大直径盾构隧道穿越建筑物群变形分析与控制措施北大核心CSCD

大直径盾构隧道掘进施工对土体造成扰动,导致地表产生沉降或隆起,继而严重威胁上部建筑物群的结构安全。文章依托某大直径盾构隧道穿越老旧小区密集建筑物群工程,首先利用二维有限元软件计算关键断面房屋的沉降变形,再对比三维有限元软件的计算结果,分析两种计算方法的适用范围;然后基于三维模型探究了不同初期荷载释放率对盾构穿越引起的地表和房屋变形的影响,最后利用Peck公式计算的理论地表沉降数据,梳理初期荷载释放率、地表沉降、地层损失率三者的内部联系并提出了控制变形的相关措施。研究结果表明,初期荷载释放率越小,地表及房屋沉降也越小,对应的地层损失也越小;对于控制地表变形,减小荷载释放率等同于减小地层损失率;初期荷载释放率、地表沉降、地层损失率这三者减小的量值呈线性关系。     

Experimental research on dynamic responses characteristics and influence laws of gear transmission-propulsion system under gear excitation北大核心CSCD

［Objective］In order to study the dynamic response characteristics and influence laws of a marine gear transmission-propulsion system, a series of bench tests is carried out.［Methods］First, a biaxial gear transmission-propulsion system test bench including a cross connection gear is built. Experiments to test the acceleration response of the gearbox body and propulsion shaft system are then carried out, and the influence of speed, driving mode, axial static thrust, axial dynamic excitation force from the propeller and other factors on the dynamic response characteristics of the system are compared and analyzed. ［Results］The experimental results show that the transmission law of the vibration acceleration response of the gear transmission-propulsion system is mainly at the meshing frequency and its multipliers, as well as peaks in the low frequency band of 30–80 Hz under certain working conditions. ［Conclusion］This study can provide technical support for the vibration and noise reduction design of gear transmission-propulsion systems. © 2022 Journal of Clinical Hepatology. All rights reserved.     

Optimization of bus allocation to depots by minimizing dead kilometers

In metropolitan cities, public transportation service plays a vital role in mobility of people, and it has to introduce new routes more frequently due to the fast development of the city in terms of population growth and city size. Whenever there is introduction of new route or increase in frequency of buses, the non‐revenue kilometers covered by the buses increases as depot and route starting/ending points are at different places. This non‐revenue kilometers or dead kilometers depends on the distance between depot and route starting point/ending point. The dead kilometers not only results in revenue loss but also results in an increase in the operating cost because of the extra kilometers covered by buses. Reduction of dead kilometers is necessary for the economic growth of the public transportation system. Therefore, in this study, the attention is focused on minimizing dead kilometers by optimizing allocation of buses to depots depending upon the shortest distance between depot and route starting/ending points. We consider also depot capacity and time period of operation during allocation of buses to ensure parking safety and proper maintenance of buses. Mathematical model is developed considering the aforementioned parameters, which is a mixed integer program, and applied to Bangalore Metropolitan Transport Corporation (BMTC) routes operating presently in order to obtain optimal bus allocation to depots. Database for dead kilometers of depots in BMTC for all the schedules are generated using the Form‐4 (trip sheet) of each schedule to analyze depot‐wise and division‐wise dead kilometers. This study also suggests alternative locations where depots can be located to reduce dead kilometers. Copyright © 2015 John Wiley & Sons, Ltd.     

Air pollution impact of maritime shipping operations in the port of Houston

Abstract

Major air pollutants from maritime shipping operations are sulfur oxides, nitrogen oxides, and particulate matter emissions from combustion of fuel oil during cruise, berth, and start‐up modes. Sulfur oxides emissions are substantial from steamships burning high‐sulfur residual fuel oil, where shipping contributes 66 percent of the total sulfur dioxide emissions from transportation sources, and almost 3 percent of the total for Harris county, Texas. Nitrogen oxides emissions are significant during cruise conditions for both steamships and motor ships, while particulate emissions are substantial during start‐up and tube cleaning.

Significant marine air pollutant emission sources are found in busy harbor areas such as the Houston Ship Channel. Offshore terminals for unloading large tankers may result in emissions of 10 to 20 tons of sulfur oxides daily per ship, and 3 to 5 tons of nitrogen oxides daily per ship during pumping operations. Trace‐metal constituents present in the oil may catalyze sulfur dioxide and nitrogen dioxide oxidation to their respective sulfate and nitrate aerosols in the humid Texas Gulf Coast atmospheres to aggravate photochemical air pollution problems once the air masses reach industrial and populated urban areas on land. Onshore sulfur dioxide and particulate‐matter emission controls may be necessary for some large ships in port to minimize potential impact on coastal zone air quality.     

