轻轨车辆噪声评价标准初探

根据轻轨车辆噪声的现状及特点,本文认为轻轨车辆的噪声仍以A声级评价为宜,但需规定容许的倍频程带声压值,以抑制低频噪声对人体的影响,同时提出了轻轨车辆噪声的控制标准。最后还指出了A声级评价总体的缺陷,建议应以人体工程学为基础,综合考虑噪声对人体的多方面危害,以制定出更完善的轻轨车辆噪声评价标准。     

Investigation of soot formation in Diesel-GTL fuel blends under quiescent conditions

In this study, a visual investigation of sprays and flames is performed, and soot formation in Diesel-GTL fuel blends is studied in a specially designed quiescent constant-volume chamber under various ambient gas temperatures and O₂ concentrations. Similar to the case of soot formation during diesel fuel combustion, the sooting zone during the mixing-controlled combustion of Diesel-GTL blends is located in the leading portion of the jet boundaries. Auto-ignition delay and soot concentration decrease with an increase of GTL content in the fuel blend. Soot also decreases with lower O₂ concentration, higher injection pressure, and lower ambient gas temperature. The lack of soot formation at lower O₂ concentrations and lower temperatures suggests that Diesel-GTL fuel blends can be successfully utilized in low-temperature diesel combustion technologies that are currently being developed. Furthermore, this mixing controlled combustion method with Diesel-GTL blends can be used to modulate various engine operation parameters, and therefore to simultaneously reduce the formation of soot and NOx within a wide range of diesel engine loads.     

Performance analysis according to the combination of energy storage system for fuel cell hybrid vehicle

The need for the unmanned ground combat vehicle (UGCV), which is used for the surveillance, reconnaissance and targeting during extremely dangerous condition on the battlefield, has steadily increased, and the transition from manned ground combat vehicles to unmanned ground combat vehicles is expected to reduce the loss of lives during battle. The UGCV needs many types of capabilities to achieve satisfactory performance. This paper focuses on the modeling and control of the power system of the UGCV, and proposes the fuel cell hybrid system (FCHS) for the power system of the UGCV. The fuel cell hybrid system has many advantages in stealth drive and the system efficiency. In addition, the FCHS is much quieter than the engine generator and generates much less heat. The benefits of the FCHS are advantageous for use in Army operations, which require ‘silent watch’ capability and the ability to operate without showing up on an enemy’s radar screen. The FCHS has a fuel cell and uses an energy storage system (ESS) as a power source. The ESS (e.g., batteries or ultracapacitors) helps the fuel cell supply power to the electric drive system and also recovers energy during deceleration. The ESS makes it possible to improve the efficiency and dynamic characteristic of the power system. In this paper, the FCHS is composed of different combinations of component models. The component sizes are chosen to satisfy performance requirements. In order to determine the power distribution between the fuel cell and the ESS, a power management strategy based on the required power and the SOC (state of charge) of the ESS is proposed. Batteries and ultracapacitor, components of the ESS, have different characteristics. Accordingly, varying the combination of ESS components can change the performance of the power system. The performance of the FCHS with respect to different combinations of ESS is analyzed using simulated results.     

Evaluation of a vehicle directional control with a fractional order PD<Superscript>μ</Superscript> controller

In this paper, a novel controller, the fractional order PD^μ controller, is designed to improve the performance of the driver-vehicle system. First, fractional calculus and fractional order PI^λD^μ controller are introduced. A control algorithm for vehicle directional control using the fractional order PD^μ controller is then presented. Based on preview-follower theory, the on-line tuning method of the fractional order PD^μ controller is designed. By comparing simulated and experimental results, the validity and robustness of the proposed fractional order PD^μ controller in the closed loop system are verified. Finally, comprehensive evaluations are performed between the systems with the fractional order PD^μ controller and with an integer PD controller. The results demonstrate that the use of the fractional order controller leads to an improvement of the performance of the driver-vehicle system.     

Reaction characteristics of the diesel oxidation catalyst of particulate matters from the diffusion flame of a oiler burner

The objective of this experimental study is to investigate the characteristics of the size distribution and the number concentration of PM (particulate matters) emitted from the diffusion flame of a boiler burner, which has the same type of combustion as a diesel engine. This study is performed to investigate the emission characteristics of nanoparticles generated from diffusion combustion in diesel fuel, and it considered fuel factors and the reaction characteristics of the nanoparticles on the DOC (Diesel oxidation catalyst). The factors examined in this experiment included the sulfur content in the fuel, the blend of the diesel fuel containing biodiesel and bio-ethanol, and the concentration of engine oil (0.1% and 1.0%) blended with diesel fuel. The particle size distribution of the nanoparticles exhausted from the boiler burner was measured by an SMPS (scanning mobility particle sizer). The number concentration of PM that were smaller than 70 nm in diameter greatly increased in the rear of the DOC when fuel containing 250 ppm of sulfur was used. The experiment also suggested that the particle number concentration in both the front and rear of the DOC was lower when ULSD (ultra low sulfur diesel) fuel blended with biodiesel and bio-ethanol, which are oxygenated fuels, was used than when only ULSD fuel was used. The higher the content of engine oil in the fuel, the higher the particle number concentration was in the front and rear of the catalyst. When the first dilution air temperature is increased from 30°C to 180°C, the nanoparticle number concentration dramatically dropped in the rear of the catalyst when fuel containing 250 ppm of sulfur was used, while the particle size distribution remained almost the same when the fuel with engine oil was used.     

