轻型车用柴油机达国Ⅲ排放试验研究

通过对玉柴2.5L4F国Ⅱ柴油机进行试验优化升级来匹配某轻型车国Ⅲ机的排放要求.试验主要针对电控燃油喷射系统中的喷油器锥角、突出高度、增压器、EGR进行优化升级,结果表明样机能够满足国Ⅲ排放要求.     

Protective effect of glutamine pretreatment on ischemia-reperfusion injury of spinal cord in rabbits

Objective To investigate the effect of glutamine (Gln) on the content of reduced glutathione hormone (GSH) and aminoglutaminic acid (Glu) of spinal cord following ischemia-reperfusion injury. Methods Totally 40 healthy adult male rabbits were randomly divided into five groups: sham-operation group (S group), ischemia-reperfusion injury group (I/R group), low-dose glutamine group (L Gln group), median-dose glutamine group (M Gln group) and high-dose glutamine group (H Gln group). After glutamine preconditioning, the model of spinal cord ischemia-reporfasion injury was established according to Zivin's method. The general status of animals was observed and the changes of Jacobs scoring were recorded in each group. Malondialdehydes (MDA), GSH, Glu and superoxide dismutase (SOD) activity in lumbar spinal cord tissues were determined using chemical colorimetry. The neuron number and deviation rate in spinal cord anterior horn were observed histopathologically. Results There was no significant difference between L Gin group and I/R group in behavior scoring, SOD activity, content of MDA and Glu, neuron number and deviation rate of spinal cord (P>0.05); however, there was a significant difference in GSH content of spinal cord (P<0.05). M Gln group and I/R group differed significantly (P<0.05) in behavior scoring, SOD activity, content of MDA, Glu, GSH, neuron number and deviation rate of spinal cord. Between H Gln group and M Gln group, there was no significant difference in behavior scoring, content of MDA and Glu, SOD activity, neuron number and aberration rate in spinal cord (P>0.05), whereas there was a significant difference in SOD activity and Giu content (P<0.05). Conclusion Pretreatment with medium-dose glutamine has a protective effect on spinal cord ischemia-reporfasion injury in rabbits, which may be related to the maintenance of GSH content, increase of SOD activity and reduction of MDA.     

Fuel economy comparison of conventional drive trains series and parallel hybrid electric step vans

A hybrid electric vehicle (HEV) is a vehicle that combines a conventional propulsion system with an on-board rechargeable energy storage system to achieve better fuel economy than a conventional vehicle HEVs do not have limited ranges like battery electric vehicles, which use batteries charged by an external source. The different propulsion power systems may have common subsystems or components. The objective of this study is to compare the fuel economies of a conventional step van, a series hybrid electric step van (HESV), and a parallel HESV by calculating the fuel consumption using the ADVISOR software by NREL. We also showed the results of the vehicles in different driving cycles including the Central Business District bus cycles, the New York City Cycle, and the US EPA City and Highway cycles.     

Analysis of a regenerative braking system for Hybrid Electric Vehicles using an Electro-Mechanical Brake

The regenerative braking system of the Hybrid Electric Vehicle (HEV) is a key technology that can improve fuel efficiency by 20∼50%, depending on motor size. In the regenerative braking system, the electronically controlled brake subsystem that directs the braking forces into four wheels independently is indispensable. This technology is currently found in the Electronic Stability Program (ESP) and in Vehicle Dynamic Control (VDC). As braking technologies progress toward brake-by-wire systems, the development of Electro-Mechanical Brake (EMB) systems will be very important in the improvement of both fuel consumption and vehicle safety. This paper investigates the modeling and simulation of EMB systems for HEVs. The HEV powertrain was modeled to include the internal combustion engine, electric motor, battery and transmission. The performance simulation for the regenerative braking system of the HEV was performed using MATLAB/Simulink. The control performance of the EMB system was evaluated via the simulation of the regenerative braking of the HEV during various driving conditions.     

Model-based control system design in a urea-SCR aftertreatment system based on NH3 sensor feedback

This paper presents preliminary control system simulation results in a urea-selective catalytic reduction (SCR) aftertreatment system based on NH₃ sensor feedback. A four-state control-oriented lumped parameter model is used to analyze the controllability and observability properties of the urea-SCR plant. A model-based estimator is designed via simulation and a control system is developed with design based on a sliding mode control framework. The control system based on NH₃ sensor feedback is analyzed via simulation by comparing it to a control system developed based on NO_x sensor feedback. Simulation results show that the NH₃ sensor-based strategy performs very similarly in comparison to a NO_x sensor-based strategy. The control system performance metrics for NO_x index, urea index, urea usage, and NH₃ slip suggest that the NO_x sensor can be a potential alternative to a NO_x sensor for urea-SCR control applications.     

