A simple formulation for predicting the ultimate strength of ships

The aim of this study is to derive a simple analytical formula for predicting the ultimate collapse strength of a single- and double-hull ship under a vertical bending moment, and also to characterize the accuracy and applicability for earlier approximate formulations. It is known that a ship hull will reach the overall collapse state if both collapse of the compression flange and yielding of the tension flange occur. Side shells in the vicinity of the compression and the tension flanges will often fail also, but the material around the final neutral axis will remain in the elastic state. Based on this observation, a credible distribution of longitudinal stresses around the hull section at the overall collapse state is assumed, and an explicit analytical equation for calculating the hull ultimate strength is obtained. A comparison between the derived formula and existing expressions is made for largescale box girder models, a one-third-scale frigate hull model, and full-scale ship hulls.List of symbols A _B total sectional area of outer bottom - A _B total sectional area of inner bottom - A _D total sectional area of deck - A _S half-sectional area of all sides (including longitudinal bulkheads and inner sides) - a _s sectional area of a longitudinal stiffener with effective plating - b breadth of plate between longitudinal stiffeners - D hull depth - D _B height of double bottom - E Young's modulus - g neutral axis position above the base line in the sagging condition or below the deck in the hogging condition - H depth of hull section in linear elastic state - I _s moment of inertia of a longitudinal stiffener with effective plating - l length of a longitudinal stiffener between transverse beams - M _E elastic bending moment - M _p fully plastic bending moment of hull section - M _u ultimate bending moment capacity of hull section - M _uh ,M _us ultimate bending moment in hogging or sagging conditions - r radius of gyration of a longitudinal stiffener with effective plating [=(I _s /a _s )^1/2] - t plate thickness - Z elastic section modulus at the compression flange - Z _B ,Z _D elastic section modulus at bottom or deck - slenderness ratio of plate between stiffeners [= (b/t)(_y/E)^1/2] - slenderness ratio of a longitudinal stiffener with effective plating [=(l/r)(_y/E)^1/2] - _y yield strength of the material - _yB , _yB , _yD yield strength of outer bottom, inner bottom - _yS deck, or side - _u ultimate buckling strength of the compression flange - _uB , _uB , _uD ultimate buckling strength of outer bottom - _uS inner bottom, deck, or side     

Performance indicators for transit management

Transit performance can be evaluated through quantitative indicators. As the provision of efficient and effective transit service are appropriate goals to be encouraged by federal and state governments, these goals are used to develop performance indicators.Three efficiency and four effectiveness indicators are described, together with two overall indicators. These nine indicators are analyzed for comparability utilizing operating and financial data collected from public transit agencies in California.Performance indicators selected for this study should not be viewed as final. Twenty-one performance indicators proposed by previous studies were reviewed. Theoretical considerations and unavailability or unreliability of data caused omission of several useful measures like passenger-miles. Circumstances such as improved data, emphasis upon goals other than efficiency and effectiveness, and local conditions might warrant the inclusion of indicators deleted from this research.This paper is based on work conducted for the Urban Mass Transportation Administration under University Research and Training Grant CA-11-0014, Development of Performance Indicators for Transit. The views expressed herein are those of the authors and not necessarily those of the University of California or the United States Government. We are indebted to John Feren for assistance with the statistical processing and data gathering.     

一种最佳的汽车混合动力总成

介绍了对混合动力总成进行优化的建模及仿真工具《汽车快速性能优化及报告工具包—汽车系统模块(RAPTOR^TM—VSM)软件包》，指出了优化混合动力总成需在混合动力发动机、电动机、电池、超级电容器、动力总成配置和自动／手动变速器(AMT)控制器等方面做的工作。     

Correlation between automotive CO, HC, NO, and PM emission factors from on-road remote sensing: implications for inspection and maintenance programs

Carbon monoxide (CO), hydrocarbon (HC), and nitrogen oxide (NO) emission factors (EFs) are measured with a commercial vehicle emissions remote sensing system (VERSS) during a large-scale vehicle exhaust emissions study in Las Vegas. Particulate matter (PM) EFs are simultaneously measured for individual vehicles with a newly developed PM-VERSS based on ultraviolet backscatter light detection and ranging (Lidar). The effectiveness of CO and HC EFs as proxy for NO and PM EFs for spark-ignition vehicles is evaluated. Poor correlations were found between EFs for pollutants on an individual vehicle basis indicating that high EFs for one or more pollutants cannot be used as a predictor of high EFs for other pollutants. Stronger functional relationships became evident after averaging the EF data in bins based on rank-order of a single pollutant EF. Low overlap between the highest 10% emitters for CO, HC, NO, and PM was found. These results imply that for an effective reduction of the four pollutants, inspection and maintenance (I/M) programs, including clean screening, should measure all four pollutants individually. Fleet average CO and HC concentrations determined by gaseous VERSS were compared with fleet average CO and HC concentrations measured at low-idle and at high-idle during local I/M tests for spark-ignition vehicles. The fleet average CO concentrations measured by I/M tests at either idle were about half of those measured by remote sensing. The fleet average high-idle HC concentration measured by I/M tests was about half of that measured by VERSS while low-idle I/M and VERSS HC average concentrations were in better agreement. For a typical vehicle trip, most of the fuel is burned during non-idle conditions. I/M measurements collected during idling conditions may not be a good indicator of a vehicle’s potential to be a high emitter. VERSS measurements, when the vehicle is under a load, should more effectively identify high emitting vehicles that have a large contribution to the mobile emissions inventory.     

