Correlation between automotive CO, HC, NO, and PM emission factors from on-road remote sensing: implications for inspection and maintenance programs

Carbon monoxide (CO), hydrocarbon (HC), and nitrogen oxide (NO) emission factors (EFs) are measured with a commercial vehicle emissions remote sensing system (VERSS) during a large-scale vehicle exhaust emissions study in Las Vegas. Particulate matter (PM) EFs are simultaneously measured for individual vehicles with a newly developed PM-VERSS based on ultraviolet backscatter light detection and ranging (Lidar). The effectiveness of CO and HC EFs as proxy for NO and PM EFs for spark-ignition vehicles is evaluated. Poor correlations were found between EFs for pollutants on an individual vehicle basis indicating that high EFs for one or more pollutants cannot be used as a predictor of high EFs for other pollutants. Stronger functional relationships became evident after averaging the EF data in bins based on rank-order of a single pollutant EF. Low overlap between the highest 10% emitters for CO, HC, NO, and PM was found. These results imply that for an effective reduction of the four pollutants, inspection and maintenance (I/M) programs, including clean screening, should measure all four pollutants individually. Fleet average CO and HC concentrations determined by gaseous VERSS were compared with fleet average CO and HC concentrations measured at low-idle and at high-idle during local I/M tests for spark-ignition vehicles. The fleet average CO concentrations measured by I/M tests at either idle were about half of those measured by remote sensing. The fleet average high-idle HC concentration measured by I/M tests was about half of that measured by VERSS while low-idle I/M and VERSS HC average concentrations were in better agreement. For a typical vehicle trip, most of the fuel is burned during non-idle conditions. I/M measurements collected during idling conditions may not be a good indicator of a vehicle’s potential to be a high emitter. VERSS measurements, when the vehicle is under a load, should more effectively identify high emitting vehicles that have a large contribution to the mobile emissions inventory.     

Hub location with flow economies of scale

A characteristic feature of hub and spoke networks is the bundling of flows on the interhub links. This agglomeration of flows leads to reduced travel costs across the interhub links. Current models of hub location do not adequately model the scale economies of flow that accrue due to the agglomeration of flows. This paper shows that current hub location models, by assuming flow-independent costs, not only miscalculate total network cost, but may also erroneously select optimal hub locations and allocations. The model presented in this paper more explicitly models the scale economies that are generated on the interhub links and in doing so provides a more reliable model representation of the reality of hub and spoke networks.     

Fuzzy Logic Active and Semi-Active Control of Off-Road Vehicle Suspensions

For off-road vehicles, minimizing the absorbed power is the main objective of suspension control. The primary cause of increase in the absorbed power in off-road vehicles driven at high speeds on harsh courses is the exhaustion of the suspension travel. Fuzzy-logic approach to active and semi-active off-road vehicle suspension control, with the goal of improving the speed of the vehicle over rough terrains are developed. The ride metric used for quantifying improvements is the absorbed power of the sprung mass. Particular attention is paid to the proper modeling of the suspension using both the full kinematic constraints and the more convenient two degree of freedom linear model of the quarter vehicle suspension. The nonlinearities due to the kinematic constraints on motion are accounted for by modifying the stiffness and damping coefficients of the suspension spring and dashpot in the linear model. The control laws are developed using the less complex model and demonstrated in the fully constrained environment. Nonlinearities of the suspension, including tire stiffness/damping and bumpstops are included at all stages of controller development.     

Exploring the impact of walk–bike infrastructure,safety perception,and built-environment on active transportation mode choice: a random parameter model using New York City commuter data

This study estimates a random parameter (mixed) logit model for active transportation (walk and bicycle) choices for work trips in the New York City (using 2010–2011 Regional Household Travel Survey Data). We explored the effects of traffic safety, walk–bike network facilities, and land use attributes on walk and bicycle mode choice decision in the New York City for home-to-work commute. Applying the flexible econometric structure of random parameter models, we capture the heterogeneity in the decision making process and simulate scenarios considering improvement in walk–bike infrastructure such as sidewalk width and length of bike lane. Our results indicate that increasing sidewalk width, total length of bike lane, and proportion of protected bike lane will increase the likelihood of more people taking active transportation mode This suggests that the local authorities and planning agencies to invest more on building and maintaining the infrastructure for pedestrians. Further, improvement in traffic safety by reducing traffic crashes involving pedestrians and bicyclists, will increase the likelihood of taking active transportation modes. Our results also show positive correlation between number of non-motorized trips by the other family members and the likelihood to choose active transportation mode. The model would be an essential tool to estimate the impact of improving traffic safety and walk–bike infrastructure which will assist in investment decision making.     

