Correlation between automotive CO, HC, NO, and PM emission factors from on-road remote sensing: implications for inspection and maintenance programs

Carbon monoxide (CO), hydrocarbon (HC), and nitrogen oxide (NO) emission factors (EFs) are measured with a commercial vehicle emissions remote sensing system (VERSS) during a large-scale vehicle exhaust emissions study in Las Vegas. Particulate matter (PM) EFs are simultaneously measured for individual vehicles with a newly developed PM-VERSS based on ultraviolet backscatter light detection and ranging (Lidar). The effectiveness of CO and HC EFs as proxy for NO and PM EFs for spark-ignition vehicles is evaluated. Poor correlations were found between EFs for pollutants on an individual vehicle basis indicating that high EFs for one or more pollutants cannot be used as a predictor of high EFs for other pollutants. Stronger functional relationships became evident after averaging the EF data in bins based on rank-order of a single pollutant EF. Low overlap between the highest 10% emitters for CO, HC, NO, and PM was found. These results imply that for an effective reduction of the four pollutants, inspection and maintenance (I/M) programs, including clean screening, should measure all four pollutants individually. Fleet average CO and HC concentrations determined by gaseous VERSS were compared with fleet average CO and HC concentrations measured at low-idle and at high-idle during local I/M tests for spark-ignition vehicles. The fleet average CO concentrations measured by I/M tests at either idle were about half of those measured by remote sensing. The fleet average high-idle HC concentration measured by I/M tests was about half of that measured by VERSS while low-idle I/M and VERSS HC average concentrations were in better agreement. For a typical vehicle trip, most of the fuel is burned during non-idle conditions. I/M measurements collected during idling conditions may not be a good indicator of a vehicle’s potential to be a high emitter. VERSS measurements, when the vehicle is under a load, should more effectively identify high emitting vehicles that have a large contribution to the mobile emissions inventory.     

Hub location with flow economies of scale

A characteristic feature of hub and spoke networks is the bundling of flows on the interhub links. This agglomeration of flows leads to reduced travel costs across the interhub links. Current models of hub location do not adequately model the scale economies of flow that accrue due to the agglomeration of flows. This paper shows that current hub location models, by assuming flow-independent costs, not only miscalculate total network cost, but may also erroneously select optimal hub locations and allocations. The model presented in this paper more explicitly models the scale economies that are generated on the interhub links and in doing so provides a more reliable model representation of the reality of hub and spoke networks.     

An Optimal Self-Tuning Controller for an Active Suspension

An optimal self-tuning control algorithm is presented for vehicle suspension design. The controller, incorporating a weighting controller, state observer and parameter estimator, is designed according to linear optimal control (LQG) theory. Based on the updated estimates of vehicle parameters and states, and the adapted weighting parameters, the LQG controller provides the optimal set of gains over different operating conditions. The feasibility and effectiveness of the proposed self-tuning system was investigated and proved by simulation studies.     

车辆行驶工况滚动阻力系数的测定

分析了车辆滚动阻力系数的影响因素，论述了车辆行驶速度对滚阻力系数的影响。依据车辆行驶的功率平衡原理，提出了滚动阻力系数的测试方法及测试时应注意的问题。并对实车测试值与经验公式估算值进行了比较。     

车辆高速行驶安全的思考

分析了轮胎等汽车部件对行车安全的作用，论述了对ABS和车轮定位参数日常检测的必要性．介绍了电涡流中央制动器的制动原理和使用成本。     

鱼雷发动机三组元比例控制器数值模拟

利用计算流体力学软件Pumplinx模拟鱼雷发动机中三组元比例控制器的内部流场,分析计算中不同压差情况下对比例控制器性能的影响,以及叶片与定子间间隙大小对于比例控制器性能的影响,同时对不同叶片数目下性能进行对比。计算结果表明:由于比例控制器为被动旋转马达结构,其转速和流量均随时间呈周期性脉动变化,随着工作压差增大,转速脉动幅度基本保持不变,而流量和扭矩脉动幅值增加;随着间隙增大,泄漏量增大,但流量、扭矩、转速脉动幅值大幅降低,出口流量较为平稳;叶片数目增多后比例控制器转速降低、排量降低。由计算结果推断出目前比例控制器的最优叶片数目为4。本文可为进一步研究比例控制器精度问题提供参考。     

Analysis of the effectiveness of control measures to mitigate road dust emissions in a regional network

The effectiveness of control measures to reduce road dust emissions is analyzed using a year’s data of road dust emissions collected with a mobile sampling platform and a survey of road maintenance practices in the Lake Tahoe Basin of Nevada and California US. Attributes such as sweeping practices, anti-icing, shoulder improvement, pavement condition, trackout, and abrasive material from road segments were analyzed with a feature subset selection algorithm. Street sweeping was found to be an effective means of controlling dust emissions from roads. Road dust from dirty tertiary roads served as a continuous source of suspendable material for adjacent high-speed roads in the winter time. To be most effective, emission control strategies require that not only primary roads, but all roads be swept after snow storms to recover applied abrasive material.     

Optimal Threshold Policies for Robust Data Center Control

With the simultaneous rise of energy costs and demand for cloud computing, efficient control of data centers becomes crucial. In the data center control problem, one needs to plan at every time step how many servers to switch on or off in order to meet stochastic job arrivals while trying to minimize electricity consumption. This problem becomes particularly challenging when servers can be of various types and jobs from different classes can only be served by certain types of server, as it is often the case in real data centers. We model this problem as a robust Markov decision process (i.e., the transition function is not assumed to be known precisely). We give sufficient conditions (which seem to be reasonable and satisfied in practice) guaranteeing that an optimal threshold policy exists. This property can then be exploited in the design of an efficient solving method, which we provide. Finally, we present some experimental results demonstrating the practicability of our approach and compare with a previous related approach based on model predictive control.     

Biogeography-based combinatorial strategy for efficient autonomous underwater vehicle motion planning and task-time management

Autonomous Underwater Vehicles (AUVs) are capable of spending long periods of time for carrying out various underwater missions and marine tasks. In this paper, a novel conflict-free motion planning framework is introduced to enhance underwater vehicle’s mission performance by completing maximum number of highest priority tasks in a limited time through a large scale waypoint cluttered operating field, and ensuring safe deployment during the mission. The proposed combinatorial route-path planner model takes the advantages of the Biogeography-Based Optimization (BBO) algorithm toward satisfying objectives of both higher-lower level motion planners and guarantees maximization of the mission productivity for a single vehicle operation. The performance of the model is investigated under different scenarios including the particular cost constraints in time-varying operating fields. To show the reliability of the proposed model, performance of each motion planner assessed separately and then statistical analysis is undertaken to evaluate the total performance of the entire model. The simulation results indicate the stability of the contributed model and its feasible application for real experiments.