Potential of Real-Time Cylinder Pressure Analysis by Using Field Programmable Gate Arrays

In this paper, a Field Programmable Gate Array (FPGA) was used to implement a real-time cylinder pressure analysis. The goal of the project was to improve the accuracy of calculated heat release and center of combustion calculations to enhance the precision of engine control functions. Compared to today’s real-time pressure analysis systems, several additional physical effects were taken into account for this objective. The wall heat transfer was calculated based on the approach published by Hohenberg. A chemical equilibrium with six substances was assumed for the mixture composition and a real-time calculation method was developed. Furthermore, a two-zone model was adapted and implemented for this realtime analysis. The validation of the results and the rating of the improvement in precision were based on GT-SUITE simulation results as an offline reference tool. Compared to state-of-the-art analysis systems, it was possible to reduce the average error of the center of combustion position from 1.6° to 0.5° crank angle (CA) by taking the investigated effects into account. Moreover, it was possible to significantly reduce the time required for the calculation from one complete combustion cycle to 0.2°CA at an engine speed of 3,000 rpm by using a continuous calculation method on the FPGA. This led to an additional improvement of the ability to control the engine, especially under highly dynamic operation conditions.     

Requirement-based testing of an automotive ECU considering the behavior of the vehicle

HILS (Hardware In the Loop Simulation) and RBT (Requirement-Based Testing) are widely used to evaluate the performance and reliability of automotive ECUs (Electronic Control Units). The HILS method is used to predict the behavior of ECU-installed vehicles and to evaluate the performance of ECU controllers. RBT evaluates whether the embedded system satisfies the pre-defined requirements. In this study, the behavior of a vehicle is regarded as a system requirement, and an embedded system test procedure that evaluates the system requirement is proposed. In particular, a new method is introduced, which integrates HILS with RBT. Using the proposed method, the behavior of an articulated vehicle equipped with an AWS (All Wheel Steering) ECU is evaluated with RBT software.     

新转化膜在汽车行业内的应用近况

1 引言 伴随着20世纪初Thomas Coslett及其他众多人士的研究工作,在1943年引入了Jernstadt磷酸盐后,诞生了今天人们所熟知的用于镀锌工艺前预浸处理的含钛磷酸氢二钠溶液.使用该磷酸盐后,可以更快地形成更为细小的磷酸锌晶体组织.过去60多年间,这种基础工艺在众人的努力下愈发精细,但是基本的化学特性及功能仍然保持不变.     

Analysis of disc brake instability due to friction-induced vibration using a distributed parameter model

This paper deals with friction-induced vibration of a disc brake system with a constant friction coefficient. A linear, lumped, and distributed parameter model to represent the floating caliper disc brake system is proposed. The complex eigenvalues are used to investigate the dynamic stability, and, in order to verify simulations which are based on the theoretical model, an experimental modal test and dynamometer test are performed. The comparison of experimental and theoretical results shows good agreement, and the analysis indicates that modal coupling due to friction forces is responsible for disc brake squeal. Also, squeal type instability is investigated, using a parametric analysis. This indicates which parameters have influence on the propensity of brake squealing. This is helpful for validating the analysis model and establishing confidence in the experimental results of the modified system. These results may also be useful during system development or diagnostic analysis.     

New nonlinear bushing model for general excitations using Bouc-Wen hysteretic model

Because the characteristics of rubber bushing significantly affect the accuracy of vehicle dynamics simulations, they should be accurately modeled in the vehicle suspension model. In this paper, a new nonlinear bushing model for automotive bushing components is developed to improve the accuracy of vehicle dynamics analysis. Bushing components were first tested to capture the nonlinear and hysteretic behavior of typical elements by using a MTS 3-axis elastomer tester. A simple Bouc-Wen hysteretic differential model was modified to generate a more precise rubber bushing model. A sine wave, step input, and random excitations are imposed on the bushing. The ADAMS program is used to calculate sensitivity and the VisualDOC program is employed to find the optimal parameters for the bushing model. An error function is designed to find optimal parameters of the model. Parameter identification is carried out to satisfy the static and dynamic characteristics due to sine and step excitation inputs. It was proved that the proposed model could predict the bushing forces under sine, step, and random inputs well. The errors are within 10% in the overall range. To show the validity of the proposed model, a numerical example was also carried out. Because the bushing forces due to random excitation input show good agreement with experiments, the proposed bushing model is available in the vehicle dynamics simulation.     