A Simplified Model for the Effect of Weld-Induced Residual Stresses on the Axial Ultimate Strength of Stiffened Plates

The present work investigates the compressive axial ultimate strength of fillet-welded steel-plated ship structures subjected to uniaxial compression, in which the residual stresses in the welded plates are calculated by a thermo-elasto-plastic finite element analysis that is used to fit an idealized model of residual stress distribution. The numerical results of ultimate strength based on the simplified model of residual stress show good agreement with those of various methods including the International Association of Classification Societies (IACS) Common Structural Rules (CSR), leading to the conclusion that the simplified model can be effectively used to represent the distribution of residual stresses in steel-plated structures in a wide range of engineering applications. It is concluded that the widths of the tension zones in the welded plates have a quasi-linear behavior with respect to the plate slenderness. The effect of residual stress on the axial strength of the stiffened plate is analyzed and discussed.     

Two degree of freedom flow-induced vibration of cylindrical structures in marine environments: frequency ratio effects

The flow-induced vibration of a cylindrical structure is a very common problem in marine environments such as undersea pipelines, offshore risers, and cables. In this study, the vortex-induced vibration (VIV) of an elastically mounted cylinder at a low Reynolds number is simulated by a transient coupled fluid–structure interaction numerical model. Considering VIV with low damping ratio, the response, hydrodynamic forces, and vortex shedding modes of the cylinder is systematically analyzed and summed up the universal rule under different frequency ratios. On the basis of the analysis, we find that the frequency ratio α is a very important parameter. It decides the locked-in, beat, and phase-switch phenomena of the cylinder, meanwhile, it also influence the vortex mode of the cylinder. The trajectory of the two degrees of freedom (2 DOF) case at different natural frequency ratios is discussed, with most trajectories having a “figure of 8” shape and a few having a “crescent” shape. A fast Fourier transformation technique is used to obtain the frequency characteristics of the vibration of the cylindrical structure. Using the 2 DOF cylinder model in place of the 1 DOF model presents several advantages in simulating the nonlinear characteristics of cylindrical structures, including the capacity to model the crosswise vibration generated by in-line vibration.     

Optimal concession contracts for landlord port authorities with different pursuing goals

This paper investigates how landlord port authorities should offer concession contracts to their terminal operators under two different goals, by building a two-stage game for each goal. If maximizing the weighted sum of fee revenues and throughout benefits is port authorities’ goal, then the optimal concession contract can be any of the two-part tariff, the unit-fee, and the fixed-fee contracts. Accordingly, our special cases include previous works assuming that port authorities maximize either fee revenues or throughput benefits. By contrast, if maximizing the social welfare is the goal, then we find that subsidizing terminal operators, instead of charging them, is port authorities’ best choice. This result is not yet discovered in the literature.     

Assessing the representativeness of a smartphone-based household travel survey in Dar es Salaam,Tanzania

The household travel survey (HTS) finds itself in the midst of rapid technological change. Traditional methods are increasingly being sidelined by digital devices and computational power—for tracking movements, automatically detecting modes and activities, facilitating data collection, etc.. Smartphones have recently emerged as the latest technological enhancement. FMS is a smartphone-based prompted-recall HTS platform, consisting of an app for sensor data collection, a backend for data processing and inference, and a user interface for verification of inferences (e.g., modes, activities, times, etc.). FMS, has been deployed in several cities of the global north, including Singapore. This paper assesses the first use of FMS in a city of the global south, Dar es Salaam. FMS in Dar was implemented over a 1-month period, among 581 adults chosen from 300 randomly selected households. Individuals were provided phones with data plans and the FMS app preloaded. Verification of the collected data occurred every 3 days, via a phone interview. The experiment reveals various social and technical challenges. Models of individual likelihood to participate suggest little bias. Several socioeconomic and demographic characteristics apparently do influence, however, the number of days fully verified per individual. Similar apparent biases emerge when predicting the likelihood of a given day being verified. Some risk of non-random, non-response is, thus, evident.     

无轴轮缘推进器电机与水力部件耦合优化设计研究

针对目前无轴推进器电机与水力部件设计时多未考虑两者耦合的问题,本文提出两者耦合的优化设计方法.采用多参数非线性优化方法,基于电机和导管螺旋桨设计理论公式,并考虑无轴推进器电机转子的直径等同于螺旋桨内径加上叶梢间隙,以及螺旋桨输出转矩加上间隙的摩擦转矩值作为电机输入转矩的关系,建立了一种新型优化设计模型,通过优化方法进行迭代分析,利用5.5 kW无轴推进器进行方法验证.研究结果表明,所提出的优化方法有效地考虑了无轴推进器电机与水力部件的耦合关系,可对推进器效率进行综合优化.     

一种基于卫星导航的列车初始定位方法研究

在西北环境恶劣地区,线路区间往往较少设置实体应答器,列车在区间重启时需要长距离低速运行.经过实体应答器后才能确定列车位置。针对该问题.本文提出一种基于卫星导航系统和车载电子地图的列车初始定位方法。该方法利用轨道约束算法和概率学方法,设计满足铁路安全标准要求的列车初始定位方法。