对客运专线车站到发线有效长的再认识

分析影响客运专线车站到发线有效长的因素,给出客运专线车站到发线有效长的理论计算方法,根据各型动车组牵引特性参数、CTCS-2级列控系统技术条件,计算并确定客运专线车站到发线有效长为650 m,并从对客运专线能力、工程投资的影响两方面与原确定的700 m到发线有效长度进行对比分析。     

《铁路轨道设计规范》编制的主要内容及特点

《铁路轨道设计规范》为首次编制,为使广大设计人员更好地理解和应用,针对规范编制的主要特点、主要条文的制定原则、重要参数的取值方法进行重点说明。     

大功率中压柴油发电机组的研发和应用

简要论述首台国产电力推进用的3 000 kW船用中压柴油发电机组在机械方面研发的关键技术和机组试验情况.     

沿海地区雨水系统规划研究

前后海片区是深圳特区内填海较集中的地区,排水隐患较多。该文对现状雨水系统进行了分析,指出现状雨水系统存在的问题,并对问题原因进行分析,提出前后海片区雨水系统规划的原则和标准。同时对排水设计标准、旧村改造、山洪截流、填海方式、排水设施维护管理、填海施工组织等方面提出具体改造对策。可供沿海城市类似的雨水系统规划设计参考。     

Comparison of HC species from diesel combustion modes and characterization of a heat-up doc formulation

This study summarizes engine speed and load effects on HC species emissions from premixed charge compression ignition (PCI) and conventional diesel combustion, and it evaluates diesel oxidation catalyst (DOC) formulations on a gas flow reactor for the purpose of diesel particulate filter regeneration or lean NO_x trap desulfation. HC emissions are sampled simultaneously by a Tedlar bag for light HC species and by a Tenax TA™ adsorption trap for semi-volatile HC species, and they are analyzed by gas chromatography with a flame ionization detector. The bulk temperature and residence time during combustion are key parameters that are important for understanding the effects of speed and load on engine-out HC emissions. The degree of post-flame oxidation is higher in PCI than in conventional combustion, and it is increased for PCI with a higher speed and load, as indicated by a lower fuel alkanes/THC ratio, a higher alkenes/fuel alkanes ratio, and a higher methane/THC ratio. Ethene and n-undecane are two representative HC species, and they are used as a surrogate mixture in the gas flow reactor to simulate PCI and conventional combustion with in-cylinder post fuel injection. Among the three DOC formulations tested, the catalyst with constituent precious metals of platinum and palladium (PtPd) showed the best light-off performance, followed by PtPd with an addition of cerium dioxide (PtPd+CeO₂), and platinum (Pt), regardless of exhaust compositions. Conventional combustion exhaust composition shows a lower light-off temperature than that of PCI, regardless of catalyst formulation.     

Lane-following method for high speed autonomous vehicles

This paper presents a steering control method for lane-following in a vehicle using an image sensor. With each image frame acquired from the sensor, the steering control method determines target position and direction, and constructs a travel path from the current position to the target position either as an Arc-path or S-path. The steering angle is calculated from the travel path thus generated, and the vehicle follows the travel path via motor-control. The method was tested using a vehicle dubbed as KAV (Korea Autonomous Vehicle) along an expressway (Seoul Inner Beltway) trajectory with a variety of radii (50 m ∼ 300 m) while traveling at a speed of 60 km/h to 80 km/h. Compared with an experienced human driver, the method showed little much difference in performance in terms of lane-center deviation. The proposed method is currently employed for high speed autonomous driving as well as for stop and go traffic.     

低等级公路特长隧道半横向通风应用与探讨——九寨仙境隧道通风设计

双向行车的隧道通风,除了维持洞内空气的卫生标准和规定的视距外,还必须有利于火灾时的排烟和人车避难,这在特长隧道是很困难的。我国已建成的4 km以上的双向行车隧道,均采用有平行导洞的纵向式通风,但此种方式缺点很多。文章吸取了国外经验,提出采用半横向式通风,并对此种通风方式提出了一些改进意见及推导了应用公式。     

应用流式细胞术检测17β-雌二醇对H2O2诱导的视网膜神经细胞凋亡的保护作用

目的用流式细胞技术(FACS)检测H2O2诱导的视网膜神经细胞凋亡以及17β-雌二醇(βE2)对细胞的保护作用。方法取新生24 h内的SD大鼠进行视网膜神经细胞的原代培养,待细胞培养4-5 d,经不同因素处理后,用MTT法检测细胞存活率,用FACS法检测细胞凋亡率。结果200μmol/L的H2O2能有效诱导视网膜神经细胞凋亡;低浓度的H2O2不能诱导细胞凋亡,但高浓度的H2O2诱导细胞凋亡的同时也导致了正常细胞比率的锐减;10μmol/L的βE2能有效对抗H2O2诱导的视网膜神经细胞凋亡;低浓度的βE2对细胞未表现出保护作用,高浓度的βE2对细胞反而表现出毒性作用。结论一定浓度的βE2在一定范围内能对抗H2O2诱导的视网膜神经细胞凋亡,表现对神经细胞保护的作用。     

Sliding window method for vehicles moving on a long track

The rail is modelled as a simply supported beam in the vehicle–track coupled dynamics. The beam is formulated by a partial differential equation that is transformed into an ordinary differential equation by the method of mode superposition for numerical calculation. However, the size of the matrix that is formed by the mode-superposition method increases significantly with track length, which limits the calculation efficiency. Some methods have been developed to solve this calculation issue, but they diminish the merits of the vehicle–track coupled dynamics, which would systematically investigate the dynamics of a vehicle and a track from the entire vehicle–track system. A new method is developed to resolve this contradiction. First, a theory based on a sliding window is established to improve the computational stability with respect to the length and the window-movement ratio. Then, two methods, namely finite element method analysis and an analytical solution, are used to verify the accuracy of the new method, which is highly efficient when used in a vertical half-vehicle–track coupled model to calculate the vehicle response when the vehicle moves on a long track. The results of the vehicle response calculated with and without the sliding window show good consistency.     

Gasket life criteria at low temperatures adopting proportional compensation for loss of flexibility and conformability

In the automobile industry, the service life of gaskets is defined as the time until which a released gasket recovers 60 % of the original compression. It was observed that the recovery curves of gaskets were highly nonlinear at high temperatures, and relatively nonlinear at temperatures above the room temperature. However, it was also noted that the recovery curves of the gaskets at temperatures below room temperature exhibited linearity with respect to the ln(time). Automotive manufacturers demand gasket life criteria that exceed a specific time or the entire life of a car. In the case of gaskets used at lower temperatures, since materials encounter losses in its flexibility and conformability, the definition of service life specifying a 60 % recovery may not be sufficiently safe to eliminate possible leakages. In this study, new gasket life criteria that could be used at low temperatures were proposed. The new criteria were proposed based on the change in Young’s modulus of the gasket material in order to conserve the sealing capability.