Hub location with flow economies of scale

A characteristic feature of hub and spoke networks is the bundling of flows on the interhub links. This agglomeration of flows leads to reduced travel costs across the interhub links. Current models of hub location do not adequately model the scale economies of flow that accrue due to the agglomeration of flows. This paper shows that current hub location models, by assuming flow-independent costs, not only miscalculate total network cost, but may also erroneously select optimal hub locations and allocations. The model presented in this paper more explicitly models the scale economies that are generated on the interhub links and in doing so provides a more reliable model representation of the reality of hub and spoke networks.     

Fuzzy Logic Active and Semi-Active Control of Off-Road Vehicle Suspensions

For off-road vehicles, minimizing the absorbed power is the main objective of suspension control. The primary cause of increase in the absorbed power in off-road vehicles driven at high speeds on harsh courses is the exhaustion of the suspension travel. Fuzzy-logic approach to active and semi-active off-road vehicle suspension control, with the goal of improving the speed of the vehicle over rough terrains are developed. The ride metric used for quantifying improvements is the absorbed power of the sprung mass. Particular attention is paid to the proper modeling of the suspension using both the full kinematic constraints and the more convenient two degree of freedom linear model of the quarter vehicle suspension. The nonlinearities due to the kinematic constraints on motion are accounted for by modifying the stiffness and damping coefficients of the suspension spring and dashpot in the linear model. The control laws are developed using the less complex model and demonstrated in the fully constrained environment. Nonlinearities of the suspension, including tire stiffness/damping and bumpstops are included at all stages of controller development.     

Lagrangian flow in the California Undercurrent, an observation and model comparison

During the period 1992–1998, 38 isobaric RAFOS floats were deployed to sample the subsurface flow of the California Undercurrent. The deployments, released over the California continental slope west of San Francisco, have sampled robust year-round poleward subsurface flow associated with the Undercurrent most seasons and the combined inshore current and Undercurrent in winter. Two other types of flow have been seen: a region of weak flow with little net displacement just west of the California Undercurrent, and an active westward propagating eddy field. This eddy field appears to be the primary mechanism for moving floats from the Undercurrent into the ocean interior. The observations and statistics from the RAFOS floats are compared with Lagrangian estimates of particles tracked in a global high resolution ocean simulation in order to evaluate the fidelity of the model along an eastern boundary. The results show that the model reproduces the general character of the flow reasonably well, but underestimates both the mean and eddy energies by a substantial amount.     

Dynamics of inorganic nutrient species in the Bohai seawaters

Within the frame of a Sino-German Joint Research Program, two cruises of “R/V Dong Fang Hong 2” were carried out in September–October 1998 and April–May 1999, respectively, to understand the dynamics of nutrients in the Bohai. Nutrient species (NO₃⁻, NO₂⁻, NH₄⁺, PO₄³⁻ and SiO₃²⁻) are determined colorimetrically on board for five anchor and 30 grid stations. In situ incubation experiments are performed to determine planktonic nutrient uptake and benthic exchange flux. Nutrient concentrations display short-term variability and seasonal change in the Bohai, with higher levels in shallow coastal waters than in the Central Bohai. The influence of riverine discharge on nutrient levels can be seen from salinity isopleths, nutrient distribution and species ratios. Near-bottom (nb) waters have similar nutrient concentrations as to the surface waters in the Central Bohai, whereas stratification takes place in the Bohai Strait and North Yellow Sea. In situ incubation experiments provide evidence that the uptake ratio (i.e. N, P) by phytoplankton is proportional to the ratios among nutrient species in ambient waters. Based on the data of this study and previously publications, a preliminary estimate of nutrient budgets via riverine input and atmospheric deposition is established. The results indicate that atmospheric deposition gains importance over rivers in delivering nutrients into the Bohai and sustain the new production, following recent decrease in riverine inflow caused by drought periods in North China and damming practices. A historical review of nutrient data indicates that concentrations of nitrogen increase and phosphorus and silica decrease in the Central Bohai over last 40 years. This potentially has an important influence on the health of ecosystem in Bohai (e.g. food web and community structure), though further study is needed to examine the scenario in more detail.     

Parametric Hull Form Optimization of Containerships for Minimum Resistance in Calm Water and in Waves

This paper described the process of generating the optimal parametric hull shape with a fully parametric modeling method for three containerships of different s...     

基于目标级联分析法的车下设备悬挂参数优化设计

为改善高速列车运行舒适度和车下悬挂设备的振动水平,建立了车辆-设备系统垂向动力学模型,推导了车辆系统振动加速度频率响应函数;结合轨道不平顺激励谱函数计算了车下悬挂设备振动加速度均方根,联合人体舒适度加权滤波函数计算了车体振动参考点的垂向舒适度指标;引入目标级联分析(ATC)法逐层分解车辆-设备系统振动指标,构建了车辆-设备系统两层指标分解数学模型,采用指数罚函数策略协调两层振动指标之间的耦合问题;提出了以车辆运行舒适度和车下悬挂设备振动加速度为指标的多目标优化方法,建立了以车下设备悬挂刚度和阻尼为设计变量的优化模型;联合车下设备悬挂参数动力吸振器(DVA)设计法对比探讨了ATC法在复杂车辆系统参数优化设计中的应用效果。分析结果表明：与DVA设计法相比,ATC法优化后车辆中部舒适度在300 km·h^-1工况下提高了8.5%,设备振动水平减小了约20%;在全速域区间,ATC法对车体中部的振动衰减是DVA设计法的2倍,且对设备的振动衰减比DVA设计法大4.5 dB;与优化前相比,ATC法优化后车辆中部舒适度指标最大提升了15%,设备振动加速度减小了0.18 m·s^-2。由此可见,ATC法可以运用于复杂轨道车辆结构参数优化设计中,能有效改善车辆系统的振动水平,也可为车下设备悬挂参数优化设计提供指导。