机外净化技术对 GDI 发动机颗粒排放的影响

通过缸内直喷汽油机颗粒测量试验,研究了怠速工况、最大扭矩工况及常用工况下三效催化器（TWC）和汽油机用颗粒捕集器（GPF）对发动机尾气中颗粒数量浓度及质量浓度的处理效率。结果表明：在低转速小负荷工况,三效催化器与颗粒捕集器对颗粒具有较高的处理效率;随着转速与负荷的增加,两者的处理效率均下降,三效催化器对颗粒处理能力明显降低,而颗粒捕集器整体保持较高的捕集效率;当二者联合工作时,在常用行驶工况下对颗粒的捕集效率达到80％以上。在高转速大负荷工况,由于尾气空速增加,颗粒捕集器捕集效率下降导致整个后处理系统对颗粒的处理效率降低。     

基于 GT-Crank 仿真的柴油机气缸磨损时瞬时转速分析

利用 GT‐Crank 软件对柴油机曲轴瞬时转速进行仿真分析计算,研究了正常状态、单缸磨损、多个相邻缸磨损和多个非邻缸磨损状态下瞬时转速的变化规律,提取了状态特征参数,并分析了气缸磨损对其他缸的影响,为深入研究瞬时转速在柴油机状态检测诊断中的应用提供了理论依据。     

涡轮增压发动机低辛烷值燃料的试验研究

研究基于一台2.3 L四缸的涡轮增压汽油机,国内的推荐燃油为RON95汽油。由于匹配该发动机的车型要出口伊朗,当地的燃油多为RON85汽油;因此,需要在台架上进行低辛烷值燃料的性能开发试验。试验中需要综合调整点火提前角(Spark advanced Angle,SA)、空燃比(Air Fuel Ratio,AFR)以及最大增压压力确保该发动机在任何工况下正常运行,且不发生爆震现象。结果表明:由于使用燃料的辛烷值降低,点火提前角普遍减小。而点火提前角的降低又会引起排气温度的升高,降低空燃比进行催化器保护。接近外特性工况下,通过降低最大增压压力,牺牲发动机的性能来确保其稳定运行。     

Stress sensitivity analysis and optimization of automobile body frame consisting of rectangular tubes

At conceptual design stage, beam element is extensively used to create the frame structure of automobile body, which can not only archive the accurate stiffness but also reduce much computational cost. However, the stress definition of beam element is very complex so that the stress sensitivity and optimization are difficult to analytically derive and numerically program. This paper presents an solution to this problem and an application in the lightweight optimization design of automobile frame. Firstly, maximal Von Mises stress of rectangular tube is calculated by using the superposition of stress, which is together induced by the axial force, bending moments, torsional moment and shear force. Secondly, the sensitivity of Von Mises Stress with respect to size design variables: breadth, height and thickness are derived, respectively. Thirdly, an optimal criterion is constructed by Lagrangian multiplier method to solve the frame optimization with stress constraints. Lastly, numerical example of car frame proves that the proposed method can guarantee the stress of each beam element almost fully reaches at the yielding stress.     

Estimation of maximum road friction coefficient based on Lyapunov method

With the real time and accurate information of motor torque and rotation speed of the four-in-wheel-motordrive electric vehicles, a slip based algorithm for estimating maximum road friction coefficient is designed using Lyapunov stability theory. Modified Burckhardt tire model is used to describe longitudinal slip property of the tire. By introducing a new state variable, a nonlinear estimator is proposed to estimate the longitudinal tire force and the maximum road friction coefficient simultaneously. With the appropriate selection of estimation gain, the convergence of the estimation error of the tire longitudinal force and maximum road friction coefficient is proved through Lyapunov stability analysis. In addition, the error is exponentially stable near the origin. Finally the method is validated with Carsim-Simulink co-simulation and real vehicle tests under multi working conditions in acceleration situation which demonstrate high computational efficiency and accuracy of this method.     

北京市小汽车发展的外部效应分析

从公共经济学角度,对北京市小汽车的发展进行了外部效应分析,指出了随着保用量的增长,对社会产生负外部效应,提出了矫正小汽车发展外部效应的措施建议,希望能够为有关政府部门制定决策提供理论借鉴。     

尾气分析与汽油发动机系统故障诊断

汽油发动机尾气成分直接与发动机的工作情况有关,对发动机在不同工况下尾气中不同成分气体含照的检测和分析,可以判断发动机各系统工作是否正常,也可以据此埘汽油发动机系统进行故障诊断。本文介绍利用尾气分析结果对发动机各系统进行故障诊断的方法。     

超前桩复合土钉墙内部稳定性研究

从超前桩复合土钉墙失稳形式出发,采用理论分析,建立了超前桩复合土钉墙稳定性分析模型,推导出了超前桩复合土钉墙稳定性计算式,并以工程实例进行了验证.     

高寒地区客车前风窗玻璃除霜分析及改进

针对客车在高寒地区前风窗玻璃除霜问题,分析原因,提出改进结构方案,并通过各项测试予以验证。     

钢管混凝土拱桥地震响应分析的参数研究

松岙大桥主桥为260 m的钢管混凝土提篮拱桥,以该桥为研究背景分析桥梁结构的地震时程响应,应用MAT-LAB语言编写了3个程序:人造地震动、采用频域积分法将加速度时程转化为位移时程、由确定的加速度时程求其加速度反应谱,并采用SAP2000为计算平台对上述几种情况下的桥梁地震响应做了对比分析。分析结果显示,大跨度桥梁对于不同的地震波、采用不同的阻尼算法、是否考虑结构的行波效应、是否考虑结构的几何非线性其地震响应差别较大,在分析中应针对具体的桥梁结构确定合理的参数与求解方法。