Nanoparticle emission characteristics and reduction strategies by boost pressure control and injection strategies in a passenger diesel engine

This research attempted to analyze nanoparticles and other harmful exhaust emissions in accordance with injection strategies and air-fuel ratio (AFR) changes for small diesel engines. The emission characteristics were analyzed in the medium-speed condition, which is the main driving range of a diesel engine. In the case of particulate matter (PM), the number of particles was measured, analyzed, and compared to identify the correlation and emission characteristics of nanoparticles by using a dilution device and condensation particle counter (CPC), which are international standards for particle measurement recommended by the Particulate Measurement Programme (PMP). The engine torque tended to be reduced as pilot injections were added, and the torque was increased by the increased boost pressure, but reduced by the exhaust pressure increase in a part of the low-load range. The number of nanoparticles was not influenced greatly by the change in AFR, but the reduction effect on the PM weight was great depending on the boost pressure increase. In addition, the number of nanoparticles tended to increase as the fuel injection timing became closer to TDC in all conditions, and its difference became larger with an increase in AFR. In addition, in the case of the pilot injection, nanoparticle emission showed similar characteristics depending on the main injection timing, but it was increased by advanced injection timing when performing the main injection only, and the number of the nanoparticles increased as pilot injections were added. Last, the optimal conditions for EMS calibration were analyzed by selecting the conditions of torque reduction and NOx increase within 5 % from all of the engine operating conditions; optimized conditions are presented.     

Vibration reduction of H/Shaft using an electromagnetic damper with mode change

The objective of this study is to develop a damper that can reduce the amplitude of vibration in various frequency ranges. Previous H/Shaft vibration reduction methods work in a passive way. A dynamic damper reduces the amplitude of vibration at its first mode, but vibration still appears at the second mode. A mass damper or hollow shaft can shift the natural frequency to a lower or higher region. The fixed operating frequency prevents vibration from being reduced outside the operating frequency range. The proposed damper uses electromagnets as either masses or actuators to change the damper mode between dynamic damper mode and mass damper mode. The electromagnetic damper (EMD) can change its mode to respond to the vibration excitation at both low and high frequencies. The vibration reduction performance was evaluated by FRF tests in laboratory and vehicle conditions. The results were compared with those of a dynamic damper and indicate that the amplitude of vibration is reduced by 95.6 % when the EMD is implemented on an H/Shaft, whereas only 61.9 % vibration reduction is achieved by the dynamic damper.     

A new approach for improving the performance of freight train timetabling of a single-track railway system

A new approach for improving the performance of freight train timetabling for single-track railways is proposed. Using the idea of a fixed-block signaling system, we develop a matrix representation to express the occupation of inter- and intra-station tracks by trains illustrating the train blocking time diagram in its entirety. Train departure times, dwell times, and unnecessary stopping are adjusted to reduce average train travel time and single train travel time. Conflicts between successive stations and within stations are identified and solved. A fuzzy logic system is further used to adjust the range of train departure times and checks are made to determine whether dwell times and time intervals can be adjusted for passenger and freight trains at congested stations to minimize train waiting times. By combining manual scheduling expertise with the fuzzy inference method, timetable efficiency is significantly improved and becomes more flexible.     

The use of gait parameters to evaluate pedestrian behavior at scramble phase signalized intersections

Pedestrian scramble phasing is usually implemented to reduce pedestrian‐vehicle conflicts and therefore increase the safety of the intersection. However, to adequately determine the benefits of scramble phasing, it is necessary to understand how pedestrians react to such an unconventional design. This study investigates changes in pedestrian crossing behavior following the implementation of a scramble phase by examining the spatiotemporal gait parameters (step length and step frequency). This detailed microscopic‐level analysis provides insight into changes in pedestrian walking mechanisms as well as the effect of various pedestrian and intersection characteristics. The study uses video data collected at a scramble phase signalized intersection in Oakland, California. Gait parameters were found to be influenced by pedestrian gender, age, group size, crosswalk length, and pedestrian signal indications. Both average step length and walking speed were significantly higher for diagonally crossing pedestrians compared with pedestrians crossing on the conventional crosswalks. Pedestrians were found to have the tendency to increase their step length more than their step frequency to increase walking speed. It was also found that, compared with men, women generally increase their walking speed by increasing their step frequency more than step length. However, when in non‐compliance with signal indications, women increase their walking speed by increasing their step length more than step frequency. It was also found that older pedestrians do not significantly change their walking behavior when in non‐compliance with signal indications. Copyright © 2014 John Wiley & Sons, Ltd.     

