Improvement of exhaust gas pressure’s utilization for compressing the intake air in diesel engine’s cylinders

In order to improve the economical and environmental performances of the Diesel engines, the present paper aims to bring to the forefront solutions to increase the efficiency of the supercharging process carried out by the aggregates with Comprex type pressure waves. One solution to this is to drive the Comprex, not by the supercharged engine as it currently happens, but by a DC motor. The speed of the electric motor is modified, by means of an electronic management system, depending on the speed and load of the Diesel engine. The paper presents the experimental results obtained during the investigation of a supercharged Diesel engine by the Comprex driven type according to the proposed solution.     

Analysis process of a steering system using a concept model for idle vibration

This paper describes the development of an optimal design process for a steering column system and supporting system. A design guide is proposed at the initial concept stage of the development process to obtain sufficient stiffness of the steering system while reducing the idle vibration sensitivity of the system. Case studies on resonance isolation are summarized, where vibration modes among the systems are separated by applying a vibration mode map at the initial stage of the design process. This study also provides design guidelines for an optimal dynamic damper system using a CAE (computer aided engineering) analysis. The damper FE (finite element) model is added to the vehicle model to analyze the relation between the frequency and the sensitivity of the steering column system. This analysis methodology makes it possible to achieve target performance in the early design stage and reduction of damper tuning activity after the proto car test stage. Through the proposed steering column system development process, a lightweight vehicle with high stiffness is possible prior to the proto build stage. Furthermore, the improved process is expected to contribute to reducing the overall development period and the number of proto car tests necessary to achieve the desired steering system performance.     

Automotive structure vibration with component mode synthesis on a multi-level

The recursive component mode synthesis method (RCMS) has been implemented for the finite element analysis model of an automobile structure as an efficient free vibration analysis tool. The RCMS method is intended to obtain a better performance relative to the block Lanczos method, which is a traditional method in the industry of obtaining eigenvalues, while obtaining the acceptable accuracy. A numerical example of the automobile finite element model demonstrates the outstanding performance of RCMS compared to the block Lanczos method.     

卵砾石层管推进工程超挖及卡钻对管材与土壤互制行为的影响研究

非明挖工法在都市施作时,常因困难地质(如卵砾石层)或障碍物而造成施工困难、工期延误或发生灾损。本文主要针对非明挖施工法里的管推进施工法(Pipe-jacking Method),探讨管推进工法施工时可能遭遇的困难,以及施工困难状况下之管材土体互制行为。探讨的施工困难包括超挖、挤压、卡钻等问题。本研究针对超挖范围、卡钻位置、阻力大小以及推进力施加位置等,以ABAQUS有限元素软件进行三维数值仿真,探讨直线推进施工中的问题。     

Fault detection method for electric parking brake (EPB) systems with sensorless estimation using current ripples

A fault detection method with parity equations is proposed in this paper. Due to its low cost implementation, the velocity of the motor is not measurable in electric parking brake (EPB) systems. Therefore, residuals are not reliable when estimating the motor velocity with a low-resolution encoder. In this paper, we propose a fault detection method with sensorless estimation using current ripples that estimates the position and velocity of the motor by detecting periodical oscillations of the armature current caused by rotor slots. In addition, this method can estimate the position and velocity of the motor with less computational effort than a state observer. Moreover, the method is less sensitive to motor parameters than model-based estimation methods. The effectiveness of this method is validated with experimental data, and the simulation results show that various faults have their own residual patterns. Therefore, we can detect the presence of faults by monitoring the residual signals.     

Design and optimization of an LPG roller vane pump for suppressing cavitation

A roller vane type liquefied petroleum gas (LPG) pump was developed for a liquid phase LPG injection (LPLi) engine. Most of the LPG pumps used in the current LPLi engines are installed inside of the LPG tank, but this pump is intended to be installed outside of the LPG tank to overcome the difficulty of fixing an in-tank pump. Because LPG has a low boiling point and high vapor pressure, it usually causes cavitation in the pump and consequently deteriorates the flow rate of the pump. The purpose of this work is to optimize the design of the roller vane pump in order to suppress cavitation and increase the fuel flow rate by using a computational fluid dynamics (CFD) analysis. In order to achieve these goals, the intake port configuration and the rotor of the roller vane pump were redesigned and simulated using STAR-CD code. Computation was performed for six different models to obtain the optimized design of the roller vane pump at a constant speed of 2600 rpm and a constant pressure difference between the inlet and outlet of 5 bar. The computation results show that an increased intake port cross-section area can suppress cavitation, and the pump can achieve a higher flow rate when the rotor configuration is changed to increase its chamber volume. When the inlet pressure difference is 0.1 bar higher than the fluid saturation pressure, the pump reaches its maximum flow rate.     