Effect of intake valve swirl on fuel-gas mixing and subsequent combustion in a CAI engine

A fully three-dimensional model was used to investigate the optimal value for intake valve lift in a CAI engine. Uniform mixing in the engine is a key parameter that affects the auto-ignition reliability and thermal efficiency. The method of intake of the air supply often determines the uniformity (or quality) of the fuel-air mixture. In this paper, four strategies were applied for controlling the swirl intensity of intake air. The variation of the intake valve lift induces different swirling and tumbling intensities. Both experimental data and 1D WAVE software (Ricardo, Co.) were coupled with the 3D model to provide pressure and temperature boundary conditions. The initial condition of the EGR mass fraction was also provided by the 1D model. The benchmark scenario (Case 1) was considered as a valve lift with 2 mm for all intake valves. We found that an intake valve lift of 6 mm with the other intake valve closed (i.e., Case 5) yielded the largest swirling (helical motion in the axial direction) and tumbling, which in turn rendered optimal fuel-gas mixing. We also found that fuel distribution affected the auto-ignition sites (or spot). The better the mixing, the greater the gas temperature and combustion efficiency achieved, as seen in Case 5. The NOx level, however, was increased due to the gas temperature. The optimal operating condition is selected from the viewpoints of environmental protection and combustion efficiency.     

A network equilibrium approach for modelling activity-travel pattern scheduling problems in multi-modal transit networks with uncertainty

An understanding of the interaction between individuals’ activities and travel choice behaviour plays an important role in long-term transit service planning. In this paper, an activity-based network equilibrium model for scheduling daily activity-travel patterns (DATPs) in multi-modal transit networks under uncertainty is presented. In the proposed model, the DATP choice problem is transformed into a static traffic assignment problem by constructing a new super-network platform. With the use of the new super-network platform, individuals’ activity and travel choices such as time and space coordination, activity location, activity sequence and duration, and route/mode choices, can be simultaneously considered. In order to capture the stochastic characteristics of different activities, activity utilities are assumed in this study to be time-dependent and stochastic in relation to the activity types. A concept of DATP budget utility is proposed for modelling the uncertainty of activity utility. An efficient solution algorithm without prior enumeration of DATPs is developed for solving the DATP scheduling problem in multi-modal transit networks. Numerical examples are used to illustrate the application of the proposed model and the solution algorithm.     

Are travelers substituting between transportation network companies (TNC) and public buses? A case study in Pittsburgh

Transportation - Transportation network companies (TNC) provide mobility services that are influencing travel behavior in unknown ways due to limited TNC trip-level data. How they interact with...     

The relationship between transportation vulnerability,school attendance,and free transportation to an afterschool program for youth

Transportation - Transportation vulnerability, defined as lack of access to transportation resulting in financial, social, or health consequences, reduces quality of life. While research has...     

基于韧性理论的盾构隧道智能建造北大核心CSCD

以盾构隧道为主的城市轨道交通在十三五期间已取得了跨越式的进步,盾构掘进设备在智能化方面取得了飞速发展,但隧道结构设计、结构制造和现场管片拼装的智能化方面,仍需要大的创新与突破。面对建设韧性智慧城市的战略目标,盾构隧道还存在系列问题亟需解决,如对于新材料的物性认识浅、理论少;传感的布置缺乏针对性,监测感知差;隧道管片拼装大量依靠人工,误差大。解决这些问题的关键在于构建一个基于韧性理论的智能化盾构隧道建造系统,通过利用材料和结构的韧性特点,结合计算机等信息技术,采用韧性设计、智能感知、智能制造、智能拼装等一系列措施,使得隧道结构中的材料可智能感知、结构可精准监测、数据可实时孪生、信息可高效管理、制造可自动操控、过程可全域感知、模型可动态调节、管片可智能拼装,最终实现韧性城市的盾构隧道智能化建设。