Robust <Emphasis Type="Italic">H</Emphasis><Subscript>∞</Subscript> preview control of an active suspension system with norm-bounded uncertainties

A robust H _∞ preview control is investigated for an active suspension system with look-ahead sensors. The uncertain system is described by a state-space model with linear nominal parts and additional nonlinear time-varying norm-bounded uncertainties. Proof of robust stability and a feedback-type robust H _∞ preview controller are derived by augmenting the dynamics of the original system and previewed road input. As, however, the augmented previewed road input gives the system a much larger dimension than the original system, much more computation time is required for solving of Riccati equations. To resolve this problem, a decomposed robust H _∞ preview controller is proposed. Robust stability and performance variations for system uncertainties are shown using a numerical example of a quarter-car model.     

Corrosion characteristics of coated automotive parts subjected to field and proving ground tests

This project evaluated the corrosion damage over a five-year period of organic coated steels in automotive chassis parts during P/G and field tests using electrochemical impedance spectroscopy (EIS) in a 3.5 wt.% NaCl solution. EIS can provide both quantitative kinetic and mechanistic information about the performance of organic coating/metal systems. The difference in coating performance between the P/G and field test specimens was assessed in relation to the impedance parameters. In particular, it was found that the coating resistance and charge transfer resistance could be used to estimate the difference in corrosion damage between the P/G and field test specimens. The coating performance of the P/G and field test specimens was visually evaluated using SEM. The mechanism of corrosion occurring in the P/G test was similar to that taking place in the field test. The field test environment was about ten times as corrosive as the P/G environment in terms of the electrochemical impedance parameters and surface analysis.     

Effect of injection condition and swirl on D.I. diesel combustion in a transparent engine system

The objective of this work was to investigate the effects of injection conditions and swirl on D.I. diesel combustion using a transparent engine system. The test engine is equipped with a common rail injection system to control injection conditions and to obtain split injection characteristics. A combustion analysis and steady flow test were conducted to measure the heat release rate due to cylinder pressure and the swirl ratio. In addition, spray and diffusion flame images were obtained using a high speed camera. The LII & LIS methods were also used to obtain 2-D soot and droplet distributions. High injection pressure was found to shorten ignition delay, as well as to enhance peak pressure. The results also revealed that the heat release rate in the premixed combustion region was markedly reduced through the use of pilot injection, while the soot distribution and the heat release rate in the diffusion combustion region were increased. The swirl effect was found to shorten ignition delay at certain injection timings, and to enhance the heat release rate in all experimental conditions.     

Development of evolutionary cone type LSD for SUV/RV utilizing the axiomatic approach and the ultrasonic nano crystal surface modification technology

Surface topology, cone angle and the forces acting on the cone of the clutch type limited slip differential (LSD) are major design parameters for the bias ratio and the noise condition. Therefore much research has been dedicated to these developments but the results have been used to submit patents. A new cone type limited slip differential for sport utility vehicles and recreational vehicles, which has a very simple structure and easy compliance with the vehicle performance, has been developed by the axiomatic approach and the ultrasonic nano crystal surface modification (UNSM) technology. The design criteria and optimal value of the design parameters are determined by the axiomatic approach utilizing CAE tools. Test methodologies in a test rig and in a vehicle were also developed. Test results showed good performance of bias ratio and noise level but durability is still under testing. This study is an extension of F2006P266, FISITA 2006.     

Computational study on the effects of volume ratio of DOC/DPF and catalyst loading on the PM and NOx emission control for heavy-duty diesel engines

The use of a diesel particulate filter (DPF) in a diesel aftertreatment system has proven to be an effective and efficient method for removing particulate matter (PM) in order to meet more stringent emission regulations without hurting engine performance. One of the favorable PM regeneration technologies is the NO₂-assisted regeneration method due to the capability of continuous regeneration of PM under a much lower temperature than that of thermal regeneration. In the present study, the thermal behavior of the monolith during regeneration and the conversion efficiency of NO₂ from NO with an integrated exhaust system of a diesel oxidation catalyst (DOC) and DPF have been predicted by one-channel numerical simulation. The simulation results of the DOC, DPF, and integrated DOC-DPF models are compared with experimental data to verify the accuracy of the present model for the integrated DOC and DPF modeling. The effects of catalyst loading inside the DOC and the volume ratio between the DOC and DPF on the pressure drop, the conversion efficiency, and the oxidation rate of PM, have been numerically investigated. The results indicate that the case of the volume ratio of ‘DOC/DPF=1.5’ within the same diameter of both monoliths produced close to the maximum conversion efficiency and oxidation rate of PM. Under the engine operating condition of 175 kW at 2200 rpm, 100% load with a displacement of 8.1, approximately 55 g/ft³ of catalyst (Pt) loading inside the DOC with the active Pt surface of 5.3 m²/g_pt was enough to maximize the conversion efficiency and oxidation rate of PM.