Correlation between automotive CO, HC, NO, and PM emission factors from on-road remote sensing: implications for inspection and maintenance programs

Carbon monoxide (CO), hydrocarbon (HC), and nitrogen oxide (NO) emission factors (EFs) are measured with a commercial vehicle emissions remote sensing system (VERSS) during a large-scale vehicle exhaust emissions study in Las Vegas. Particulate matter (PM) EFs are simultaneously measured for individual vehicles with a newly developed PM-VERSS based on ultraviolet backscatter light detection and ranging (Lidar). The effectiveness of CO and HC EFs as proxy for NO and PM EFs for spark-ignition vehicles is evaluated. Poor correlations were found between EFs for pollutants on an individual vehicle basis indicating that high EFs for one or more pollutants cannot be used as a predictor of high EFs for other pollutants. Stronger functional relationships became evident after averaging the EF data in bins based on rank-order of a single pollutant EF. Low overlap between the highest 10% emitters for CO, HC, NO, and PM was found. These results imply that for an effective reduction of the four pollutants, inspection and maintenance (I/M) programs, including clean screening, should measure all four pollutants individually. Fleet average CO and HC concentrations determined by gaseous VERSS were compared with fleet average CO and HC concentrations measured at low-idle and at high-idle during local I/M tests for spark-ignition vehicles. The fleet average CO concentrations measured by I/M tests at either idle were about half of those measured by remote sensing. The fleet average high-idle HC concentration measured by I/M tests was about half of that measured by VERSS while low-idle I/M and VERSS HC average concentrations were in better agreement. For a typical vehicle trip, most of the fuel is burned during non-idle conditions. I/M measurements collected during idling conditions may not be a good indicator of a vehicle’s potential to be a high emitter. VERSS measurements, when the vehicle is under a load, should more effectively identify high emitting vehicles that have a large contribution to the mobile emissions inventory.     

Hub location with flow economies of scale

A characteristic feature of hub and spoke networks is the bundling of flows on the interhub links. This agglomeration of flows leads to reduced travel costs across the interhub links. Current models of hub location do not adequately model the scale economies of flow that accrue due to the agglomeration of flows. This paper shows that current hub location models, by assuming flow-independent costs, not only miscalculate total network cost, but may also erroneously select optimal hub locations and allocations. The model presented in this paper more explicitly models the scale economies that are generated on the interhub links and in doing so provides a more reliable model representation of the reality of hub and spoke networks.     

Spatial Dynamics of Multibody Tracked Vehicles Part II: Contact Forces and Simulation Results

In this part of the paper, three dimensional computational capabilities, that includes significant details, are developed for the nonlinear dynamic analysis of large scale spatial tracked vehicles. Three dimensional nonlinear contact force models that describe the interaction between the track links and the vehicle components such as the rollers, sprockets, and idlers as well as the interaction between the track links and the ground are developed and used to define the generalized contact forces associated with the vehicle generalized coordinates. Tangential friction and contact forces are developed in order to maintain the stability of the track motion and avoid the slippage of the track or its rotation as a rigid body. Body and surface coordinate systems are introduced in order to define the spatial contact conditions. The nonlinear equations of motion of the tracked vehicle are solved using the velocity transformation procedure developed in the first part of this paper. This procedure is used in order to obtain a minimum set of differential equations, and avoid the use of the iterative Newton-Raphson algorithm. A computer simulation of a tracked vehicle that consists of one hundred and six bodies and has one hundred and sixteen degrees of freedom is presented in order to demonstrate the use of the formulations presented in this study.     

Spatial Dynamics of Multibody Tracked Vehicles Part I: Spatial Equations of Motion

In this paper, the nonlinear dynamic equations of motion of the three dimensional multibody tracked vehicle systems are developed, taking into consideration the degrees of freedom of the track chains. To avoid the solution of a system of differential and algebraic equations, the recursive kinematic equations of the vehicle are expressed in terms of the independent joint coordinates. In order to take advantage of sparse matrix algorithms, the independent differential equations of the three dimensional tracked vehicles are obtained using the velocity transformation method. The Newton-Euler equations of the vehicle components are defined and used to obtain a sparse matrix structure for the system dynamic equations which are represented in terms of a set of redundant coordinates and the joint forces. The acceleration solution obtained by solving this system of equations is used to define the independent joint accelerations. The use of the recursive equations eliminates the need of using the iterative Newton-Raphson algorithm currently used in the augmented multibody formulations. The numerical difficulties that result from the use of such augmented formulations in the dynamic simulations of complex tracked vehicles are demonstrated. In this investigation, the tracked vehicle system is assumed to consist of three kinematically decoupled subsystems. The first subsystem consists of the chassis, the rollers, the sprockets, and the idlers, while the second and third subsystems consist of the tracks which are modeled as closed kinematic chains that consist of rigid links connected by revolute joints. The singular configurations of the closed kinematic chains of the tracks are also avoided by using a penalty function approach that defines the constraint forces at selected secondary joints of the tracks. The kinematic relationships of the rollers, idlers, and sprockets are expressed in terms of the coordinates of the chassis and the independent joint degrees of freedom, while the kinematic equations of the track links of a track chain are expressed in terms of the coordinates of a selected base link on the chain as well as the independent joint degrees of freedom. Singularities of the transformations of the base bodies are avoided by using Euler parameters. The nonlinear three dimensional contact forces that describe the interaction between the vehicle components as well as the results of the numerical simulations are presented in the second part of this paper.     