Belt routing and safety assessment through computer simulation

Most of the research on safety belt systems has involved crash simulation that only considered a dynamic human model. However, belt routing analysis, usually known as comfort level estimation, is also an important factor in safety belt design, considering that serious injuries of the abdominal region result from the infiltration of a belt into the neck or the chest. Thus, safety belt evaluations using kinematic human models are also needed. In this paper, a belt fit simulation method is suggested. Using the proposed process, both comfort and safety analyses can be performed under the same conditions continuously, and thus the safety belt design parameters, such as the location of anchor points, dummy posture and etc., can be evaluated. In conclusion, this computer process enables a belt system design to reduce injuries.     

Development of an intelligent CAE system for auto-body concept design

The concept design phase is a critical step in auto-body design, as it has a great effect on later design work. This paper describes the implementation of an auto-body structure design in the early stages of a new auto-body developing program. In order to reduce the long design period and analysis error that plagues traditional auto-body concept design, an intelligent CAE system has been successfully developed and implemented based on the UGS NX/API opening platform. This system, the so-called ACD-ICAE (Auto-body concept design-intelligent computer aided engineering) System that means concept design-intelligent computer aided engineering system, employs a fully parametrized template method to build the conceptual auto-body geometry model and FEM model quickly and easily. It also integrates auto-body modeling, analysis and optimization on only one CAD platform via a parametric variables database. Moreover, all parametric variables are shared and updated in different phases of the ACD-ICAE System. A wizard User Interface (UI) based on knowledge of auto-body engineering was developed and used in this system. The procedures implementing the functional diagram of the ACD-ICAE system are also provided. A typical example of a car body concept design with four doors shows that the ACD-ICAE system is efficient and accurate.     

Theoretical method for predicting the weight reduction rate of a box-type car body for rolling stock by material substitution design

In this paper, a theoretical approach is suggested for predicting the structural performances and weight reduction rate of a car body with a box-type section when its material is substituted with a lightweight material for weight saving. For the material substitution design of a car body for rolling stock, bending, axial, and twisting deformations should be considered at constant stiffness and strength conditions. To compare the weight reduction effects on different material applications, some new indices were derived from a structural performance point of view. The derived indices provide good measures to estimate weight reduction by material substitution design and can be effectively applied to the conceptual design of a car body.     

Performance of air conditioners with a gas-liquid separation condenser and one-tank laminated evaporator

In this study, a parallel flow condenser and laminated evaporator for an automotive air-conditioning system were modified to improve performance. Gas-liquid separation type condensers, in which the condenser and receiver drier are integrated, and one-tank laminated type evaporators were developed, and their performances were investigated experimentally using HFC-134a. Heat transfer characteristics in the condenser are examined by means of air temperature, air velocity entering the condenser and inlet pressure of the refrigerant; heat transfer characteristics in the evaporator are examined by means of air temperature, relative humidity, flow rate of air, outlet pressure of refrigerant and superheat. Pressure drops for both evaporator and condenser are also measured, and correlations for pressure drop are derived for the condenser and evaporator, respectively. Air velocity and mass flow rate of the refrigerant have a significant effect on the overall heat transfer coefficient, and flow pass is not significantly influenced by the cooling capacity of the condenser. The overall heat transfer coefficient of the evaporator increases as air flow rate, air temperature and relative humidity increases.     

Grain refinement in bearing steels using a double-quenching heat-treatment process

A double-quenching (D/Q) process is proposed for heat-treating high carbon-chromium bearing steels to improve the fatigue properties through refinement of the microstructure. The new heat treatment method has two steps: The first step is a nitrocarburizing process that results in high surface hardness and lowers the transformation temperature. The second step is the same as in the conventional quenching process but can be conducted at a considerably lower temperature than in conventional quenching. The microstructure in the material that is caused by the D/Q heat treatment is much finer than in the conventional Q/T (quenching and tempering) process. In order to quantify the performance of the proposed heat-treatment process, various mechanical property tests are carried out. The rolling contact fatigue life of double-quenched bearing steels was eight times higher than in bearing steels that were treated by conventional Q/T.