Modeling the interactions between car and bicycle in heterogeneous traffic

In this paper, a new cellular automata model is proposed to simulate the car and bicycle heterogeneous traffic on urban road. To capture the complex interactions between these two types of vehicles, a novel occupancy rule is adopted in the proposed model to consider the variable lateral distances of mixed vehicular traffic. Based on massive simulations, microscopic fundamental diagrams under different bicycle densities are devised. With these, the bicycle's spilling behavior is then investigated and discussed. In order to reflect the interference of a bicycle on a car, the interference transformation from friction state to block state is modeled explicitly. Finally, different simulation results under different occupancy rules indicate that the constant and fixed occupancy rule adopted in the previous studies might lead to overestimation of car flux in the heterogeneous traffic flows with different bicycle densities. Copyright © 2013 John Wiley & Sons, Ltd.     

Identifying optimal data aggregation interval sizes for link and corridor travel time estimation and forecasting

With the recent increase in the deployment of ITS technologies in urban areas throughout the world, traffic management centers have the ability to obtain and archive large amounts of data on the traffic system. These data can be used to estimate current conditions and predict future conditions on the roadway network. A general solution methodology for identifying the optimal aggregation interval sizes for four scenarios is proposed in this article: (1) link travel time estimation, (2) corridor/route travel time estimation, (3) link travel time forecasting, and (4) corridor/route travel time forecasting. The methodology explicitly considers traffic dynamics and frequency of observations. A formulation based on mean square error (MSE) is developed for each of the scenarios and interpreted from a traffic flow perspective. The methodology for estimating the optimal aggregation size is based on (1) the tradeoff between the estimated mean square error of prediction and the variance of the predictor, (2) the differences between estimation and forecasting, and (3) the direct consideration of the correlation between link travel time for corridor/route estimation and forecasting. The proposed methods are demonstrated using travel time data from Houston, Texas, that were collected as part of the automatic vehicle identification (AVI) system of the Houston Transtar system. It was found that the optimal aggregation size is a function of the application and traffic condition.

Vulnerability analysis for large-scale and congested road networks with demand uncertainty

To assess the vulnerability of congested road networks, the commonly used full network scan approach is to evaluate all possible scenarios of link closure using a form of traffic assignment. This approach can be computationally burdensome and may not be viable for identifying the most critical links in large-scale networks. In this study, an “impact area” vulnerability analysis approach is proposed to evaluate the consequences of a link closure within its impact area instead of the whole network. The proposed approach can significantly reduce the search space for determining the most critical links in large-scale networks. In addition, a new vulnerability index is introduced to examine properly the consequences of a link closure. The effects of demand uncertainty and heterogeneous travellers’ risk-taking behaviour are explicitly considered. Numerical results for two different road networks show that in practice the proposed approach is more efficient than traditional full scan approach for identifying the same set of critical links. Numerical results also demonstrate that both stochastic demand and travellers’ risk-taking behaviour have significant impacts on network vulnerability analysis, especially under high network congestion and large demand variations. Ignoring their impacts can underestimate the consequences of link closures and misidentify the most critical links.     

Toxic air pollutants and trucking productivity in the US

This paper introduces toxic air pollutants into the measurement of trucking productivity to obtain true productivity growth. Our results show that omitting or ignoring toxic air pollutants in measuring trucking productivity yields statistically significant biased productivity estimates in for 2002-2005. Trucking productivity growth was understated by the traditional productivity measure, because the latter did not account for reductions in truck air pollution over time. We also find that the difference between traditional and environmental efficiency scores was negligible, suggesting that environmental constraint did not distort efficiency in the trucking sector.     

CFD Analysis of Ship-to-Ship Hydrodynamic Interaction

A numerical study of ship-to-ship interaction forces is performed using a commercial CFD code, and the results are compared with experimental data and with the results of a panel method analysis. Two ship models have been used in the interaction forces analysis: a tug and a tanker, advancing parallel to each other with different lateral distances and two different values of the fluid depth. Computations are carried out with four different flow models: inviscid and viscous flow with the free surface modeled as a rigid wall and inviscid and viscous flow with the deformable free surface. A fair agreement was obtained with available experimental data and results obtained by panel method. The influence of viscosity in the computations is found to be comparatively weak, while the wavemaking effects may be important, at small magnitude of the horizontal clearance.