An Optimal Self-Tuning Controller for an Active Suspension

An optimal self-tuning control algorithm is presented for vehicle suspension design. The controller, incorporating a weighting controller, state observer and parameter estimator, is designed according to linear optimal control (LQG) theory. Based on the updated estimates of vehicle parameters and states, and the adapted weighting parameters, the LQG controller provides the optimal set of gains over different operating conditions. The feasibility and effectiveness of the proposed self-tuning system was investigated and proved by simulation studies.     

Fuzzy Logic Active and Semi-Active Control of Off-Road Vehicle Suspensions

For off-road vehicles, minimizing the absorbed power is the main objective of suspension control. The primary cause of increase in the absorbed power in off-road vehicles driven at high speeds on harsh courses is the exhaustion of the suspension travel. Fuzzy-logic approach to active and semi-active off-road vehicle suspension control, with the goal of improving the speed of the vehicle over rough terrains are developed. The ride metric used for quantifying improvements is the absorbed power of the sprung mass. Particular attention is paid to the proper modeling of the suspension using both the full kinematic constraints and the more convenient two degree of freedom linear model of the quarter vehicle suspension. The nonlinearities due to the kinematic constraints on motion are accounted for by modifying the stiffness and damping coefficients of the suspension spring and dashpot in the linear model. The control laws are developed using the less complex model and demonstrated in the fully constrained environment. Nonlinearities of the suspension, including tire stiffness/damping and bumpstops are included at all stages of controller development.     

Exploring the impact of walk–bike infrastructure,safety perception,and built-environment on active transportation mode choice: a random parameter model using New York City commuter data

This study estimates a random parameter (mixed) logit model for active transportation (walk and bicycle) choices for work trips in the New York City (using 2010–2011 Regional Household Travel Survey Data). We explored the effects of traffic safety, walk–bike network facilities, and land use attributes on walk and bicycle mode choice decision in the New York City for home-to-work commute. Applying the flexible econometric structure of random parameter models, we capture the heterogeneity in the decision making process and simulate scenarios considering improvement in walk–bike infrastructure such as sidewalk width and length of bike lane. Our results indicate that increasing sidewalk width, total length of bike lane, and proportion of protected bike lane will increase the likelihood of more people taking active transportation mode This suggests that the local authorities and planning agencies to invest more on building and maintaining the infrastructure for pedestrians. Further, improvement in traffic safety by reducing traffic crashes involving pedestrians and bicyclists, will increase the likelihood of taking active transportation modes. Our results also show positive correlation between number of non-motorized trips by the other family members and the likelihood to choose active transportation mode. The model would be an essential tool to estimate the impact of improving traffic safety and walk–bike infrastructure which will assist in investment decision making.     

A Simplified Model for the Effect of Weld-Induced Residual Stresses on the Axial Ultimate Strength of Stiffened Plates

The present work investigates the compressive axial ultimate strength of fillet-welded steel-plated ship structures subjected to uniaxial compression, in which the residual stresses in the welded plates are calculated by a thermo-elasto-plastic finite element analysis that is used to fit an idealized model of residual stress distribution. The numerical results of ultimate strength based on the simplified model of residual stress show good agreement with those of various methods including the International Association of Classification Societies (IACS) Common Structural Rules (CSR), leading to the conclusion that the simplified model can be effectively used to represent the distribution of residual stresses in steel-plated structures in a wide range of engineering applications. It is concluded that the widths of the tension zones in the welded plates have a quasi-linear behavior with respect to the plate slenderness. The effect of residual stress on the axial strength of the stiffened plate is analyzed and discussed.     

Strava Metro data for bicycle monitoring: a literature review

ABSTRACT

Monitoring bicycle trips is no longer limited to traditional sources, such as travel surveys and counts. Strava, a popular fitness tracker, continuously collects human movement trajectories, and its commercial data service, Strava Metro, has enriched bicycle research opportunities over the last five years. Accrued knowledge from colleagues who have already utilised Strava Metro data can be valuable for those seeking expanded monitoring options. To convey such knowledge, this paper synthesises a data overview, extensive literature review on how the data have been applied to deal with drivers’ bicycle-related issues, and implications for future work. The review results indicate that Strava Metro data have the potential—although finite—to be used to identify various travel patterns, estimate travel demand, analyse route choice, control for exposure in crash models, and assess air pollution exposure. However, several challenges, such as the under-representativeness of the general population, bias towards and away from certain groups, and lack of demographic and trip details at the individual level, prevent researchers from depending entirely on the new data source. Cross-use with other sources and validation of reliability with official data could enhance the potentiality.