Robust lane markings detection and road geometry computation

Detection of lane markings based on a camera sensor can be a low-cost solution to lane departure and curve-over-speed warnings. A number of methods and implementations have been reported in the literature. However, reliable detection is still an issue because of cast shadows, worn and occluded markings, variable ambient lighting conditions, for example. We focus on increasing detection reliability in two ways. First, we employed an image feature other than the commonly used edges: ridges, which we claim addresses this problem better. Second, we adapted RANSAC, a generic robust estimation method, to fit a parametric model of a pair of lane lines to the image features, based on both ridgeness and ridge orientation. In addition, the model was fitted for the left and right lane lines simultaneously to enforce a consistent result. Four measures of interest for driver assistance applications were directly computed from the fitted parametric model at each frame: lane width, lane curvature, and vehicle yaw angle and lateral offset with regard the lane medial axis. We qualitatively assessed our method in video sequences captured on several road types and under very different lighting conditions. We also quantitatively assessed it on synthetic but realistic video sequences for which road geometry and vehicle trajectory ground truth are known.     

Effects of injection parameters on the spray characteristics of swirl and slit injectors using the Mie-scattering method

We investigated the effects of injection parameters such as injection pressure, ambient pressure, and ambient temperature on spray characteristics. We calculated the turbulence occurring point (t _c ), defined as the time required to generate a vortex, and the deceleration point (t _b ), defined as the time when spray penetration begins to decelerate, to elucidate the breakup mechanism of the test injectors. The spray velocity coefficient (C_v) was obtained to evaluate the spray characteristics. As the ambient pressure increases in the case of a slit injector, C_v decreases. We investigated the effects of nozzle tip shape according to injection pressure, ambient pressure, and fuel properties on spray characteristics and provide a C_v value of 0.38 for the swirl injector with a spray angle of 60° and the slit injector under atmospheric conditions. The value of C_v in the case of a slit injector was reduced by increasing the ambient pressure. Our results suggest that C_v of a swirl injector is constant regardless of changes in ambient pressure, injection pressure, and fuel properties. On the other hand, C_v of a slit injector is altered by changes in ambient pressure.     

Development of a navigation algorithm with dead reckoning for unmanned ground vehicles

A navigation algorithm is indispensable for Unmanned Ground Vehicles (UGVs). During driving, UGVs follow a global path. In this study, we propose a navigation algorithm using Real Time Kinematic (RTK)-Differential Global Positioning System (DGPS) units and encoders to complement global path planning. Sometimes GPS systems lose their signals and receive inaccurate position data due to many factors, such as edifice and barrier obstructions. This paper shows that GPS deviations can be solved using a Dead Reckoning (DR) navigation method with encoders and that position errors can be decreased through the use of RTK-DGPS units. In addition to this method, we will introduce a new waypoint update algorithm and a steering algorithm using RTK-DGPS units.     

Torque characteristics analysis for optimal design of a copper-layered eddy current brake system

An enhanced parametric model for a copper-layered eddy current electric machine (retarder) is introduced in this paper. The modeled torque characteristics of the copper-layered electromagnetic retarders are based on the results from a detailed electromagnetic finite element analysis (FEA) of these eddy current machines. The model uses a parameterized double-exponential function to model the steady state speed-torque characteristics of the retarder. The parameters are adjusted for optimal braking performance in conjunction with predicted speed-torque characteristics of a copper-layered retarder. A full vehicle model, along with the proposed retarder speed-torque model has been used to simulate a series braking events. The simulation results show that the peaks of the retarder speed-torque curves must be designed to occur within a specific range of speeds for optimal braking performance.