVI data collected from actual driving in field are anticipated to be widely utilized as basic data for research on various intelligent driving safety systems, advanced driver assistance systems (ADAS) and human-vehicle interface (HVI) that are suitable for the driving environment in Korea.     

Optimal fuel-cut driving method for better fuel economy

Eco-drive methods are being applied in modern passenger cars in the form of LCD displays showing real-time fuel consumption rates. The eco-drive is one of the most promising methods to enhance the fuel economy of vehicles. The ecodrive method can be made more effective by using the fuel-cut function. The fuel is not injected when the driver does not depress the gas pedal of a vehicle with engine speeds higher than approximately 1,500 rpm above the mid-vehicle speed range. This function is known as the fuel-cut function, and almost every modern vehicle is equipped with this function. The fuel-cut is most frequently activated on downhill sections of highway. Therefore, the CO₂ exhausted from the vehicle can be zero in this downhill section. In this study, the fuel-cut function is simulated with CRUISE of AVL to find the most effective driving pattern in downhill sections. Simulations with the CRUISE software showed that the lower limit of the vehicle speed for fuelcut should be raised to improve fuel economy on steeper downhill sections. The fuel economy can be optimized when the fuelcut coasting and reacceleration is completed in the downhill part of the road. The simulation result was also compared to previous test results. Fuel consumption was reduced by approximately 4% in both the experimental and simulated results for the West Coast Highway in South Korea.     

Optimization of blending oil with non-esterified biodiesel fuel using design of experiment at partial engine loads

Non-esterified bio-diesel fuel is more economically feasible than esterified one because of simple manufacturing process that only consists of filtering. Applicability of this fuel on diesel engine with electronic control system was tried and accomplished in a previous research. In this study, optimization adopting a fractional factorial design and response surface methodology was carried out at 25 % and 50 % of engine load in order to verify effectiveness of design of experiment for performance optimization of diesel engine. Pcr and IT mainly affected responses as specific fuel oil consumption and nitrogen oxides regardless of engine load according to the fractional factorial design. Estimations were 310.3 g/kWh of specific fuel oil consumption and 237 ppm of nitrogen oxides at 25 % load, and 233.2 g/kWh of specific fuel oil consumption and 730 ppm of nitrogen oxides at 50 % load according to the response surface methodology. As the results of verification tests, specific fuel oil consumption and NOx were respectively 300.4 g/kWh and 277 ppm at 25 % load, and 236.8 g/kWh and 573 ppm at 50 % load. Since there were small differences between estimations and verifications, adopting Box-Behnken method of the response surface methodology for performance optimization of diesel engine should be considered carefully.     

Effects of altitude on combustion characteristic during cold start of heavy-duty diesel engine

Altitude has a significant effect on combustion of heavy-duty diesel engines, especially during cold start. An experimental study on a heavy-duty diesel engine operating at different altitudes was conducted. Tests were based on a direct injection (DI) turbocharged diesel engine with intake and exhaust pressure controlled by the plateau simulation test system to stimulate altitude conditions including 0 m, 1000 m, 2000 m, 3000 m and 4000 m. Results indicated that the compression and expansion resistance moment reduced and the speed increased during the cranking period. The peak pressure of several cycles was increased during the start-up period; however, the expansion pressure dropped more and the indicated mean effective pressure (IMEP) reduced as the altitude rose. While at an altitude of over 2000 m, the peak pressure fluctuated obviously during the start-up period. The higher the altitude was, the more the fluctuation amplitude and cycle number increased and combustion instability enhanced, which resulted the start-up period time increasing at high altitude. When the altitude rose, the cycle-to-cycle variation of the peak pressure and speed fluctuation increased during the idle, the ignition and CA50 were delayed and the combustion duration was shortened. The effect of altitude on combustion characteristics of the diesel engine was more significant during the start-up period than during its idle period.     

Characterization of incidents on an urban arterial road

The early warning of incidents on urban arterial roads in a congested city can reduce delay, accidents and pollutant emission. Freeway incident detection systems implemented in recent years may not be suitable for arterial incidents. Arterial incident detection is more difficult. The traffic flow on an arterial road is not conserved from the upstream end of a road link to the downstream end because urban traffic does turn in and out of side‐streets, car‐parks and local residences. Roadside friction such as kerbside parking and shopping traffic also tends to create apparent incidents which are in fact frequent and normal events. This paper develops a definition for an arterial incident and describes a case study on an arterial road in Melbourne, Australia. The study shows that detectors upstream of an incident are more useful for incident detection than downstream detectors. It also identifies occupancy and speed as the appropriate parameters to characterise and detect arterial incidents.     

Research on a Calculation Method for the Damage Evaluation of the Existing Urban Tunnel Lining Structure北大核心CSCD

The operation safety of the public transport is seriously threaten by the occurrence of defects and damages in existing urban tunnels, which affects the quality of traffic, and will shorten the service life of urban tunnels. Therefore, it is of great significance to evaluate the damages of the tunnel lining structure quickly and accurately. The damage evaluation methods of the existing urban tunnel lining structure are investigated and analyzed in this paper, and a combination method of the macroscopic evaluation of the existing damaged urban tunnel and the damage mechanism of the lining structural material is proposed. Among them, the assessment method specified in the national criterion is selected to evaluate the damages of the lining structure for the macroscopic evaluation, and the classification of tunnel health levels is optimized. Meanwhile, the damage modulus based on the elastic modulus is selected, and the concept of elastic modulus reduction rate is introduced for the mechanism of damage. Furthermore, the assumed function relationship between the health level and the damage degree of existing urban tunnels is proposed and established, which provides a new idea for structural damage assessment of existing urban tunnels. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.