Crashworthiness design based on a simplified deceleration pulse

This paper proposes a procedure to improve the design of an automobile crashworthiness using the deceleration pulse in a simplified form as a design variable. A complete vehicle in a full frontal crash was simulated to find its deceleration pulse by finite element method. Based on this deceleration pulse, sled tests were performed, also in a virtual environment. Comparisons between the real deceleration pulse and a simplified pulse were made based on the HIC₁₅ produced. The simplified pulse is developed by dividing the pulse in three phases, each with a constant level of deceleration. Simulations were made to minimize the HIC₁₅ changing parameters in the restraint system and in the deceleration pulse. An expression was found to relate HIC₁₅ and the first phase of the deceleration pulse. A design case using this expression is presented. The benefits of using the pulse as a design variable along with the restraint system are accounted.     

Beyond “Peak Car”: A reflection on the evolution of public sentiment about the role of cars in cities

In this volume, Jones has made a persuasive case for considering recently observed reductions in car use (and sometimes car ownership) in a number of major northern cities as part of an evolutionary process, rather than the consequence of transient conditions such as the economic downturn of 2008 and its relatively slow recovery. In an era bringing new service models for mobility and communications that have important implications for safety, security, the environment and well-being, he points to the role of public attitudes and sentiments that may underlie changing policy priorities and an associated culture change with respect to transport in cities and the reclamation of street space. This paper briefly explores the role of public sentiments and reflects on the apparent emergence of a popular subculture that favors living, if possible, without owning or using cars, in contrast to older subcultures embracing more extreme sentiments that are either Car-centered or emphatically anti-car.     

Economies of density and factor substitution in Dublin city bus services — a translog approach

The primary aim of the paper is to determine a short‐run cost function for Dublin City Bus Services (DCS), using a translog approach. The results show that there are significant economies of density in the transit operation. The results also indicate that the structure of DCS is characterised by a homothetic production function and that partial elasticities of substitution are non‐unitary.     

Study on rail corrugation of a metro tangential track with Cologne-egg type fasteners

In Chinese metro lines, rail corrugation on both tangential and tight curved tracks with Cologne-egg type fasteners is very severe. Based on the viewpoint of friction-induced vibration causing rail corrugation, the rail corrugation on a tangential track with Cologne-egg type fasteners is studied in this paper. A vibration model of an elastic multiple-wheelset-track system with Cologne-egg type fasteners is established. Both the complex eigenvalue analysis and the transient dynamic analysis are performed to study the stability and the dynamic performance of the wheelset-track system. The simulation results show that a low rail support stiffness value is responsible for rail corrugation on the tangential track. When the Cologne-egg fasteners characterised by a lower stiffness value are replaced with the DTVI2 fasteners characterised by a higher stiffness value, rail corrugation disappears. However, rail corrugation on tight curved tracks cannot be suppressed using the same replacement. The above conclusions are consistent with the corrugation occurrences in actual metro tracks.     

Stakeholder Collaboration and Organizational Innovation in the Planning of the Deschutes Estuary Feasibility Study

Coastal managers have sought to enhance the collaborative inputs of stakeholder groups into management activities. Nonetheless, established organizational approaches have led to primarily consultative forms of engagement and constrained citizen involvement in formative activities. In Olympia, Washington, managers overseeing the Deschutes Estuary Feasibility Study (DEFS) implemented an innovative cooperative research planning initiative that diverged from conventional consultative processes. Stakeholders, rather than government officials, identified the research priorities for the socioeconomic component of this restoration feasibility study. This design method altered the traditional roles and responsibilities of different organizational actors, and the involvement of citizen groups in these formative activities changed the relationship between governmental and nongovernmental actors. Using conceptual frameworks from organizational sociology, this study develops insights into the behavior of the organizations involved with the DEFS cooperative planning effort, demonstrating how engaging stakeholders in formative research planning activities may foster new types of collaboration among coastal management organizations.     

Potential of Real-Time Cylinder Pressure Analysis by Using Field Programmable Gate Arrays

In this paper, a Field Programmable Gate Array (FPGA) was used to implement a real-time cylinder pressure analysis. The goal of the project was to improve the accuracy of calculated heat release and center of combustion calculations to enhance the precision of engine control functions. Compared to today’s real-time pressure analysis systems, several additional physical effects were taken into account for this objective. The wall heat transfer was calculated based on the approach published by Hohenberg. A chemical equilibrium with six substances was assumed for the mixture composition and a real-time calculation method was developed. Furthermore, a two-zone model was adapted and implemented for this realtime analysis. The validation of the results and the rating of the improvement in precision were based on GT-SUITE simulation results as an offline reference tool. Compared to state-of-the-art analysis systems, it was possible to reduce the average error of the center of combustion position from 1.6° to 0.5° crank angle (CA) by taking the investigated effects into account. Moreover, it was possible to significantly reduce the time required for the calculation from one complete combustion cycle to 0.2°CA at an engine speed of 3,000 rpm by using a continuous calculation method on the FPGA. This led to an additional improvement of the ability to control the engine, especially under highly dynamic operation conditions.