Cycle-simulation turbulence modelling of IC engines

Numerical simulations of IC engines are of high interest for automotive engineers worldwide. The simulation models should be as fast as possible, low-computational effort and predictive tool. The correct prediction of turbulence level inside the combustion chamber of spark ignition engines is the most important factor influencing to the engine working cycle. This paper presents a development of the k-ε turbulence model applied to the commercial cycle-simulation software with the high emphasis on the intake part. The validation was performed on two engine geometries with the variation of engine speed and load comparing the cycle-simulation results of the turbulent kinetic energy and in-cylinder temperature with 3-D CFD results. In order to apply the cycle-simulation turbulence model for the simulation of entire engine map, the parameterization model of turbulence constants was proposed. The parameterized turbulence model was optimized using NLPQL optimization algorithm where the single set of turbulence model parameters for each engine was found. A good agreement of the turbulent kinetic energy during the expansion was achieved when the turbulence affects the flame front propagation and combustion rate as well.     

Protecting Rhode Island's coastal salt ponds: An economic assessment of downzoning

Abstract

In southern Rhode Island, there is growing concern that housing and recreational demands will soon overwhelm the capacity of the coastal salt ponds to absorb wastes, produce seafood, and maintain scenic qualities. As a result, coastal towns have been studying the feasibility of using land controls such as downzoning to protect these coastal amenities. The paper presents an economic analysis of the downzoning program proposed in the town of South Kingstown. Hedonic price and contingent valuation methods are used to value coastal amenities. The estimated net present value of “swimmable” water is shown to be $3.1 million.     

Origin–destination table disaggregation using biproportional least squares estimation

This paper describes a group of techniques for disaggregating origin–destination tables for travel forecasting that makes explicit use of observed traffic on a network. Five models within the group are presented, each of which uses nonlinear least-squares estimation to obtain row and column factors for splitting trip totals from and to larger geographical areas into smaller ones. The techniques are philosophically similar to Fratar factoring, although the solution method is quite different. The techniques are tested on a full-sized network for Northfield, MN and are found to work effectively.     

A regional railroad network optimization model for coal transportation

A regional railroad network is presented to evaluate the system's response to increased coal traffic. An optimal, multimodal, coal-shipping pattern is developed for the study region to minimize total costs and to efficiently use the existing network. A two-stage, general model allocates resources among demands and then assigns flows to the network according to efficiency criteria. The model is sufficiently general to permit modification for specific needs, assumptions and data. Government agencies and industries can apply the model in resource allocation decisions and transportation policy analysis.     

Finite element modeling of static tire enveloping characteristics

To investigate static tire enveloping characteristics, a three dimensional (3-D) finite element model is proposed. The vertical stiffness of the tire is studied on a flat surface with and without cleat. Tire rubber materials and cord layers are represented independently using “rebar” elements available in MSC Marc Mentat. Comparisons of numerical and experimental results are given to show the validity of the proposed model. It is shown that after a certain displacement, the results of the proposed model agree well with experimental results. In addition, the model results show that regardless of the type of the cleat placed under the rim center (hub center), all vertical force curves intersect after a certain displacement, which indicates typical static enveloping characteristics. Moreover, another typical characteristic of the radial tires that is unlike those of bias-ply constructions confirms that the contact patch does not expand laterally after a level vertical load is applied to the tire, which is directly related to fuel consumption and tire tread life.     

Location of bus garages

The location of bus garages is a complex issue that has received recent attention in the literature. Given a bus system, the number of bus garages and their locations depend on garage cost, deadheading cost and environmental impacts. An approximate analytical model is used to determine the number of bus garages that minimizes the above costs. The concept of a slowly varying density of bus-route origins (hence deadheads) per unit area is used to model deadheading costs. The increased deadheading caused by breakdowns and accidents is also considered. The garage cost is modeled as a function of the number of buses stored. A closed-form solution is obtained for the optimal density of garages, when the garage cost function is linear. The actual locations of garages and the allocations of buses to the garages are found using a discrete space location-allocation model formulated so as to consider the environmental impact associated with buses deadheading through populated neighborhoods.     

Development of hot stamped center pillar using form die with channel type indirect blank holder

The hot stamping process has been used in the automotive industry to reduce the weight of the body-in-white and to increase passenger safety via improved crashworthiness. However, defects such as fracture and wrinkle occur when hot stamping is performed using a conventional drawing or forming method. In this study, a channel-type indirect blank holder (CIBH) is proposed to develop a high-strength center pillar in form-type hot stamping, so that the aforementioned drawbacks are overcome. This type of blank holder plays an important role in reducing severe wrinkling at the flange; such wrinkling leads to folding after the completion of form-type hot-stamping. First, we investigated the effect of the channel shape on the indirect blank holding force by using a simplified two-dimensional plane-strain stamping process. Second, we selected the slope angle and corner radius of the channel as the main shape parameters by finite element analysis and artificial neural network (ANN). It is known that fracture at the hot formed wall and wrinkle at the flange are significantly affected by the slope angle of the channel, and the appropriate value for eliminating fracture and wrinkle is determined to be 99°. By performing hot stamping using a form die with the selected channel, we can manufacture a high-strength center pillar without wrinkle and fracture.     

RECENT DEVELOPMENT OF PROCESS SIMULATION AND ITS APPLICATIONS TO MANUFACTURING PROCESSES

l.IntroductionThemostboortantdrivingforceinmanufacturillistoPrOduCeabetterPrOductatalowercost.GenerallyeffecthemethodsinchideshOrtenintheleadtiminthedesigncyCle,andredUcinthetoolingcostandmaChinedOWnmeatProductionst4e.AllOfthemrewtabettertmderstandingofhO…     

Influence of load and inflation pressure on the tyre rolling resistance

Tyre load and inflation pressure are important factors controlling rolling resistance of road vehicles. The article presents results obtained in the Technical University of Gdańsk during laboratory and road measurements of different car tyres rolling on different pavements. The knowledge of rolling resistance characteristics is important for modelling car dynamics as well as fuel consumption. It is also necessary to establish proper test conditions in the future standardized on-road method of measuring rolling resistance. The results indicate that while an increase of load always leads to the increase of rolling resistance force, the influence on Coefficient of Rolling Resistance is more complicated and unpredictable. They also indicate that tyres with high rolling resistance are more sensitive to inflation pressure changes than low rolling resistance tyres.